Leak at rim seam?
#1
Junior Member
Thread Starter
Leak at rim seam?
I bought a 29 front wheel with a wtb rim for a mullet setup and I attempted to set it up tubeless a couple days ago. It was a new wheel so I expected some leaks. I tracked the largest one down and it's coming from the seam where the rim is welded together.
I put ~4 Oz of sealant in and I've pumped it up a couple of times hoping the sealant would get it, but not happening.
So first of all, the wheel rim itself should not be leaking, right? Is that a defective rim?
And second, it's a pretty small seam, any thoughts on why the sealant isn't plugging it up?
I put ~4 Oz of sealant in and I've pumped it up a couple of times hoping the sealant would get it, but not happening.
So first of all, the wheel rim itself should not be leaking, right? Is that a defective rim?
And second, it's a pretty small seam, any thoughts on why the sealant isn't plugging it up?
#3
Junior Member
Thread Starter
#6
Senior Member
Sounds like a manufacturing defect, you should consider contacting the place from where you purchased the wheel - they should replace it with one that doesn’t leak. Welded joints aren’t supposed to leak.
#7
Senior Member
Join Date: Mar 2013
Location: Tucson Az
Posts: 1,679
Bikes: 2015 Ridley Fenix, 1983 Team Fuji, 2019 Marin Nail Trail 6
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 337 Post(s)
Liked 228 Times
in
138 Posts
Pinned wheels aren’t always welded. I had the same problem with my Stock Marin wheels, so I spent some time on YouTube, and the vids I saw said to use tape a couple of mm’s wider than the internal rim width. As soon as I replaced my tape per the vids, the problem went away.
the best were the vids from Stans.
the best were the vids from Stans.
#8
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
Where along the seam is it leaking? Is it right near the edge of the rim near the bead, or elsewhere? If it is not right near the bead I would suspect a taping issue.
Does the tape go right up to the walls of the rim? WTB recomends using tape a smidge wider than the internal width of the rim.
Does the tape go right up to the walls of the rim? WTB recomends using tape a smidge wider than the internal width of the rim.
#9
Junior Member
Thread Starter
Where along the seam is it leaking? Is it right near the edge of the rim near the bead, or elsewhere? If it is not right near the bead I would suspect a taping issue.
Does the tape go right up to the walls of the rim? WTB recomends using tape a smidge wider than the internal width of the rim.
Does the tape go right up to the walls of the rim? WTB recomends using tape a smidge wider than the internal width of the rim.
Annoying....
#10
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,906
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,932 Times
in
2,557 Posts
A possible concern - as you ride, centrifugal force will be doing its best to throw sealant away from the rim base toward the tire. I'm not a tubeless rider but if I were, I think I'd carry the appropriate tube with me for my first forays beyond walking/OK to call for sag distance. (And whatever tire irons that tire requires,)
#11
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,481
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 967 Post(s)
Liked 1,631 Times
in
1,047 Posts
A tube would fix this...
Just kidding. Apart from rim tape/sealant you may have identified a manufacturing defect. Not good...
Just kidding. Apart from rim tape/sealant you may have identified a manufacturing defect. Not good...
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)