Was this wheel laced correctly?
#51
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,625
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3890 Post(s)
Liked 6,488 Times
in
3,211 Posts
I would use cotton rim tape.
Likes For SurferRosa:
#52
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
I picked up the wheel. They grinded the spokes down and they seem to be an OK length now. That being said, almost the entire length of the rim is scratched now and I assume it’s from the grinder. This is annoying but purely cosmetic and of course not somethin to that can be seen so I’m over it. Likely won’t be going back for anything other than item purchases though, if even.
Any worrisome last minute things I should check for before mounting these?
Any worrisome last minute things I should check for before mounting these?
Feel *every* spoke end. One sharp edge is too many.
Feel every spoke's tension. I grab pairs each side and squeeze towards each other, you go around a few times and you can tell if any are much looser or tighter than the rest on that side - rears have dish and so feel different each side, front should be the same. This is not expert-feel stuff, once around every pair and you'll know what you're doing.
Make sure it's true - if it's not and you assume it is and you ride it and find out later, well, you'll never know.
And just in case they adjusted the bearings, check them.
#53
framebuilder
I thought this was a pretty clever suggestion but when I looked closely at pictures it looked like to me that the spokes were in the right relationship. There wasn't a picture where I could look straight down to see if 2 spokes from each flange where in the right order. This is an easy place for a mistake to happen like you suggested.
#54
Junior Member
Join Date: Dec 2020
Location: Estonia
Posts: 142
Bikes: HVZ Meteor 1979, HVZ Champion 1962, HVZ SS Moskva80 1981, Dürkopp 1936
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 41 Post(s)
Liked 350 Times
in
70 Posts
Just built my first wheel with some spokes that i had laying around, they ended up a bit long, these should be changed/ground down right?
#55
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
Grinding them down in situ would be challenging.
Yes they should be changed - you need the practice.
Likes For oneclick:
#56
smelling the roses
Join Date: Nov 2010
Location: Tixkokob, Yucatán, México
Posts: 15,320
Bikes: 79 Trek 930, 80 Trek 414, 84 Schwinn Letour Luxe (coupled), 92 Schwinn Paramount PDG 5
Mentioned: 104 Post(s)
Tagged: 1 Thread(s)
Quoted: 7081 Post(s)
Liked 901 Times
in
612 Posts
For those echoing the sentiment of learning to build them myself, I hear ya! In the years since joining this forum I've learned to handle most of my own bicycle needs and I'm very grateful for it. I will likely dive into wheel building, but my hopes for this wheel set was a quick turn-around with no room for error as I want to get the bike loaded up for a few camping trips as soon as possible. I assumed tackling the build myself would take lots of time and practice and possible result in failure on a trip. But alas...
I can also recommend Roger Musson's book. I printed the whole thing.
Last edited by seedsbelize; 03-04-21 at 07:58 PM.
#57
Used to be Conspiratemus
Join Date: Jan 2009
Location: Hamilton ON Canada
Posts: 1,512
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 297 Post(s)
Liked 245 Times
in
163 Posts
Pretty good results for spokes you just had lying around. Well done.
Just be careful: The rim strip will deform slightly into the grommets when the tube is inflated. (With a cloth rim tape you can see the persisting dimpling when you remove the tube.). Sometimes the tube can herniate just far enough into the dimple to contact the spoke end. Even through the interposed rim strip this can puncture the tube if you hit a bump just right. It can be an infuriatingly obscure cause of punctures.
Suggest you use a cloth rim strip for better padding if you have any doubt about how much clearance you have in there. If you have to use plastic strip to get the tire to go on, consider this cause if you get punctures on the rim side of the tube over a spoke hole. A fix would be to place nipple washers under each nipple to bring the head of the nipple up to the end of the spoke. I’ve never had to do this but I imagine it’s easier and cheaper than relacing the wheel with new, shorter spokes.
Do this only if you get punctures. It’s probably fine.
Just be careful: The rim strip will deform slightly into the grommets when the tube is inflated. (With a cloth rim tape you can see the persisting dimpling when you remove the tube.). Sometimes the tube can herniate just far enough into the dimple to contact the spoke end. Even through the interposed rim strip this can puncture the tube if you hit a bump just right. It can be an infuriatingly obscure cause of punctures.
Suggest you use a cloth rim strip for better padding if you have any doubt about how much clearance you have in there. If you have to use plastic strip to get the tire to go on, consider this cause if you get punctures on the rim side of the tube over a spoke hole. A fix would be to place nipple washers under each nipple to bring the head of the nipple up to the end of the spoke. I’ve never had to do this but I imagine it’s easier and cheaper than relacing the wheel with new, shorter spokes.
