Tubulars - A Different Slant
#1
Senior Member
Thread Starter
Join Date: Jan 2011
Location: Pinehurst, NC, US
Posts: 1,716
Bikes: 2020 Trek Emonda SL6, 90's Vintage EL-OS Steel Bianchi with 2014 Campy Chorus Upgrade
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 452 Post(s)
Liked 162 Times
in
110 Posts
Tubulars - A Different Slant
I am rapidly 'aging out' (maybe already have) of generating satisfying (to me) road cycling results (DOB is 1949). In my case this would be times in a organized or maybe solo century, possibly the random Strava KOM, etc. But for those occasional 'competitive' rides I like to have good equipment. Currently I am riding a new Emonda SL6 (rim brakes) and my 'race wheels' are clincher/latex/Conti Vittoria Bontrager RXL's (2014 vintage). The wheels are relatively light but are not truly aero wheels and are not the lightest around either.
While I am not inclined to go spend $2.5K on some flavor of new ZIPP's, it occurred to me that there probably is a decent buyer's market for used, rim brake tubulars since many are converting to disk (disc?) and tubulars are going out of fashion.
If I did this they would be wheels ridden only very occasionally and I would leave it up to my LBS to deal with tire installation stuff (other than being sure that I can handle a flat on the road). I just wondered what others thought about this concept (whether I go for saving another couple hundred grams or get more aero - probably go for aero). And I am aware that incremental performance gains from wheels better than what I own will be quite small.
dave
ps. The major cycling goal for 2020 will be to ride (rather than survive) the Six Gap Century.
While I am not inclined to go spend $2.5K on some flavor of new ZIPP's, it occurred to me that there probably is a decent buyer's market for used, rim brake tubulars since many are converting to disk (disc?) and tubulars are going out of fashion.
If I did this they would be wheels ridden only very occasionally and I would leave it up to my LBS to deal with tire installation stuff (other than being sure that I can handle a flat on the road). I just wondered what others thought about this concept (whether I go for saving another couple hundred grams or get more aero - probably go for aero). And I am aware that incremental performance gains from wheels better than what I own will be quite small.
dave
ps. The major cycling goal for 2020 will be to ride (rather than survive) the Six Gap Century.
#2
Senior Member
The good thing with tubulars is that you can get both. My 50mm/60mm (I think) wheels are supposed to be under 1400g. Paid $400 for them if I recall correctly.
#3
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
A carbon clincher rim with a set of high-end clincher tires coupled with latex tubes will roll faster, be more aero, and be VASTLY easier to maintain on the road than a set of tubular tires. Unless your heart is set on tubular tires, there aren't many reasons to run them.
#4
Chases Dogs for Sport
I have occasionally thought about the same thing over the years. I have worked wheel trucks for pros that use tubulars -- and seeing their experiences perhaps educated me too much. The thought of dealing with a flat on the road, unsupported, kept me away.
#5
Senior Member
Thread Starter
Join Date: Jan 2011
Location: Pinehurst, NC, US
Posts: 1,716
Bikes: 2020 Trek Emonda SL6, 90's Vintage EL-OS Steel Bianchi with 2014 Campy Chorus Upgrade
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 452 Post(s)
Liked 162 Times
in
110 Posts
A carbon clincher rim with a set of high-end clincher tires coupled with latex tubes will roll faster, be more aero, and be VASTLY easier to maintain on the road than a set of tubular tires. Unless your heart is set on tubular tires, there aren't many reasons to run them.
dave
#6
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
The cost of two nicer tubular tires could potentially offset the cost difference between a set of tubular wheels vs clincher wheels. Two GP5K's with tubes costs about the same as one high-end tubular tire.
#7
Senior Member
Join Date: Sep 2012
Location: Los Angeles
Posts: 755
Bikes: 2019 CAAD12, 2015 Specialized Sirrus Comp
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 562 Post(s)
Likes: 0
Liked 64 Times
in
46 Posts
Dave, on Proscloset, there are quite a few used carbon sew-up wheels for sale, all at lower prices compared to their clincher counterparts. The one consideration is that in many cases, the rims and the hubs are a couple generations old. The only reason I didn't go in this direction is that I wanted a tubeless compatible setup, and didn't want to worry about heat dissipation on the downhills. I don't believe that's an issue with sew-ups.
#8
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2952 Post(s)
Liked 3,106 Times
in
1,417 Posts
Is Six Gap hilly? I'm guessing it is from the name. Personally I would feel much more comfortable running tubulars than clinchers (if we're talking carbon to carbon) on a ride with lots of braking.
Likes For caloso:
#9
Senior Member
Join Date: Apr 2012
Location: Nor Cal
Posts: 6,016
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1814 Post(s)
Likes: 0
Liked 923 Times
in
569 Posts
Definitely true IME, although it would vary by area- more racing= more cast-off race wheels.
