Clunker Challenge #5
#151
Senior Member
Join Date: Jun 2014
Location: Rat City, WA
Posts: 462
Bikes: Peugeot Course, Motobecane Super Mirage(RIP), Peugeot PKN10e Motobecane Grand Touring
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 13 Times
in
10 Posts
Had to remove a stuck seat post.
I tried everything, until I gave up and tried to cut it out with a hacksaw.
It was not as easy as I was led to believe.
I got almost five hours into it.
A twelve inch hacksaw blade was just long enough.
And the Sawzall blades were to wide to fit inside the tube.
The old seat post was 27.2 MM.
I have quite a few post in different sizes.
One was marked seven dollars, so I'm going with that value.
I found a post that's maybe to short that's 27.2 mm,
and a long post that's 27 mm.
Went with the longer 27mm.
When for a test ride. Instead of avoiding all the bumps in the road preserving
my rotting tires, I hit all the bumps to see if the narrower post would stay in place.
Got a flat.
I tried everything, until I gave up and tried to cut it out with a hacksaw.
It was not as easy as I was led to believe.
I got almost five hours into it.
A twelve inch hacksaw blade was just long enough.
And the Sawzall blades were to wide to fit inside the tube.
The old seat post was 27.2 MM.
I have quite a few post in different sizes.
One was marked seven dollars, so I'm going with that value.
I found a post that's maybe to short that's 27.2 mm,
and a long post that's 27 mm.
Went with the longer 27mm.
When for a test ride. Instead of avoiding all the bumps in the road preserving
my rotting tires, I hit all the bumps to see if the narrower post would stay in place.
Got a flat.
Last edited by Rocky Gravol; 04-20-19 at 11:46 AM.
#152
Senior Member
Join Date: Jul 2018
Location: Eugene, OR
Posts: 1,326
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 535 Post(s)
Liked 346 Times
in
196 Posts
The Johnny Cash approach, “one part at a time.” I’ve got a little ways to go yet before the parts list is all accounted for, and I’m sure that building a couple of wheels is not going to be an easy or quick task, but once there, assembly should be pretty quick. Fingers crossed that enough time will remain to ride the 100 km.
Today, another trip to the co-op yielding a set of brakes towards the clunker build...
Dia-Compe 750 for the rear, and a Racer for the front. The Dia-Compes will ensure successful use of 700c wheels. They have Scott Matthauser pads, but one of them is missing a chunk si will require a little finessing by material reduction to bring them up to speed. The Racer will be the one nod to the frame’s French heritage. Sanding the original pads down should get ‘em good enough for “construction de vélo
— — —
Frame: free plus $30 credit for parts sold
Suntour rear shift lever: $3
SR Crankset: $12
Brakes: $10
=
$5 credit remaining
Today, another trip to the co-op yielding a set of brakes towards the clunker build...
Dia-Compe 750 for the rear, and a Racer for the front. The Dia-Compes will ensure successful use of 700c wheels. They have Scott Matthauser pads, but one of them is missing a chunk si will require a little finessing by material reduction to bring them up to speed. The Racer will be the one nod to the frame’s French heritage. Sanding the original pads down should get ‘em good enough for “construction de vélo
— — —
Frame: free plus $30 credit for parts sold
Suntour rear shift lever: $3
SR Crankset: $12
Brakes: $10
=
$5 credit remaining
Last edited by deux jambes; 04-20-19 at 02:48 PM.
#153
Senior Member
Join Date: Aug 2015
Posts: 3,322
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 1149 Post(s)
Liked 1,773 Times
in
973 Posts
Where is the proper place for a "Kazama" Downhiller II?
The clunker challenge.
Here it is, not mine, for the challenge, The Kazama Downhiller II. My friend told me yesterday that he needed wheels, I got wheels I told him. He rolled his eyes at the thought of my junk (He rejected my last gift of a Raliegh and couldn't stop laughter of thinking of the junkyard PoS's). So the build is not for me, but perfect for the forum.
The clunker challenge.
Here it is, not mine, for the challenge, The Kazama Downhiller II. My friend told me yesterday that he needed wheels, I got wheels I told him. He rolled his eyes at the thought of my junk (He rejected my last gift of a Raliegh and couldn't stop laughter of thinking of the junkyard PoS's). So the build is not for me, but perfect for the forum.
#154
Senior Member
Join Date: Mar 2013
Location: Maryland
Posts: 3,803
Bikes: Lots of English 3-speeds, a couple of old road bikes, 3 mountain bikes, 1 hybrid, and a couple of mash-ups
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 335 Times
in
225 Posts
I've had 4 days to accumulate mileage for the Cimarron, and I am up to 68km now. Next week is kind of busy, but I should hit 100 before the weekend.