Do this only if you get punctures. It’s probably fine.
Likes For conspiratemus1:
#58
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
Pretty good results for spokes you just had lying around. Well done.
Just be careful: The rim strip will deform slightly into the grommets when the tube is inflated. (With a cloth rim tape you can see the persisting dimpling when you remove the tube.). Sometimes the tube can herniate just far enough into the dimple to contact the spoke end. Even through the interposed rim strip this can puncture the tube if you hit a bump just right. It can be an infuriatingly obscure cause of punctures.
Suggest you use a cloth rim strip for better padding if you have any doubt about how much clearance you have in there. If you have to use plastic strip to get the tire to go on, consider this cause if you get punctures on the rim side of the tube over a spoke hole. A fix would be to place nipple washers under each nipple to bring the head of the nipple up to the end of the spoke. I’ve never had to do this but I imagine it’s easier and cheaper than relacing the wheel with new, shorter spokes.
Do this only if you get punctures. It’s probably fine.
Just be careful: The rim strip will deform slightly into the grommets when the tube is inflated. (With a cloth rim tape you can see the persisting dimpling when you remove the tube.). Sometimes the tube can herniate just far enough into the dimple to contact the spoke end. Even through the interposed rim strip this can puncture the tube if you hit a bump just right. It can be an infuriatingly obscure cause of punctures.
Suggest you use a cloth rim strip for better padding if you have any doubt about how much clearance you have in there. If you have to use plastic strip to get the tire to go on, consider this cause if you get punctures on the rim side of the tube over a spoke hole. A fix would be to place nipple washers under each nipple to bring the head of the nipple up to the end of the spoke. I’ve never had to do this but I imagine it’s easier and cheaper than relacing the wheel with new, shorter spokes.
Do this only if you get punctures. It’s probably fine.
a) he'd need 3 or more washers each to get the nipples far enough away to hide the spoke ends;
b) normal nipple washers won't fit in the eyelet socket; and
c) taking each spoke off to get the washers on the nipple and putting the whole fiddly arangement back would be more work than just taking each spoke off and replacing it with a shorter one.
Last edited by oneclick; 03-06-21 at 11:54 AM.
#59
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
#60
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
I picked up the wheel. They grinded the spokes down and they seem to be an OK length now. That being said, almost the entire length of the rim is scratched now and I assume it’s from the grinder. This is annoying but purely cosmetic and of course not somethin to that can be seen so I’m over it. Likely won’t be going back for anything other than item purchases though, if even.
Any worrisome last minute things I should check for before mounting these?
Any worrisome last minute things I should check for before mounting these?
#61
Senior Member
Join Date: Nov 2013
Location: Near Pottstown, PA: 30 miles NW of Philadelphia
Posts: 2,186
Bikes: 2 Trek Mtn, Cannondale R600 road, 6 vintage road bikes
Mentioned: 83 Post(s)
Tagged: 0 Thread(s)
Quoted: 472 Post(s)
Liked 1,028 Times
in
404 Posts
Sort of an aside here but a friend has a pile of old bike tools, many that he does not understand. One, I realized, is a vintage Eldi spoke nipper. Odd looking tool with a pair of round heads that look badly misaligned. Once I realized what is was I tried it. Very impressive. I was careful to cut across the slot in the spoke nipple (vs along the slot) and it cut clean and easy. I could then unscrew the spoke without any need to dress the cut end.
As mentioned recently, using a too long spoke then nipping the protruding end off sounds nice but you then may not have the threads you need for tension adjustment later. So there is a trade off. Think first. Measure twice and cut once.
As mentioned recently, using a too long spoke then nipping the protruding end off sounds nice but you then may not have the threads you need for tension adjustment later. So there is a trade off. Think first. Measure twice and cut once.
#62
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
I bought a new 1979 Raleigh Super Course where the factory had ground down all the spoke ends in the rear wheel. I was having mystery flats for some time before I found sharp burrs in the aluminum of the Weinmann Concave A124 rims that were left by the coarse grinding wheel. I had to sand out the inside of the rim and was left feeling disgusted by their careless oversight having ruined so many rides by that point. The only good thing about this was that I ended up working at the shop where I had been going for all the patches and tubes. They were a Fuji dealer and my next bike ended up being a Fuji S12S built from shop remnants after my Super Course got stolen. I don't think they were happy that I repainted it without the Fuji Branding (I just wanted it to be silver instead of burgundy).