Removing minor marks on a carbon frame
#1
Junior Member
Thread Starter
Join Date: Jun 2021
Location: Nottingham
Posts: 9
Bikes: 2013 Boardman Sport. Just purchased a Raleigh SP Team frame I'm looking to build up from scratch.
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
Removing minor marks on a carbon frame
Morning
Wanted to pick peoples brains if possible or see if anyone else has done this. Got Carbon frame, which was I want to give a once over and looking good again. There are a few small marks/scratches that don't seem too deep on it that I want to try and polish/sand out. Was thinking about using wet and dry 2000/3000 paper to clear the marks and then hopefully I wouldn't have gone too deep to remove the clear coat and can simply polish afterwards.
Has anyone done this? What kind of results did you get?
Thanks
Wanted to pick peoples brains if possible or see if anyone else has done this. Got Carbon frame, which was I want to give a once over and looking good again. There are a few small marks/scratches that don't seem too deep on it that I want to try and polish/sand out. Was thinking about using wet and dry 2000/3000 paper to clear the marks and then hopefully I wouldn't have gone too deep to remove the clear coat and can simply polish afterwards.
Has anyone done this? What kind of results did you get?
Thanks
#2
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,945
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6173 Post(s)
Liked 4,790 Times
in
3,305 Posts
Just clean them out with some solvent. Acetone or xylene would be what I'd grab, since they are on my shelf. Be careful not to get it on the rest of the finish, unless you know what the rest of the finish is.
Apply some clear coat or color match and they'll probably pretty much disappear. Unless you think everyone is going to look as closely as you at your bike.
Apply some clear coat or color match and they'll probably pretty much disappear. Unless you think everyone is going to look as closely as you at your bike.
#3
Senior Member
Join Date: Aug 2012
Location: Los Alamitos, Calif.
Posts: 2,474
Bikes: Canyon Endurace
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1041 Post(s)
Liked 922 Times
in
539 Posts
I have a 2002 Trek 5200. It was in pretty bad shape when I got it. All the decals were torn and there were several minor nicks in the carbon frame but noth8ing severe enough to warrant any kind of repair. I can't remember exactly but I started out with something like 600 or 800 griit and then went 800 > 1000 > 1500 > 2000 then rubbing compound, polish and wax. I was very happy with the results. Don't' quote me on the exact grits that I used but I remember using somewhat of a sequence like above.
#4
Junior Member
Thread Starter
Join Date: Jun 2021
Location: Nottingham
Posts: 9
Bikes: 2013 Boardman Sport. Just purchased a Raleigh SP Team frame I'm looking to build up from scratch.
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
Thanks
Cheers. I'll give it a clean up using acetone first and then see what the state of play is after that.
#5
Senior Member
Join Date: Jul 2007
Posts: 7,569
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1851 Post(s)
Liked 678 Times
in
429 Posts
I had a carbon post that was glossy with decals. I didn't like how it looked on my matte frame and did not like the color of the decals, so I got light sandpaper and wet sanded it down to remove the decals and gloss. I then gave it a quick respray of clear matte paint.
It was fine. There was ample clear coat on there, so I never got to the actual carbon fiber.
Your frame probably has several layers of paint, but in sanding it, you may end up taking off all layers of paint, exposing the carbon. That isn't necessarily bad or dangerous, but it might not look good.
It was fine. There was ample clear coat on there, so I never got to the actual carbon fiber.
Your frame probably has several layers of paint, but in sanding it, you may end up taking off all layers of paint, exposing the carbon. That isn't necessarily bad or dangerous, but it might not look good.
#6
Senior Member
Join Date: Jun 2021
Location: Australia
Posts: 821
Bikes: 2002 Trek 5200 (US POSTAL), 2020 Canyon Aeroad SL
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 313 Post(s)
Liked 679 Times
in
327 Posts
I have a 2002 Trek 5200. It was in pretty bad shape when I got it. All the decals were torn and there were several minor nicks in the carbon frame but noth8ing severe enough to warrant any kind of repair. I can't remember exactly but I started out with something like 600 or 800 griit and then went 800 > 1000 > 1500 > 2000 then rubbing compound, polish and wax. I was very happy with the results. Don't' quote me on the exact grits that I used but I remember using somewhat of a sequence like above.
I've been pretty hesitant to take sandpaper to my bike thus far! I've got some small general wear marks on my 2002 5200 also that I wouldn't mind smoothing out.
#7
Senior Member
Join Date: Aug 2012
Location: Los Alamitos, Calif.
Posts: 2,474
Bikes: Canyon Endurace
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1041 Post(s)
Liked 922 Times
in
539 Posts
#8
Senior Member
Join Date: Jun 2021
Location: Australia
Posts: 821
Bikes: 2002 Trek 5200 (US POSTAL), 2020 Canyon Aeroad SL
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 313 Post(s)
Liked 679 Times
in
327 Posts
^ Looks fantastic! I've got a replacement decal set, so one day I might strip it down again and either sand out the imperfections or go the whole hog and have it resprayed.