#155
Senior Member
Join Date: Jun 2009
Location: Victoria, B.C. Canada
Posts: 304
Bikes: LHT, International, 310
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Well, just did a 3.91 km ride while trying to figure out Strava. Turns out Strava pauses when my phone locks. Wonderful.
I had tried to adjust the front brakes earlier, due to the shoes only touching the rim on a corner, but couldn't find....a 10mm wrench of course. Checked the seat post if it moved, she do. Stem/bars? They do.
Yep, it is me, who is the clunker of this pairing!
5.18/100 km
Edit: Wait, if I am the clunker...is it me who has to be judged?!
I had tried to adjust the front brakes earlier, due to the shoes only touching the rim on a corner, but couldn't find....a 10mm wrench of course. Checked the seat post if it moved, she do. Stem/bars? They do.
Yep, it is me, who is the clunker of this pairing!
5.18/100 km
Edit: Wait, if I am the clunker...is it me who has to be judged?!
Last edited by Oscuro; 04-21-19 at 04:00 PM.
#156
Junior Member
Well I got this just before I read about this challenge. I had serious CL buyers remorse. It looked so perfect in the pics and I was sure I had gotten this Trek 360 for a steal at $80. When I got it I was like... aw crap. I just figured I'd work with it because the orange was blinding me so bad I failed to take a closer look. It rode great and all when I test rode it with the owner. He was also so nice to deliver it to me at the train station - so I bought it.
After closer look I wasn't even sure it was orange to begin with! It's even got two different rims.
I don't think I will win the challenge but I am calling it a clunker. I broke it down already and pulled out the bondo can
it looked so good in the ad!
even orange on the cable!
After closer look I wasn't even sure it was orange to begin with! It's even got two different rims.
I don't think I will win the challenge but I am calling it a clunker. I broke it down already and pulled out the bondo can
it looked so good in the ad!
even orange on the cable!
#157
Full Member
Join Date: Feb 2019
Location: Mid Michigan
Posts: 264
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 66 Post(s)
Likes: 0
Liked 186 Times
in
81 Posts
Here is a update on my Motobecane. I lubed the fork bearings, I think that was the last thing I needed to do. Saturday I road 25.49 miles and 14.80 on Sunday. That give me a total of 52.80 miles.
Saturdays ride.
Sundays ride, this is the church my Grandparents went to. I stop here often for a short rest when riding.
Railroad bridge Sanford MI.
Sanford Lake below the dam.
Sanford Lake above the dam.
Sundays ride.
Saturdays ride.
Sundays ride, this is the church my Grandparents went to. I stop here often for a short rest when riding.
Railroad bridge Sanford MI.
Sanford Lake below the dam.
Sanford Lake above the dam.
Sundays ride.
#158
Senior Member
Join Date: Dec 2005
Posts: 17,180
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3818 Post(s)
Liked 6,752 Times
in
2,626 Posts
I had some time this weekend to clean up my entry, a $40 CL Schwinn LeTour:
I swapped out the lousy saddle it came with for a new cheap one, swapped out the original stem for a used Technomic for more height, swapped out the original non-aero brake levers for some very basic Shimano aero levers, added used Fizik bar tape and plastic bottle cage. Everything else is original to the bike. I haven't test ridden it yet, much less ridden it for 100km, but I'll likely commute on it a couple of times this week and work the kinks out.
I swapped out the lousy saddle it came with for a new cheap one, swapped out the original stem for a used Technomic for more height, swapped out the original non-aero brake levers for some very basic Shimano aero levers, added used Fizik bar tape and plastic bottle cage. Everything else is original to the bike. I haven't test ridden it yet, much less ridden it for 100km, but I'll likely commute on it a couple of times this week and work the kinks out.
#159
Full Member
Join Date: Feb 2019
Location: Mid Michigan
Posts: 264
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 66 Post(s)
Likes: 0
Liked 186 Times
in
81 Posts
Here is what I have done on my Hardrock Sport the last couple days. replaced the inner brake cable. I used the seat post from my Markin parts bike, it was a little small so I made a shim out of a plastic bottle after all this is a clunker. I used a damaged seat left over from another build, it just has a hole in the cover. My wife and I went for a short ride this morning. It was her first time on a mountain bike and her first ride this spring, so we only went 3.13 miles, my total for this bike is 5.80 miles. There are 2 of the decals on the bottom side of the frame that say Paid for by Citizens for responsible government , I wonder if this was a police bike?