I'm currently on 50mm China carbon wheels that I got w/ tires for $200, and rode many miles on Easton EC90s that were the same price.
Also have a couple of sets of Mavik SL that were ~$100. The most I've paid is I think $325 for EC90SL w/good CX tires & DA cassette.
So I have the road set, another set for winter/poor road conditions (DA carbon w/Pave tires); for the CX bike there is an all around set (alloy w/ 30mm Schwalbe),
a gravel/back road set (alloy w/ Knobby Tufos), a CX race set (Easton w/Challenge tires), and another set w/Tufo road tires. All ready to go & total cost much less
than one $$ carbon wheelset. It only takes a few minutes to change wheels (only the CX race wheels require changing brake pads).
Paying a shop to mount tires would eat up some of the savings, and buying the tires on sale is a factor in keeping cost down.
To the poster above concerned about changing a tire on the road- it's the same or easier/faster than clincher, NBD.
Mounting a tire later is more work than clincher but still less than some folks seem to put into washing their bike after every ride...
Last edited by woodcraft; 10-21-19 at 10:12 AM.
#10
Senior Member
Join Date: Mar 2010
Location: Seattle, WA
Posts: 23,208
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 18883 Post(s)
Liked 10,646 Times
in
6,054 Posts
Having LBS do the glueing will save you a lot of headache. But flats can be very expensive. That Light Bicycle thread makes Chinese carbon hoops sound pretty attractive. Food for thought.
#11
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
If any of you are braking to the point of rim failure, your riding style needs to be addressed long before your equipment should be altered.
Likes For woodcraft:
#15
Senior Member
Thread Starter
Join Date: Jan 2011
Location: Pinehurst, NC, US
Posts: 1,716
Bikes: 2020 Trek Emonda SL6, 90's Vintage EL-OS Steel Bianchi with 2014 Campy Chorus Upgrade
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 452 Post(s)
Liked 162 Times
in
110 Posts
dave
#16
Veteran, Pacifist
Join Date: Dec 2004
Location: Seattle area
Posts: 13,332
Bikes: Bikes??? Thought this was social media?!?
Mentioned: 284 Post(s)
Tagged: 0 Thread(s)
Quoted: 3898 Post(s)
Liked 4,841 Times
in
2,232 Posts
Tubulars with a small amount of Stan's or OrangeSeal are extremely flat proof.
Tubular wheels are lighter.
Tubular tires from UK/EU suppliers ~ $65 if you wait for deals (VeloFlex Arenberg/Roubaix/Vlanderen).
Tubular tape is easy, if you don't wish to glue.
If you are serious about lightweight wheels, the problem with tubulars is IN YOUR HEAD.
High-end clinchers with latex tubes are super nice as well - and about the same price.
edit: Vittoria G+ tubulars for $49, Veloflex from $65.
https://www.merlincycles.com/road-bi...e_type=tubular
I think it's funny, guys riding $5000+ bikes, disc brakes, carbon wheels complaining a small price difference for tubulars as a reason not to convert.
Tubular wheels are lighter.
Tubular tires from UK/EU suppliers ~ $65 if you wait for deals (VeloFlex Arenberg/Roubaix/Vlanderen).
Tubular tape is easy, if you don't wish to glue.
If you are serious about lightweight wheels, the problem with tubulars is IN YOUR HEAD.
High-end clinchers with latex tubes are super nice as well - and about the same price.
edit: Vittoria G+ tubulars for $49, Veloflex from $65.
https://www.merlincycles.com/road-bi...e_type=tubular
I think it's funny, guys riding $5000+ bikes, disc brakes, carbon wheels complaining a small price difference for tubulars as a reason not to convert.
__________________
Vintage, modern, e-road. It is a big cycling universe.
Vintage, modern, e-road. It is a big cycling universe.
Last edited by Wildwood; 10-21-19 at 10:58 AM.
Likes For Wildwood:
Likes For woodcraft:
#18
Senior Member
Join Date: Oct 2018
Location: VA
Posts: 1,437
Bikes: SuperSix Evo | Revolt
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 733 Post(s)
Liked 815 Times
in
414 Posts
Just a few rollers Great ride, looking forward to doing it again next year!
FWIW, I'm on GP5K clinchers and they're great, fast and handle really well. I'm even running butyl tubes (Conti Race), I have a set of latex tubes that I'll try eventually (I've used them in my TT setup with good results).
Edit - I'm also on disc brakes, so braking doesn't factor into rim/tire choice, on alloys at the moment, but will get some carbons eventually.
#19
Senior Member
Why such good deals on tubular wheelsets? Two reasons off the top of my head... first, tubular rims are far easier to manufacture than clincher rims. The two 'hooks' on the clincher rim (required to hold on the tire) take a lot of brake heat, brake compressive (clamping) forces, forces from tire inflation, and road impacts. Lots of careful engineering, manufacturing and quality materials required to make these 'hooks'.
