1.25" or 2" Hitch Receiver for Bike Rack?
#1
Full Member
Thread Starter
Join Date: Jul 2017
Location: SoCal
Posts: 406
Bikes: Cannondale Carbon Synapse Road, Cannondale T2000 Touring, Vintage Mongoose IBOC Pro MTB, Vintage Peugeot 12spd racer, Old rusty Schwinn Manta Ray I neglected as a child, Diamondback Haanjo EXP Carbon & Metro, Specialized Roubaix Pro, RaleighSC Tandem
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 225 Post(s)
Liked 39 Times
in
29 Posts
1.25" or 2" Hitch Receiver for Bike Rack?
I'm contemplating the purchase of a platform bike rack for a vehicle. I have no plans on towing any trailers or anything of that nature
In light of this, would you recommend the 1.25 or 2 inch hitch receiver, and why?
Many thanks in advance!
In light of this, would you recommend the 1.25 or 2 inch hitch receiver, and why?
Many thanks in advance!
#2
Jedi Master
I've had both and would always prefer a 2" receiver unless there is something about the car that would prevent me from getting one.
Likes For kingston:
#4
Senior Member
Join Date: Jan 2007
Location: Eastern VA
Posts: 1,724
Bikes: 2022 Fuel EX 8, 2021 Domane SL6, Black Beta (Nashbar frame), 2004 Trek 1000C for the trainer
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 270 Post(s)
Liked 447 Times
in
266 Posts
I have 1-1/4 but then I have a Camry. My P/U truck has a 2 inch. But it’s a Quad cab with a loooong bed so I don’t need a hitch carrier.
#5
Senior Member
A 2" receiver will work with either a 2" or a 1 1/4 rack so there is no reason not to get a 2" if you have the option. Pretty much every 1 1/4 rack will come with an adapter to put in it a 2" receiver.
Likes For Canker:
#6
Junior Samples
I have a Forester that can't tow a dang thing, even though it is the Police Interceptor version.
Still, I put a 2" hitch on it. A platform rack will sway and pivot less in the larger receiver. I also have an anti-rattle bolt that tightens the rack into the receiver. It's similar to this one:
You thought I was kidding, din't ya?
Still, I put a 2" hitch on it. A platform rack will sway and pivot less in the larger receiver. I also have an anti-rattle bolt that tightens the rack into the receiver. It's similar to this one:
You thought I was kidding, din't ya?
#7
Junior Member
I own a forester also, and its good for towing 1500 lbs. I have a 2" Receiver for a bike rack, and I have a 5 foot by 8 foot aluminum, trailer I tow just fine with it for hauling lighter things. As canker stated, why not get a 2" and anything will fit it.
#8
Senior Member
Join Date: Sep 2017
Posts: 7,879
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 6963 Post(s)
Liked 10,963 Times
in
4,688 Posts
Bigger is better, other things equal. Get the 2".
Likes For Koyote:
#9
Junior Samples
Why the US version of the Forester is so puny, I've not a clue. It would seem to have something to do with regulations and not with mechanicals.
Doesn't make me no nevermind though. Mine tows nothing; the hitch is there just to hold a bike rack.
#10
Junior Member
Yup, and 1500 pounds is pretty minimal. I'd dang near max it out with a two-rail trailer with my two motorcycles and a gear box. The Euro version, IIRC, is at least 2000Kg. My wife's '18 Outback is 2700 pounds. Pretty much the same engine and transmission.
Why the US version of the Forester is so puny, I've not a clue. It would seem to have something to do with regulations and not with mechanicals.
Why the US version of the Forester is so puny, I've not a clue. It would seem to have something to do with regulations and not with mechanicals.
#11
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,519
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4353 Post(s)
Liked 3,993 Times
in
2,665 Posts
Always 2" if I can fit it. 1 1/4" if I am SOL. I would much rather have more load capacity and more rack capability.
#13
Senior Member
You don't need to be a structural engineer to answer that questions. Add to that the fact that 2" receivers cost almost the same as 1-1/4". And when you have larger racks for more bikes, they only come in 2" (for a reason...).
The questions is more why 1-1/4" even exists.
The questions is more why 1-1/4" even exists.
Likes For HerrKaLeun:
#14
Dirty Heathen
Join Date: Oct 2015
Location: MC-778, 6250 fsw
Posts: 2,182
Bikes: 1997 Cannondale, 1976 Bridgestone, 1998 SoftRide, 1989 Klein, 1989 Black Lightning #0033
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 889 Post(s)
Liked 906 Times
in
534 Posts
Yup, and 1500 pounds is pretty minimal. I'd dang near max it out with a two-rail trailer with my two motorcycles and a gear box. The Euro version, IIRC, is at least 2000Kg. My wife's '18 Outback is 2700 pounds. Pretty much the same engine and transmission.
Why the US version of the Forester is so puny, I've not a clue. It would seem to have something to do with regulations and not with mechanicals.
Doesn't make me no nevermind though. Mine tows nothing; the hitch is there just to hold a bike rack.
Why the US version of the Forester is so puny, I've not a clue. It would seem to have something to do with regulations and not with mechanicals.
Doesn't make me no nevermind though. Mine tows nothing; the hitch is there just to hold a bike rack.
As far as which reciever to use for a bike rack, get the 2" if it's available. There's more rack options in a 2" than the 1-1/2" (especially if you're shopping used racks) and it's more stable.
Most of the 1-1/2' racks are pretty light-duty, too, and typically don't have the fold-up or swing-away features of the 2" racks.
#15
Junior Samples
This went around on ADVrider once upon a time, IIRC it has to do with the EU/AUS requirements for trailers to have braking systems on much smaller trailers, that in the US are typically un-braked. So the 'EU' version of a car has a higher tow rating because EU trailers require less of the tow vehicle (and are typically towed at lower speeds)...
#16
Senior Member
Join Date: Aug 2017
Location: Northern Virginia
Posts: 727
Bikes: Current: 2016 Bianchi Volpe; 1973 Peugeot UO-8. Past: 1974 Fuji S-10-S with custom black Imron paint by Stinsman Racing of PA.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 215 Post(s)
Liked 204 Times
in
142 Posts
This is for two reasons,
1. some hitch makers will not warranty their hitch with a bike rack unless you use a top of the hitch post to the top of the liftgate or forward trunk gap to act as a support strap since the loaded racks can get bouncy when loaded (especially for more than one or two bikes; and;
2. on some vehicles with over the rear window spoilers on the liftgate, attaching such a strap can break the spoiler and high mount brake light. Those spoilers are usually plastic and are painted body color. Damage from the strap will require a replacement and repaint. I have seen this more on smaller receiver hitches and/or hitches that are recessed to be hidden when not in use.
I had a hitch all picked for my Santa Fe that did not lose ground clearance and was very discrete. Unfortunately, (or fortunately!) I read the online instructions and warranty and found out the hitch needed the support strap to carry the warranty.
#17
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18376 Post(s)
Liked 4,510 Times
in
3,352 Posts
I'd go by a combination of your car and your expected load. So, for a small car with 1L to 2L engine, and 1 or 2 bikes, then go with the Class 1 or Class 2 (1 1/4") hitch rated at 2000 to 3500 lbs and 200 to 350 lbs tongue weight.
If you have a small SUV or pickup with a 2.8L or larger engine, go with a full Class III or Class IV hitch (2") rated at 6,000 to 12,000 lbs and 600 to 1200 lbs tongue weight.
And, of course, the more bikes (3 or 4 bikes?) the larger the hitch.
The twisting motion of a bike might be a little different than a trailer, but either size should be fine if the rack is constructed properly.
If you have a small SUV or pickup with a 2.8L or larger engine, go with a full Class III or Class IV hitch (2") rated at 6,000 to 12,000 lbs and 600 to 1200 lbs tongue weight.
And, of course, the more bikes (3 or 4 bikes?) the larger the hitch.
The twisting motion of a bike might be a little different than a trailer, but either size should be fine if the rack is constructed properly.
#18
Senior Member
Join Date: May 2014
Location: Treasure Coast, FL
Posts: 987
Bikes: 2014 Cannondale Supersix EVO 3, 2015 Trek 520, 2017 Bike Friday Pocket Rocket, 2022 Moots Vamoots Disc RSL
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 285 Post(s)
Liked 267 Times
in
140 Posts
I've always enjoyed driving small cars and I just need to transport two bikes, so I went with a 1.25 instead of the 2. My little Mazda 3 is not rated for any significant towing, nor do I have any desire to do so. My Kuat NV 2.0 two bicycle rack requires only a 1.25 hitch and also swings out so I can open the hatch door with bicycles on it. I couldn't be happier. I would have needed a 2.0 hitch if I purchased the four bicycle Kuat rack.
#19
Senior Member
Two inch will be more stable even if you don't care about weight limits.
#20
Full Member
Thread Starter
Join Date: Jul 2017
Location: SoCal
Posts: 406
Bikes: Cannondale Carbon Synapse Road, Cannondale T2000 Touring, Vintage Mongoose IBOC Pro MTB, Vintage Peugeot 12spd racer, Old rusty Schwinn Manta Ray I neglected as a child, Diamondback Haanjo EXP Carbon & Metro, Specialized Roubaix Pro, RaleighSC Tandem
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 225 Post(s)
Liked 39 Times
in
29 Posts
Thanks everybody!
2 inch it is!
2 inch it is!
Likes For michaelm101:
#21
staring at the mountains
Join Date: Mar 2005
Location: Castle Pines, CO
Posts: 4,560
Bikes: Obed GVR, Fairdale Goodship, Salsa Timberjack 29
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 394 Post(s)
Liked 197 Times
in
112 Posts
Your car's towing capability will dictate this more than anything else. You didn't say what your vehicle is?
For example, my 2013 A3 had to be a 1 1/4 hitch because that's what the car is rated for towing (Class I). My 2015 Q5 has a 2" hitch because it can tow more (Class III).
Go to etrailer.com and plug in your vehicle's specs. Go from there. This isn't one of those debates like 27.5 vs 29 or disc vs calipers. You go with what your vehicle can accommodate.
For example, my 2013 A3 had to be a 1 1/4 hitch because that's what the car is rated for towing (Class I). My 2015 Q5 has a 2" hitch because it can tow more (Class III).
Go to etrailer.com and plug in your vehicle's specs. Go from there. This isn't one of those debates like 27.5 vs 29 or disc vs calipers. You go with what your vehicle can accommodate.
#22
Senior Member
Join Date: Mar 2011
Posts: 3,094
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1034 Post(s)
Liked 1,290 Times
in
743 Posts
I can only get a 1 1/4 inch receiver on my current vehicle, and my last one. I have a two bike rack from Thule, and have had no issues, including multiple 800+ mile day trips. With a 1 1/4 inch receiver you are limited to a two bike rack. Other than that, it is no issue. Just get a good receiver. The receiver made for my vehicle by Curt, required a special strap if a bicycle rack was used. The receiver I bought, from Reese did not, as the Hidden Hitch receiver for my last receiver also did not require a strap.
Of course if a vehicle can accept a 2 inch receiver, go with that, you can then use 1 1/4 or 2 inch.
Of course if a vehicle can accept a 2 inch receiver, go with that, you can then use 1 1/4 or 2 inch.
#23
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18376 Post(s)
Liked 4,510 Times
in
3,352 Posts
I'm sure I could get a 2" or a 2 1/2" receiver attached to my Fiat 500 that I'm building up now. But, that would be pretty pointless. I may tow a trailer with it, but doubt there would be much need to exceed 3500 lbs tow, 350 lbs tongue CAT 2, and I don't think I could trust the car frame for much more than that. Certainly not pulling without trailer brakes.
Likes For CliffordK:
#24
Senior Member
Join Date: Mar 2011
Posts: 3,094
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1034 Post(s)
Liked 1,290 Times
in
743 Posts
I'm sure I could get a 2" or a 2 1/2" receiver attached to my Fiat 500 that I'm building up now. But, that would be pretty pointless. I may tow a trailer with it, but doubt there would be much need to exceed 3500 lbs tow, 350 lbs tongue CAT 2, and I don't think I could trust the car frame for much more than that. Certainly not pulling without trailer brakes.
#25
Senior Member
Join Date: Apr 2015
Location: Metro Detroit/AA
Posts: 8,207
Bikes: 2016 Novara Mazama
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 3640 Post(s)
Liked 81 Times
in
51 Posts
If you can fit it, 2". I have a 1-1/4" on the ST cause that is all that will fit with the center exhaust, I hate it.