Problem with front derailleur
#1
Junior Member
Thread Starter
Join Date: Aug 2019
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Problem with front derailleur
Hi,
I've got this weird issue when the chain is brushing against the front derailleur when I'm set to either lowest or highest rear gear. This started happening after my wheels got nicked and I had to buy new ones along with a freewheel casette.
Any ideas why this might've started happening?
Cheers!
I've got this weird issue when the chain is brushing against the front derailleur when I'm set to either lowest or highest rear gear. This started happening after my wheels got nicked and I had to buy new ones along with a freewheel casette.
Any ideas why this might've started happening?
Cheers!
Last edited by matlev; 08-10-19 at 08:43 AM.
#2
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
Hi,
I've got this weird issue when the chain is bruising against the front derailleur when I'm set to either lowest or highest rear gear. This started happening after my wheels got nicked and I had to buy new ones along with a freewheel casette.
Any ideas why this might've started happening?
Cheers!
I've got this weird issue when the chain is bruising against the front derailleur when I'm set to either lowest or highest rear gear. This started happening after my wheels got nicked and I had to buy new ones along with a freewheel casette.
Any ideas why this might've started happening?
Cheers!
Likes For matlev:
#4
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
Anytime you put different wheels on or a different freewheel cassette (**********) you need to re-adjust your derailleurs. Have you done this?
#5
Senior Member
Join Date: Nov 2015
Location: Dublin, Ireland
Posts: 1,268
Bikes: Bianchi Ti Megatube; Colnago Competition; Planet-X EC-130E; Klein Pulse; Amp Research B4; Litespeed Catalyst; Trek Y11
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 605 Post(s)
Liked 480 Times
in
260 Posts
Must be a slightly different hub spacing on the new wheels causing a change in the chain line. Try adjusting your upper and lower limit screws on the FD a quarter turn, not enough to throw your chain either way, but enough to stop it rubbing as you approach the limits.
#6
Junior Member
Thread Starter
Join Date: Aug 2019
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Must be a slightly different hub spacing on the new wheels causing a change in the chain line. Try adjusting your upper and lower limit screws on the FD a quarter turn, not enough to throw your chain either way, but enough to stop it rubbing as you approach the limits.
#8
Senior Member
Join Date: Nov 2015
Location: Dublin, Ireland
Posts: 1,268
Bikes: Bianchi Ti Megatube; Colnago Competition; Planet-X EC-130E; Klein Pulse; Amp Research B4; Litespeed Catalyst; Trek Y11
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 605 Post(s)
Liked 480 Times
in
260 Posts
Before you go to that extreme, try disconnecting everything and starting from scratch. (You'd have to do this anyway with any new FD.) Realign it w/the cranks, make sure it's all the correct angle & height, re-check your limit screws, clean & lube everything really good... and why not, make sure the rear wheel is correctly seated in the dropouts... and go from there.
Likes For ridelikeaturtle:
#9
Junior Member
Thread Starter
Join Date: Aug 2019
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Before you go to that extreme, try disconnecting everything and starting from scratch. (You'd have to do this anyway with any new FD.) Realign it w/the cranks, make sure it's all the correct angle & height, re-check your limit screws, clean & lube everything really good... and why not, make sure the rear wheel is correctly seated in the dropouts... and go from there.
#10
Senior Member
Join Date: Nov 2015
Location: Dublin, Ireland
Posts: 1,268
Bikes: Bianchi Ti Megatube; Colnago Competition; Planet-X EC-130E; Klein Pulse; Amp Research B4; Litespeed Catalyst; Trek Y11
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 605 Post(s)
Liked 480 Times
in
260 Posts
If it's misaligned, it can be touching / rubbing in different places at the extremes.
It worked before you changed wheels, logically it should be able to work again.
It worked before you changed wheels, logically it should be able to work again.
#12
Senior Member
Most front derailleurs have screws which adjust the lower and upper travel limits. If other posters are correct and the chain line has changed you may need to adjust these so that both allow a little more travel along with adjusting cable tension.
#13
Full Member
Join Date: Nov 2016
Location: SoCal
Posts: 489
Bikes: 2014 Bruce Gordon Rock&Road, 1995 Santana Visa Tandem, 1990 Trek 520, 2012 Surly LHT
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 211 Post(s)
Likes: 0
Liked 43 Times
in
35 Posts
Not to be difficult but it seems we are missing lots of information. First is are the shifters friction or indexed? With the old wheel did you have to trim the FD to keep itfrom rubbbing? Are you able to trim the FD with the new wheel? How many speeds front and rear?
#14
Senior Member
Join Date: Jun 2019
Posts: 580
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 254 Post(s)
Likes: 0
Liked 182 Times
in
141 Posts
I would also check that the FD is lined up straight. If it got turned a bit so it's at an angle relative the the chain, that can cause rubbing on both ends. And I agree with Eggman84 - a bit more info on the type of derailleur, levers and gear setup would be helpful.