Tubular rims largely avoid these problems. Tubular rims are fundamentally superior, in terms of strength to weight, heat dissipation, isolation from tire inflation forces, ability to withstand brake compressive forces and impacts. Plus the rounder shape of the tubular rim profile avoids pinch flats.
The superior rim shape is why tubulars are used (exclusively) at the elite levels of the sport, past, present, and will be until the end of time.
So you can buy a new set of 1,400 gram aero carbon tubular wheels within minutes for less than $600. These wheels will be superior in every respect to any clincher (tubeless or otherwise) ever made or is possible of being made. Again: the two 'hooks' required to hold on clincher tires are the problem. They are heavy (rotating mass: at the worst place on a bike), fragile, and cause pinch flats.
Second reason: elite-level riding is done on tubulars. Except the rare short time trial where a top-name rider has garbage bags full of money dropped on them to ride a sponsor's (front only) clincher wheels. First name: Tony. Anyway, because racers have a rapid turnover of gear due to changing product lines and sponsorships, their high-end swag ends up heavily discounted on the second-hand market.
You want to be close to sponsored riders for their cast-offs; this is where you want to bottom-feed for tubular wheel cast-offs.
Hint: tubulars are almost impenetrable to flats if you pre-inject about 20cc of Stan's sealant. Make sure you get tires with removable valve cores. I have put big miles on some Tufo's this summer, with zero flats. I suspect that the cords on these tires will be showing before I flat these.
Tubular rims largely avoid these problems. Tubular rims are fundamentally superior, in terms of strength to weight, heat dissipation, isolation from tire inflation forces, ability to withstand brake compressive forces and impacts. Plus the rounder shape of the tubular rim profile avoids pinch flats.
The superior rim shape is why tubulars are used (exclusively) at the elite levels of the sport, past, present, and will be until the end of time.
So you can buy a new set of 1,400 gram aero carbon tubular wheels within minutes for less than $600. These wheels will be superior in every respect to any clincher (tubeless or otherwise) ever made or is possible of being made. Again: the two 'hooks' required to hold on clincher tires are the problem. They are heavy (rotating mass: at the worst place on a bike), fragile, and cause pinch flats.
Second reason: elite-level riding is done on tubulars. Except the rare short time trial where a top-name rider has garbage bags full of money dropped on them to ride a sponsor's (front only) clincher wheels. First name: Tony. Anyway, because racers have a rapid turnover of gear due to changing product lines and sponsorships, their high-end swag ends up heavily discounted on the second-hand market.
You want to be close to sponsored riders for their cast-offs; this is where you want to bottom-feed for tubular wheel cast-offs.
Hint: tubulars are almost impenetrable to flats if you pre-inject about 20cc of Stan's sealant. Make sure you get tires with removable valve cores. I have put big miles on some Tufo's this summer, with zero flats. I suspect that the cords on these tires will be showing before I flat these.
#20
Senior Member
Join Date: Mar 2010
Location: Seattle, WA
Posts: 23,208
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 18883 Post(s)
Liked 10,646 Times
in
6,054 Posts
People are talking about cost in this thread because that's important to @DaveLeeNC.
#21
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
Why such good deals on tubular wheelsets? Two reasons off the top of my head... first, tubular rims are far easier to manufacture than clincher rims. The two 'hooks' on the clincher rim (required to hold on the tire) take a lot of brake heat, brake compressive (clamping) forces, forces from tire inflation, and road impacts. Lots of careful engineering, manufacturing and quality materials required to make these 'hooks'.
Tubular rims largely avoid these problems. Tubular rims are fundamentally superior, in terms of strength to weight, heat dissipation, isolation from tire inflation forces, ability to withstand brake compressive forces and impacts. Plus the rounder shape of the tubular rim profile avoids pinch flats.
The superior rim shape is why tubulars are used (exclusively) at the elite levels of the sport, past, present, and will be until the end of time.
So you can buy a new set of 1,400 gram aero carbon tubular wheels within minutes for less than $600. These wheels will be superior in every respect to any clincher (tubeless or otherwise) ever made or is possible of being made. Again: the two 'hooks' required to hold on clincher tires are the problem. They are heavy (rotating mass: at the worst place on a bike), fragile, and cause pinch flats.
Second reason: elite-level riding is done on tubulars. Except the rare short time trial where a top-name rider has garbage bags full of money dropped on them to ride a sponsor's (front only) clincher wheels. First name: Tony. Anyway, because racers have a rapid turnover of gear due to changing product lines and sponsorships, their high-end swag ends up heavily discounted on the second-hand market.
You want to be close to sponsored riders for their cast-offs; this is where you want to bottom-feed for tubular wheel cast-offs.