Last edited by Oldsledz; 04-21-19 at 08:43 PM.
#162
Not lost wanderer.
Join Date: Jan 2013
Location: Lititz, Pa
Posts: 3,354
Bikes: In USA; 73 Raleigh Super Course dingle speed, 72 Raleigh Gran Sport SS, 72 Geoffry Butler, 81 Centurion Pro-Tour, 74 Gugie Grandier Sportier
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 890 Post(s)
Liked 1,017 Times
in
534 Posts
#166
Senior Member
Join Date: May 2011
Location: Seattle WA
Posts: 2,841
Bikes: 2009 Handsome Devil, 1987 Trek 520 Cirrus, 1978 Motobecane Grand Touring, 1987 Nishiki Cresta GT, 1989 Specialized Allez Former bikes; 1986 Miyata Trail Runner, 1979 Miyata 912, 2011 VO Rando, 1999 Cannondale R800, 1986 Schwinn Passage
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 522 Times
in
367 Posts
Well, just did a 3.91 km ride while trying to figure out Strava. Turns out Strava pauses when my phone locks. Wonderful.
I had tried to adjust the front brakes earlier, due to the shoes only touching the rim on a corner, but couldn't find....a 10mm wrench of course. Checked the seat post if it moved, she do. Stem/bars? They do.
Yep, it is me, who is the clunker of this pairing!
5.18/100 km
Edit: Wait, if I am the clunker...is it me who has to be judged?!
I had tried to adjust the front brakes earlier, due to the shoes only touching the rim on a corner, but couldn't find....a 10mm wrench of course. Checked the seat post if it moved, she do. Stem/bars? They do.
Yep, it is me, who is the clunker of this pairing!
5.18/100 km
Edit: Wait, if I am the clunker...is it me who has to be judged?!
#167
Full Member
100k!
A last quick ride down the mountain (and very slow climb back up!) got in the last 11 miles late yesterday. But I was able to build the bike as a climber so I could make that particular trip without getting out of the saddle and it works. Mostly. While the microshift rear d/r works fine on friction mode, SIS mode works well only on upshifting. I can live with it. But having completed the challenge I've already upgraded the tires to foldables (Espoir Gripton 25s) from the cheap CSR wired ones. And I've got to find a lighter quill stem. The multi-adjustable things are great for being able to find just the "right" (or just possibly acceptable for temporary use?) fit. It weighs about 2 lbs. It isn't included on my cost list because I've had it for years and use it on every build for trial and error sizing. I hope it isn't a serious rules violation. Unlike the note of question I will post next with my costs list which may open a can of worms so large the Grand Master (Executioner?) may bar me from even future clunker challenges.
Likes For grayEZrider:
#169
Senior Member
Join Date: May 2013
Location: Greenwood SC USA
Posts: 2,254
Bikes: 2002 Mercian Vincitore, 1982 Mercian Colorado, 1976 Puch Royal X, 1973 Raleigh Competition, 1971 Gitane Tour de France and others
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 1,396 Times
in
694 Posts
I’ve been home doing childcare this week. Their screen time gave me some wrench time in the workshop. I wiped the worst of the muck off the cranks, then poked around in the parts bin until I found my stash of cotters. I located a used one with a similar profile to what appears to be the original drive side cotter. I was most pleased when the cranks were suddenly in register, more than a bit irritated that I had to keep fiddling with the BB adjustment. Eventually it was right.
This bike came with mismatched brake levers. I have plans for the Weinmann that came on the right side and the original Universal on the left had the usual body crack. I hauled out the bin with the brake parts seeking levers for this and the Bianchi Timber Wolf that is marked for drop bar conversion. When I saw the grubby yellow Dia Compe aero hoods and the Shimano Exage aero levers, I looked over at this taxi cab yellow beast and made my decision. It took some armor all as lube, some thoughtful stretching of things and a healthy dose of brute force but it all went together. We’ll just ignore those gaping holes where the plastic trim rings should go.
Update - I managed another half hour, long enough to pump up the ancient tires, fit the original nutted hub wheels (13 mm front, 14 mm rear?), wipe down and lube the chain and fit it back on the bike, oil and fit the pedals and test the drive train. It works, though it won't win awards.
Last edited by rustystrings61; 04-24-19 at 05:44 AM.
#170
Full Member
Matching yellow hoods? A clunker with class. I love it!
#171
Full Member
Is my newest stable member a disqualified clunker?
Keeper no.6
OK, here is my cost list for the Clunker '19 challenge.
