Is it normal for a MTB shoe cleat to touch the ground?
05-06-17, 10:29 PM
#1
Junior Member
Thread Starter
Join Date: Aug 2012
Location: Toronto
Posts: 135
Bikes: 2013 Giant Roam XR1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 12 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Is it normal for a MTB shoe cleat to touch the ground?
I finally got clipless shoes and pedals this season!
Now I understand that road shoes are basically unwalkable due to the cleat design.
But I have MTB shoes. And I can still hear the cleat clicking on the ground when I am walking my bike through a cross walk, or walking on pavement, etc. The cleat is recessed between the treads, but it's not totally recessed. It touches the ground. Is this normal?
Here is a photo of one of the cleats, and you can see it's getting scuffed up a lot:
https://i.pictr.io/n8Lx.jpg
This pedal and shoe setup was professionally done in a bike shop. They had me up on the trainer pedalling, with a laser beam down the centre of my knee to ensure everything was aligned right.
Now I understand that road shoes are basically unwalkable due to the cleat design.
But I have MTB shoes. And I can still hear the cleat clicking on the ground when I am walking my bike through a cross walk, or walking on pavement, etc. The cleat is recessed between the treads, but it's not totally recessed. It touches the ground. Is this normal?
Here is a photo of one of the cleats, and you can see it's getting scuffed up a lot:
https://i.pictr.io/n8Lx.jpg
This pedal and shoe setup was professionally done in a bike shop. They had me up on the trainer pedalling, with a laser beam down the centre of my knee to ensure everything was aligned right.
Last edited by SPiN 360; 05-06-17 at 10:43 PM.
05-06-17, 10:38 PM
#2
Senior Member
Yes, that's normal. Some shoes are a little better than others about it.
05-07-17, 06:56 AM
#4
a big man
Join Date: Oct 2007
Location: Spokane
Posts: 262
Bikes: Trek 4300; Motobecane Vent Noir
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 21 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Very normal to have some cleat tapping on hard surfaces. If the cleat scuffs bother you, your bike shop should have some touch up paint, or I've used rustoleum with good success.
05-07-17, 07:24 AM
#6
don't try this at home.
Join Date: Jan 2006
Location: N. KY
Posts: 5,968
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 521 Times
in
358 Posts
?
both mountain shoes I've used had the cleat about level with the shoe lugs. I can hear it grinding on a tile floor, so I try to avoid walking on tile or on varnished wood floors that might get scratched. It's fine otherwise, the cleat isn't harmed by walking, even on concrete.
Perhaps some shoe goo could build up the lugs a little, but it wouldn't last too long.
After four years:
both mountain shoes I've used had the cleat about level with the shoe lugs. I can hear it grinding on a tile floor, so I try to avoid walking on tile or on varnished wood floors that might get scratched. It's fine otherwise, the cleat isn't harmed by walking, even on concrete.
Perhaps some shoe goo could build up the lugs a little, but it wouldn't last too long.
After four years:
Last edited by rm -rf; 05-07-17 at 07:37 AM.
05-07-17, 02:42 PM
#8
Banned
Join Date: May 2017
Posts: 384
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 285 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
yeah, it's normal. I really do wish the cleat section was fully recessed but it could add weight which most riders would not want. It's a tradeoff: a little bit of noise and tiny bit of wear in exchange for lighter shoes.
05-07-17, 07:23 PM
#9
Junior Member
Yep. Its normal. Walking into the local deli for breakfast before a ride people are always staring as they hear click-click-click going down the tile floor.
