This is why you need eggbeaters for cross.
#1
Senior Member
Thread Starter
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,026 Times
in
723 Posts
This is why you need eggbeaters for cross.
Since my first foray into clipless was well before the advent of crankbrothers I just lived with the occasional inconvenience of having slightly clogged spd pedals. As my kids needed clipless I started by giving them older pairs of pedals I accumulated over the years, the mud this season resulted in several races that were difficult to clip into but it was the final race of the season that convinced me that over the next year we're switching to some form of eggbeaters for pedals.
My 11yo complained they couldn't clip in. This is how much was still in the pedal after driving in the rain for 8 hours and sitting on the back of the car overnight in a downpour.
So much mud had built up on the last lap that the tires stopped spinning, thankfully the kid was near the pit and most of the mud could be cleared out for them.
Interestingly, even though the headset now feels slightly notchy, and the first BB which was new this year seized halfway through the season, the 8000 series XT hubs are spinning completely free with no evidence of any grit in them. Still going to tear them down and regrease them since its been 2 years since they were last done, but impressive sealing all things considered.
My 11yo complained they couldn't clip in. This is how much was still in the pedal after driving in the rain for 8 hours and sitting on the back of the car overnight in a downpour.
So much mud had built up on the last lap that the tires stopped spinning, thankfully the kid was near the pit and most of the mud could be cleared out for them.
Interestingly, even though the headset now feels slightly notchy, and the first BB which was new this year seized halfway through the season, the 8000 series XT hubs are spinning completely free with no evidence of any grit in them. Still going to tear them down and regrease them since its been 2 years since they were last done, but impressive sealing all things considered.
Likes For Russ Roth:
#3
Senior Member
Thread Starter
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,026 Times
in
723 Posts
Likes For Russ Roth:
#4
Senior Member
Join Date: Aug 2014
Location: UK
Posts: 748
Bikes: Dahon Jetstream p8 (sold), customized Dahon Helios x10, customzed Dahon Smooth Hound x11,customized Dahon Hammerhead 8.0 d7, Planet X Free Ranger (mullet setup 1x11), Planet X Giovanissimi 20 (1x9), Frog 52 (1x9) and Frog 48 1s
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 267 Post(s)
Liked 240 Times
in
176 Posts
yes, the 520 can be a little bulky and clogged with mud. This is why I rode with the XT version. These days, in UK muddy cyclocross I ride with garmin rally and I have not problem although the pedal is bulkier like a m540
This was after a XC race on November 11th... 50 shades of mud
This was after a XC race on November 11th... 50 shades of mud
Last edited by Fentuz; 01-11-24 at 10:20 AM.
#5
Senior Member
Join Date: Mar 2006
Location: Chicago, IL, USA
Posts: 2,880
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 1461 Post(s)
Liked 1,486 Times
in
870 Posts
I've heard/read complaints that Egg Beaters are hard to get used to because the engagement is a lot different than SPD. People talk about feeling like they're going to suddenly pull out of the pedals because the unclipping is really vague. I've also heard that reliability is an issue.
They do seem to be a much better design for mud, and I've been in CX races where it was impossible to get clipped back in because the pedals are jammed. I'm intrigued by the design, but I'm also not racing at a high enough level or in mud races frequently enough for this to be a big factor so I've always just stuck with SPDs.
I'm curious to hear opinions of anyone who's made the switch.
They do seem to be a much better design for mud, and I've been in CX races where it was impossible to get clipped back in because the pedals are jammed. I'm intrigued by the design, but I'm also not racing at a high enough level or in mud races frequently enough for this to be a big factor so I've always just stuck with SPDs.
I'm curious to hear opinions of anyone who's made the switch.
#6
Senior Member
Thread Starter
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,026 Times
in
723 Posts
That's about what the rest of the bike looked like but with a little more grass mixed in.
My wife did the switch years ago not liking how hard it was to get out of her spd. She has one pedal she has a hard time getting into on her gravel bike but no trouble with 3 other pairs. In general she likes them better than spd.
I've heard/read complaints that Egg Beaters are hard to get used to because the engagement is a lot different than SPD. People talk about feeling like they're going to suddenly pull out of the pedals because the unclipping is really vague. I've also heard that reliability is an issue.
I'm curious to hear opinions of anyone who's made the switch.
I'm curious to hear opinions of anyone who's made the switch.