Hint: tubulars are almost impenetrable to flats if you pre-inject about 20cc of Stan's sealant. Make sure you get tires with removable valve cores. I have put big miles on some Tufo's this summer, with zero flats. I suspect that the cords on these tires will be showing before I flat these.
Tubular rims largely avoid these problems. Tubular rims are fundamentally superior, in terms of strength to weight, heat dissipation, isolation from tire inflation forces, ability to withstand brake compressive forces and impacts. Plus the rounder shape of the tubular rim profile avoids pinch flats.
The superior rim shape is why tubulars are used (exclusively) at the elite levels of the sport, past, present, and will be until the end of time.
So you can buy a new set of 1,400 gram aero carbon tubular wheels within minutes for less than $600. These wheels will be superior in every respect to any clincher (tubeless or otherwise) ever made or is possible of being made. Again: the two 'hooks' required to hold on clincher tires are the problem. They are heavy (rotating mass: at the worst place on a bike), fragile, and cause pinch flats.
Second reason: elite-level riding is done on tubulars. Except the rare short time trial where a top-name rider has garbage bags full of money dropped on them to ride a sponsor's (front only) clincher wheels. First name: Tony. Anyway, because racers have a rapid turnover of gear due to changing product lines and sponsorships, their high-end swag ends up heavily discounted on the second-hand market.
You want to be close to sponsored riders for their cast-offs; this is where you want to bottom-feed for tubular wheel cast-offs.
Hint: tubulars are almost impenetrable to flats if you pre-inject about 20cc of Stan's sealant. Make sure you get tires with removable valve cores. I have put big miles on some Tufo's this summer, with zero flats. I suspect that the cords on these tires will be showing before I flat these.
#22
Senior Member
And what do you me by slowest? Differences between rolling resistance of various tires are trivial compared to aero effects and rotating mass. When you're trying to hang on in a fast group ride on a climb.. your tongue is rubbing on your front tire, and your heart is about to jump out of your chest. You have to stay with the pack, or you'll end up suffering solo for the next 10 miles. In this situation, low bike and especially wheel weight are the overwhelming need. This is where tubulars are the key advantage.
Who cares if your wheels are 10% more aero, as 95% of your riding time will be in the pack - sheltered from the wind.
BTW: large volume tires (such as 28mm+) have the worst aero and rolling resistence. They are definitely heavier. I tried some clinchers in 28's; between the porky rims and heavy tires they made my bike ride like a farm tractor.
#23
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
I got the tires for free. They refuse to die. I've resorted to daily high-speed runs on packed gravel on these 22mm tires. Still won't die.
And what do you me by slowest? Differences between rolling resistance of various tires are trivial compared to aero effects and rotating mass. When you're trying to hang on in a fast group ride on a climb.. your tongue is rubbing on your front tire, and your heart is about to jump out of your chest. You have to stay with the pack, or you'll end up suffering solo for the next 10 miles. In this situation, low bike and especially wheel weight are the overwhelming need. This is where tubulars are the key advantage.
Who cares if your wheels are 10% more aero, as 95% of your riding time will be in the pack - sheltered from the wind.
BTW: large volume tires (such as 28mm+) have the worst aero and rolling resistence. They are definitely heavier. I tried some clinchers in 28's; between the porky rims and heavy tires they made my bike ride like a farm tractor.
And what do you me by slowest? Differences between rolling resistance of various tires are trivial compared to aero effects and rotating mass. When you're trying to hang on in a fast group ride on a climb.. your tongue is rubbing on your front tire, and your heart is about to jump out of your chest. You have to stay with the pack, or you'll end up suffering solo for the next 10 miles. In this situation, low bike and especially wheel weight are the overwhelming need. This is where tubulars are the key advantage.
Who cares if your wheels are 10% more aero, as 95% of your riding time will be in the pack - sheltered from the wind.
BTW: large volume tires (such as 28mm+) have the worst aero and rolling resistence. They are definitely heavier. I tried some clinchers in 28's; between the porky rims and heavy tires they made my bike ride like a farm tractor.
#24
Senior Member
The only gaps occur during the climbs, at 10 miles per hour. Low profile carbon tubulars for the win.
#25
Globo Gym lifetime member
Join Date: Jan 2006
Location: Redmond, Oregon
Posts: 5,204
Bikes: Fast ones
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 410 Post(s)
Liked 614 Times
in
306 Posts
??? At 25mph, the hammerhead at the front of the pack is putting out 400 watts. At the back, we're eating little sandwiches and yakking about the movie we saw last night. 100 watts.
The only gaps occur during the climbs, at 10 miles per hour. Low profile carbon tubulars for the win.
The only gaps occur during the climbs, at 10 miles per hour. Low profile carbon tubulars for the win.
It doesn't sound like you have the experience or knowledge to be discussing this topic...
Likes For Cypress: