Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

2 Questions on my QR Skewer

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

2 Questions on my QR Skewer

Old 07-09-19, 10:08 PM
  #1  
puma1552
Senior Member
Thread Starter
 
Join Date: Jul 2016
Posts: 666

Bikes: '17 Colnago C-RS (Full 5800); '16 Specialized Sirrus Elite

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Liked 32 Times in 21 Posts
2 Questions on my QR Skewer

1) See pic. Is this considered an internal cam skewer? I think it is, but just want to verify it's not an external cam skewer.

2) My rear QR skewer is not smooth upon closing or opening, it's just kinda jerky and not smooth (wheel is seated correctly, no junk in there, etc. - it just isn't a smooth acting lever like the front one). It does tighten up nice and holds the wheel nice and tight, no issues while riding, etc. - just doesn't have that satisfying smooth action when closing or opening, kinda stutters a bit. Anything to be concerned about here?


Last edited by puma1552; 07-09-19 at 10:30 PM.
puma1552 is offline  
Old 07-09-19, 11:27 PM
  #2  
cobba
Senior Member
 
Join Date: Aug 2006
Posts: 1,697
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 100 Post(s)
Likes: 0
Liked 8 Times in 8 Posts
Originally Posted by puma1552 View Post
1)Is this considered an internal cam skewer?
This article says it's a bit of a cross between internal and external.

https://bikerumor.com/2017/05/16/cam...r-wheelset-qr/


External cam skewer on top, internal cam skewer on bottom.



Last edited by cobba; 07-09-19 at 11:37 PM.
cobba is offline  
Likes For cobba:
Old 07-10-19, 12:05 AM
  #3  
Davet
Licensed Bike Geek
 
Davet's Avatar
 
Join Date: Oct 2002
Location: Los Barriles, Baja Sur, Mexico
Posts: 1,230

Bikes: Kirk Terraplane, Serotta Ottrott, Spectrum Super Custom, Hampsten Carbon Leger Tournesol

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 54 Post(s)
Liked 11 Times in 8 Posts
You might put just a dab of lube on the pivot and where the handle slides against the plate. That usually smooths things nicely.
Davet is offline  
Likes For Davet:
Old 07-10-19, 12:05 AM
  #4  
puma1552
Senior Member
Thread Starter
 
Join Date: Jul 2016
Posts: 666

Bikes: '17 Colnago C-RS (Full 5800); '16 Specialized Sirrus Elite

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Liked 32 Times in 21 Posts
It's not really exposed like an external cam; while it's not entirely enclosed either, the guts are pretty much within the body and I cannot see a washer the lever cradles into like you can with a typical external cam.

I figure this is either a pretty well protected external cam, or an internal cam that's a bit less protected than a typical one. I really don't know.

As for my quick release, I decided to go upstairs and open and close it 15-20 times, and it's nice and smooth now - I guess it just needed to be worked in a bit, so no issues there. Maybe it had been sitting around a while at the factory or something, but it's good now.

EDIT: @cobba thanks for posting that link, looks like it is indeed some weird hybrid skewer.

Last edited by puma1552; 07-10-19 at 12:10 AM.
puma1552 is offline  
Old 07-10-19, 01:47 AM
  #5  
canklecat
Me duelen las nalgas
 
canklecat's Avatar
 
Join Date: Aug 2015
Location: Texas
Posts: 9,456

Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel

Mentioned: 168 Post(s)
Tagged: 0 Thread(s)
Quoted: 2903 Post(s)
Liked 241 Times in 183 Posts
Some lightweight QRs like that, including my old Salsa external cam QRs, are made of aluminum (but not the skewers, which are steel) to save weight. Reportedly some may be titanium but I haven't seen any. They're usually found on weight weenie bikes like my early '90s Trek 5900, which was the lightest production bike ever made at that time. I eyeball bikes at group rides, including Tuesday's, and see a few external or hybrid QRs on carbon fiber and titanium bikes.

Galling (sorta similar to "stiction") can occur with aluminum parts under pressure and friction, which will tend to feel odd when camming under pressure, and can squeak or creak -- especially anodized aluminum parts. I use scented candle wax -- for some reason it seems to work better than oil or grease. It's just paraffin with a solvent that softens it a bit so it's easy to pinch off a bit with a fingertip and smudge it around friction surfaces like external cam QRs or between squeaky spokes.

Some folks don't trust external cam QRs but I don't see any mechanical reason why these won't hold as securely as hidden cam QRs. I wonder whether the bias is just resistance to changing from traditional doodads. So far my lightweight external cam QRs have held as securely as the more familiar steel hidden cam QRs.
canklecat is online now  
Old 07-10-19, 07:53 AM
  #6  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 31,587

Bikes: '''96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '12 Surly Pacer, All are 3x8,9 or 10. It is hilly around here!

Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1184 Post(s)
Likes: 0
Liked 46 Times in 41 Posts
Originally Posted by canklecat View Post
Some folks don't trust external cam QRs but I don't see any mechanical reason why these won't hold as securely as hidden cam QRs. I wonder whether the bias is just resistance to changing from traditional doodads. So far my lightweight external cam QRs have held as securely as the more familiar steel hidden cam QRs.
External cam skewers can't develop as much clamping force as internal cam skewers. For vertical rear dropouts and rim brake forks, that's not an issue as their clamping force is adequate. The problems arise in frames with horizontal dropouts or disc brake forks where their clamping force can be inadequate to keep the rear wheel positioned properly or keep the front wheel retained in the dropouts. The later then depends on the "lawyer's lips" for wheel retention.
HillRider is online now  
Old 07-10-19, 08:08 AM
  #7  
fietsbob 
coprolite
 
fietsbob's Avatar
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 41,396

Bikes: 8

Mentioned: 188 Post(s)
Tagged: 0 Thread(s)
Quoted: 6902 Post(s)
Liked 239 Times in 197 Posts
Exclusive to latest Campagnolo

Which few have , so as to be exact.. But ...

Make sure its tight,, * with vertical dropouts .. fork obviously is ,

rear wheel dropout un shown, probably too, as Indexing needs consistent wheel location .

Its not that big a deal..

* Lever Leaves a mark on the palm of your hand ...






...

Last edited by fietsbob; 07-10-19 at 08:11 AM.
fietsbob is offline  
Old 07-10-19, 09:07 AM
  #8  
Phil_gretz
Journeyman Bike Commuter
 
Phil_gretz's Avatar
 
Join Date: Aug 2009
Location: Alexandria, VA
Posts: 5,159

Bikes: '71 Jeunet 630, '79 Peugeot PXN10LE, '88 Fuji Saratoga, '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '16 Motobecane Gran Premio Elite, '18 Velobuild VB-R-022

Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 626 Post(s)
Liked 132 Times in 80 Posts
Put me down squarely in the camp of those who would not use that skewer. I'd replace with a Shimano skewer at the first opportunity. You can find the latest Ultegra skewers inexpensively if you know where to look.
Phil_gretz is offline  
Likes For Phil_gretz:
Old 07-12-19, 08:31 AM
  #9  
Sy Reene
Advocatus Diaboli
 
Sy Reene's Avatar
 
Join Date: Feb 2015
Location: Wherever I am
Posts: 4,839

Bikes: Merlin Cyrene, Nashbar steel CX

Mentioned: 10 Post(s)
Tagged: 1 Thread(s)
Quoted: 2291 Post(s)
Liked 46 Times in 44 Posts
Originally Posted by HillRider View Post
External cam skewers can't develop as much clamping force as internal cam skewers. For vertical rear dropouts and rim brake forks, that's not an issue as their clamping force is adequate. The problems arise in frames with horizontal dropouts or disc brake forks where their clamping force can be inadequate to keep the rear wheel positioned properly or keep the front wheel retained in the dropouts. The later then depends on the "lawyer's lips" for wheel retention.
I believe it's more correct to say that external cam skewers require more force to close in order to achieve the same clamping power as an internal cam skewer, but if you're not strength limited, either type of skewer can provide adequate clamping force.

As an aside question.. is there such a thing as using too much clamping force?
Sy Reene is offline  
Old 07-12-19, 08:39 AM
  #10  
trailangel
Senior Member
 
trailangel's Avatar
 
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 3,790

Bikes: Schwinn Varsity

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1361 Post(s)
Liked 95 Times in 63 Posts
Originally Posted by puma1552 View Post
It's not really exposed like an external cam; while it's not entirely enclosed either, the guts are pretty much within the body and I cannot see a washer the lever cradles into like you can with a typical external cam.

I figure this is either a pretty well protected external cam, or an internal cam that's a bit less protected than a typical one. I really don't know.

As for my quick release, I decided to go upstairs and open and close it 15-20 times, and it's nice and smooth now - I guess it just needed to be worked in a bit, so no issues there. Maybe it had been sitting around a while at the factory or something, but it's good now.

EDIT: @cobba thanks for posting that link, looks like it is indeed some weird hybrid skewer.
When my QR's don't work right I always threaten to take 'em upstairs......
trailangel is offline  
Old 07-12-19, 09:17 AM
  #11  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 31,587

Bikes: '''96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '12 Surly Pacer, All are 3x8,9 or 10. It is hilly around here!

Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1184 Post(s)
Likes: 0
Liked 46 Times in 41 Posts
Originally Posted by Sy Reene View Post
I believe it's more correct to say that external cam skewers require more force to close in order to achieve the same clamping power as an internal cam skewer, but if you're not strength limited, either type of skewer can provide adequate clamping force.
I'm not sure they can in a practical sense. Most external cam skewers have plastic cam seats and weaker lever pivots. They are made for light weight rather than strength. The lever force needed to equal the clamping force of an internal cam skewer would probably break them.
HillRider is online now  
Old 07-12-19, 09:19 AM
  #12  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 20,548

Bikes: Several, mostly not name brands.

Mentioned: 114 Post(s)
Tagged: 0 Thread(s)
Quoted: 1766 Post(s)
Liked 100 Times in 76 Posts
Originally Posted by Sy Reene View Post
I believe it's more correct to say that external cam skewers require more force to close in order to achieve the same clamping power as an internal cam skewer, but if you're not strength limited, either type of skewer can provide adequate clamping force.
Internal cam skewers have greater mechanical advantage than external cam skewers, and since the length of the lever arm is pretty much the same on each, it's harder to clamp an external cam skewer effectively on a horizontal dropout.

