Danger Of Damaging A Built-in Seat Post Clamp By Over-Tightening?
#1
Member
Thread Starter
Danger Of Damaging A Built-in Seat Post Clamp By Over-Tightening?
I have a great frame, a Soma Smoothie ES. One fault I don't like about it is the built-in seat post clamp.
My seat post keeps slipping downward after long rides. I keep tightening it. Is there a danger of tearing the welds on the threaded lugs by over tightening?
I am a klidesdale at 6'5" - 240LBS.
My seat post keeps slipping downward after long rides. I keep tightening it. Is there a danger of tearing the welds on the threaded lugs by over tightening?
I am a klidesdale at 6'5" - 240LBS.
#2
Primate
Join Date: Jan 2006
Location: gone
Posts: 2,579
Bikes: Concorde Columbus SL, Rocky Mountain Edge, Sparta stadfiets
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
Yes, you could wreck the clamp.
I have a similar problem on an old Italian bike. The ears are now touching. A longer seatpost seems to jam in the tube better.
You could try using an assembly paste in place of grease on the post.
I have a similar problem on an old Italian bike. The ears are now touching. A longer seatpost seems to jam in the tube better.
You could try using an assembly paste in place of grease on the post.
#3
Senior Member
Join Date: Nov 2008
Location: Bay Area, Calif.
Posts: 7,239
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 659 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
There shouldn't be a need for periodic retightening. I wonder if your seatpost is slightly too small for your frame. Have you tried a post that's one size up in diameter to see if it might fit? Might also try a shim together with your current post (soda cans usually work well as shim material).
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
If (big if) your seat tube projects above the top tube enough to allow you to fit a seatpost clamping collar you could grind off the ears and replace them with the collar and then you can tighten it to your heart's (and seatpost's) content.
Other possiblities are that your seatpost is the wrong size or is at the minimum diameter or your seat tube is too large so you can't get a proper fit. You might try a different seatpost or go up one size.
Other possiblities are that your seatpost is the wrong size or is at the minimum diameter or your seat tube is too large so you can't get a proper fit. You might try a different seatpost or go up one size.
#5
Primate
Join Date: Jan 2006
Location: gone
Posts: 2,579
Bikes: Concorde Columbus SL, Rocky Mountain Edge, Sparta stadfiets
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
^Good idea...
... and he could grind off those rack mounts while he's at it.
(jkng)
... and he could grind off those rack mounts while he's at it.
(jkng)
#6
Senior Member
Join Date: Dec 2005
Posts: 7,848
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
+1 in the assembly paste, what you can do is to use a sleeve made of a coke can, the material is pretty thin.
The other solution and im looking in to this because of a noisy seatpost is to use liquid electrical tape inside of the seatpost.
Good luck.
The other solution and im looking in to this because of a noisy seatpost is to use liquid electrical tape inside of the seatpost.
Good luck.
#7
Senior Member
Join Date: Aug 2007
Location: NorCal
Posts: 546
Bikes: 2009 Surly Cross Check Frankenbike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Have a shop check the seat tube to check the sizing, this will at least tell you if the seat tube is off a little. Then you can make the proper decision regarding a new seat post or shim.
Make sure the bolt is greased, so you get proper feel for torque when you tighten it. A torque wrench will tell you have it torqued properly (meaning you want to avoid too much as well as too little). It shouldn't take a hell of a lot if the post and seat tube are a proper match. You are obviously better off with a shim than a jacked-up clamp.
Make sure the bolt is greased, so you get proper feel for torque when you tighten it. A torque wrench will tell you have it torqued properly (meaning you want to avoid too much as well as too little). It shouldn't take a hell of a lot if the post and seat tube are a proper match. You are obviously better off with a shim than a jacked-up clamp.
#8
Senior Member
Join Date: Apr 2005
Location: The Woodlands, TX
Posts: 177
Bikes: Gary Fisher Zebrano
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I also have a Soma Smoothie ES. I have to tighten the binder bolt to the max "hand tight" (one hand) to keep the post from slipping. As a result, the eyelets/lugs are pinched together. I do use thread lube on the bolt. The welds appear to be intact. The Thomson seatpost was provided by the shop that did the build for me (the post is the right size) Do I have a problem here? Any thoughts/ideas will be appreciated. Thx.