Frame: $ 50 A 1988 Centurion LeMans
tires: 26 CST wired 25cm
RD: 12 Microshift long cage 6/7 speed
Freewheel: 9 14-34 Mega-range Shimano
DR extender: 2
total $ 97
The Sugino triple with a 28 small ring and the mega-range with the 34 gets me up the mountain seated. Although some people walk faster! Aside from wanting to replace the stem I have to do something about the pedals. Recycled wal-mart junk, and they are not even a matched pair. Not sure how I managed that. Is there a cheap light set available worth buying?
OK now. Sharp riders will notice the list is lacking a few useful items like handlebars, shifters, brakes and seat. That stuff came from a previous clunker build (bought for $10) which was stripped and the frame junked. What is the ruling on (now thrice) recycled stuff? Also I've already changed the tires to foldable Espoir blackbelt 25s and the ride (at 75psi) is much better.
#172
Full Member
Join Date: Feb 2019
Location: Mid Michigan
Posts: 264
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 66 Post(s)
Likes: 0
Liked 186 Times
in
81 Posts
I put 13.32 miles on my Motobecane yesterday that give me a total of 65.68 miles or 105.70 Km For cost I got the bike as part of a package deal from a man that runs a recycling and trash compactor site for 25.00. I sold a AMF Sportmaster that was part of the package for 15.00. So I have 10.00 into the other 4 bikes, I will give each of the a value of 2.50. I have been using parts from one of them so far parts went to 2 of the other 3 bikes. For this bike I used from the parts bike both tires, one tube and 4 brake pads I will take 1.50 of value from the parts bike and put it on this one, so I have 2.50 for the bike plus 1.50 for parts giving me 4.00 into the bike.
Side door of the county court house.
Side door of the county court house.
#173
Senior Member
Join Date: Jun 2014
Location: Rat City, WA
Posts: 462
Bikes: Peugeot Course, Motobecane Super Mirage(RIP), Peugeot PKN10e Motobecane Grand Touring
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 13 Times
in
10 Posts
Went on a 35km ride yesterday.
The longest ride I've done in two years.
Since I was diagnosed with Multiple Myeloma.
The Seattle Center International Fountain.
With the Space Needle in the background.
Have 75 km now.
If I were to post this on a Multiple Myeloma forum, it'd be a big deal.
I like this challenge.
The longest ride I've done in two years.
Since I was diagnosed with Multiple Myeloma.
The Seattle Center International Fountain.
With the Space Needle in the background.
Have 75 km now.
If I were to post this on a Multiple Myeloma forum, it'd be a big deal.
I like this challenge.
Last edited by Rocky Gravol; 04-26-19 at 01:59 PM.
#174
Senior Member
Join Date: May 2011
Location: Seattle WA
Posts: 2,841
Bikes: 2009 Handsome Devil, 1987 Trek 520 Cirrus, 1978 Motobecane Grand Touring, 1987 Nishiki Cresta GT, 1989 Specialized Allez Former bikes; 1986 Miyata Trail Runner, 1979 Miyata 912, 2011 VO Rando, 1999 Cannondale R800, 1986 Schwinn Passage
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 522 Times
in
367 Posts
Went on a 35km ride yesterday.
The longest ride I've done in two years.
Since I was diagnosed with Multiple Myeloma.
The Seattle Center International Fountain.
With the Space Needle in the background.
Have 75 km now.
If I were to post this on a Multiple Myeloma forum, it'd be a big deal.
I like this challenge.
The longest ride I've done in two years.
Since I was diagnosed with Multiple Myeloma.
The Seattle Center International Fountain.
With the Space Needle in the background.
Have 75 km now.
If I were to post this on a Multiple Myeloma forum, it'd be a big deal.
I like this challenge.
#175
Senior Member
Join Date: Aug 2018
Posts: 315
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 106 Post(s)
Likes: 0
Liked 36 Times
in
23 Posts
Ok... so switched out saddles and bars... bought bar tape.
cost so far:
idale 90 saddle- came off a Liberia mixte I bought for $25. Also harvested Bar-cons off of it, so let’s say $15.
itm stem- off a $50 Atala I sold for $60... so -$10
bar tape- $12
chain- in a bag of stuff at the thrift store... $7
tires- don’t remember where they came from, but they are used... $20
the rest-free
total=$44
now, I just need to ride.
cost so far:
idale 90 saddle- came off a Liberia mixte I bought for $25. Also harvested Bar-cons off of it, so let’s say $15.
itm stem- off a $50 Atala I sold for $60... so -$10
bar tape- $12
chain- in a bag of stuff at the thrift store... $7
tires- don’t remember where they came from, but they are used... $20
the rest-free
total=$44
now, I just need to ride.