As an aside question.. is there such a thing as using too much clamping force?
You can exceed the strength of the component parts; e.g. I've seem broken aluminum external cam levers from using a leverage-enhancer ("cheater pipe," wrench, etc.) on the lever to get it to clamp properly on a horizontal dropout.
JohnDThompson is offline  
Old 07-12-19, 11:44 AM
  #13  
Sy Reene
Advocatus Diaboli
 
Sy Reene's Avatar
 
Join Date: Feb 2015
Location: Wherever I am
Posts: 4,839

Bikes: Merlin Cyrene, Nashbar steel CX

Mentioned: 10 Post(s)
Tagged: 1 Thread(s)
Quoted: 2291 Post(s)
Liked 46 Times in 44 Posts
Originally Posted by HillRider View Post
I'm not sure they can in a practical sense. Most external cam skewers have plastic cam seats and weaker lever pivots. They are made for light weight rather than strength. The lever force needed to equal the clamping force of an internal cam skewer would probably break them.
If you're breaking a skewer, you're applying too much force to close. Granted, I'm sure there are cheap and flimsy versions of external cam skewers -- just as there's probably on the market, a crappy version available of any type of bike component. My 4yr old Zipp external cam skewers have brass and steel parts. This shows up as one the most inexpensive skewers, but I don't see a real flaw in the design:
https://www.excelsports.com/main.asp...jor=1&minor=21

Originally Posted by JohnDThompson View Post
Internal cam skewers have greater mechanical advantage than external cam skewers, and since the length of the lever arm is pretty much the same on each, it's harder to clamp an external cam skewer effectively on a horizontal dropout.

You can exceed the strength of the component parts; e.g. I've seem broken aluminum external cam levers from using a leverage-enhancer ("cheater pipe," wrench, etc.) on the lever to get it to clamp properly on a horizontal dropout.
Yes, I think we all agree, internal cam skewers are easier to use to achieve a given clamping force. I'd also agree that for horizontal dropouts, an internal cam design makes a lot more sense. Though this isn't applicable to the OP.
Sy Reene is offline  
Old 07-12-19, 02:19 PM
  #14  
puma1552
Senior Member
Thread Starter
 
Join Date: Jul 2016
Posts: 666

Bikes: '17 Colnago C-RS (Full 5800); '16 Specialized Sirrus Elite

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Liked 32 Times in 21 Posts
So are we all in agreement these are odd hybrid skewers that neither fit definitions of internal or external? I have vertical dropouts and a lawyer tab fork, so I can't imagine I'll have problems using these...I'll also assume Campy did their due diligence in designing them...
puma1552 is offline  
Old 07-12-19, 02:33 PM
  #15  
caloso
Senior Member
 
caloso's Avatar
 
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 38,236

Bikes: Ridley Excalibur, Gazelle Champion Mondial, On-One Pompino, Specialized Rock Hopper

Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 1916 Post(s)
Liked 295 Times in 164 Posts
I've replaced all my external cam QRs with Ultegras. A few grams is totally worth the peace of mind.
caloso is online now  
Likes For caloso:
Old 07-12-19, 06:37 PM
  #16  
redlude97
Senior Member
 
Join Date: Sep 2011
Posts: 4,383
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1772 Post(s)
Liked 72 Times in 55 Posts
Same design as Boyd Wheel skewers, got close to 10,000 miles on a set that have been trouble free.
redlude97 is offline  
Old 07-28-19, 10:01 PM
  #17  
puma1552
Senior Member
Thread Starter
 
Join Date: Jul 2016
Posts: 666

Bikes: '17 Colnago C-RS (Full 5800); '16 Specialized Sirrus Elite

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Liked 32 Times in 21 Posts
Any real world pics of the Ultegra 6800 skewers? The interwebz tells me they are dark gray, which seems odd when Shimano running gear is either black or silver. Interwebz pics make it hard to get a feel for the color.

Also, is there an 8000 skewer? Can't seem to find any, not that skewers are probably top priority to redesign with each generation.
puma1552 is offline  
Old 07-28-19, 10:18 PM
  #18  
Davet
Licensed Bike Geek
 
Davet's Avatar
 
Join Date: Oct 2002
Location: Los Barriles, Baja Sur, Mexico
Posts: 1,230

Bikes: Kirk Terraplane, Serotta Ottrott, Spectrum Super Custom, Hampsten Carbon Leger Tournesol

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 54 Post(s)
Liked 11 Times in 8 Posts
Originally Posted by puma1552 View Post
Any real world pics of the Ultegra 6800 skewers? The interwebz tells me they are dark gray, which seems odd when Shimano running gear is either black or silver. Interwebz pics make it hard to get a feel for the color.

Also, is there an 8000 skewer? Can't seem to find any, not that skewers are probably top priority to redesign with each generation.
6800 skewers are dark grey. https://www.jensonusa.com/Shimano-Ul...-Quick-Release
Davet is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.