Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

I need some pantographing done

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

I need some pantographing done

Old 05-26-20, 08:15 PM
  #1  
speedevil 
I never finish anyth
Thread Starter
 
speedevil's Avatar
 
Join Date: Jul 2010
Location: Western KY
Posts: 1,105

Bikes: 2008 Merckx LXM, 2003 Giant XTC mtb, 2001 Lemond Alpe d'Huez, 1997 Lemond Zurich, 1989 Cannondale ST, 1988 Masi Nuovo Strada, 1983 Pinarello Turismo

Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 290 Post(s)
Liked 109 Times in 73 Posts
I need some pantographing done

I have a 3T stem on my Pinarello that is pantographed "Pinarello" but it is too short for a decent fit. I found a replacement that will work, but before I replace the current stem I'd like to have the new stem pantographed.

The current stem should be usable as a model. it is pantographed on both sides.

Anyone?


__________________
Dale, NL4T
speedevil is offline  
Old 05-26-20, 09:44 PM
  #2  
rhm
multimodal commuter
 
rhm's Avatar
 
Join Date: Nov 2006
Location: NJ, NYC, LI
Posts: 19,381

Bikes: 1940s Fothergill, 1959 Allegro Special, 1963? Claud Butler Olympic Sprint, Lambert 'Clubman', 1974 Fuji "the Ace", 1976 Holdsworth 650b conversion rando bike, 1983 Trek 720 tourer, 1984 Counterpoint Opus II, 1993 Basso Gap, 2010 Downtube 8h, and...

Mentioned: 483 Post(s)
Tagged: 0 Thread(s)
Quoted: 1692 Post(s)
Liked 154 Times in 115 Posts
See if you can make contact with the guy who runs Cyclomondo CYCLOMONDO - BICYCLE RESTORATION DECALS. He's in Australia. He was doing pantographing for a while. I see it's no longer on his website, so I assume it wasn't economical or something, but he would definitely be able to tell you what's involved. I've never had any contact with him, though, so I dunno what he'll say, if anything.
__________________
I put new leather on ruined saddles like Brooks, etc. You can reach me by private message.
rhm is offline  
Old 05-27-20, 12:23 AM
  #3  
Last ride 76 
1/2 as far in 2x the time
 
Last ride 76's Avatar
 
Join Date: Nov 2013
Location: Northern Bergen County, NJ
Posts: 1,838

Bikes: Yes, Please.

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 475 Post(s)
Liked 242 Times in 193 Posts
Originally Posted by speedevil View Post
I have a 3T stem on my Pinarello that is pantographed "Pinarello" but it is too short for a decent fit. I found a replacement that will work, but before I replace the current stem I'd like to have the new stem pantographed.

The current stem should be usable as a model. it is pantographed on both sides.

Anyone?


I have a 120ish (double outline letters) Pinarello pantographed stem if you're interested...
__________________
I seem to have lost what little mind I had left before this all started.
Last ride 76 is offline  
Old 05-27-20, 01:19 AM
  #4  
verktyg 
verktyg
 
verktyg's Avatar
 
Join Date: Jul 2006
Location: SF Bay Area
Posts: 3,352

Bikes: Current favorites: 1988 Peugeot Birraritz, 1984 Gitane Super Corsa, 1981 Bianchi Campione Del Mondo, 1992 Paramount OS, 1990 Bianchi Mondiale, 1988 Colnago Technos, 1985 RalieghUSA Team Pro, 1973 Holdsworth

Mentioned: 159 Post(s)
Tagged: 0 Thread(s)
Quoted: 712 Post(s)
Liked 354 Times in 237 Posts
Simple local solution: find a business that does engraving like a trophy shop.

It could also be done on a CNC milling machine that has an engraving program.

It's probably going to cost you because of the set up time to do an individual part.

verktyg
__________________
Things aren't always what they seem... Don't believe everything you think!

Chas. ;-)
verktyg is offline  
Old 05-27-20, 01:27 AM
  #5  
P!N20
Senior Member
 
P!N20's Avatar
 
Join Date: Aug 2010
Posts: 1,008
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 456 Post(s)
Liked 335 Times in 226 Posts
Cyclo Retro in Melbourne, Australia do some amazing work: https://www.cycloretro.com/

Maybe cost prohibitive with postage, but hey, the exchange rate is on your side.
P!N20 is offline  
Old 05-27-20, 03:14 AM
  #6  
nomadmax 
Senior Member
 
Join Date: Jun 2018
Location: SW Ohio
Posts: 1,449
Mentioned: 91 Post(s)
Tagged: 0 Thread(s)
Quoted: 660 Post(s)
Liked 694 Times in 368 Posts
Originally Posted by P!N20 View Post
Cyclo Retro in Melbourne, Australia do some amazing work: https://www.cycloretro.com/

Maybe cost prohibitive with postage, but hey, the exchange rate is on your side.
That right there ^. Says 75 bucks (I'm guessing Australian) and no set up fee. I wonder if it's 75 bucks a side though?
nomadmax is offline  
Old 05-27-20, 03:51 AM
  #7  
bwilli88 
Senior Member
 
bwilli88's Avatar
 
Join Date: Jan 2013
Location: Kampong Cham, Cambodia but I have quite a few in Lancaster, PA
Posts: 2,246

Bikes: Bikes in USA; 73 Raleigh Supercourse dingle speed, 74 Raleigh Grand Prix SS, 78 Raleigh Supercourse, 83 Centurion Pro-Tour, 82 Raleigh RRA.

Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 578 Post(s)
Liked 178 Times in 124 Posts
Cycloretro lists $150 for a Stem 2 sides.
bwilli88 is offline  
Likes For bwilli88:
Old 05-27-20, 07:08 AM
  #8  
RobbieTunes 
Half drunk? Finish!
 
RobbieTunes's Avatar
 
Join Date: Dec 2007
Location: Very Southern Indiana
Posts: 26,360
Mentioned: 34 Post(s)
Tagged: 1 Thread(s)
Quoted: 378 Post(s)
Liked 940 Times in 594 Posts
Originally Posted by bwilli88 View Post
Cycloretro lists $150 for a Stem 2 sides.
How long is yours? A pantomime stem on my Piní would be cool
__________________

I have unfinished business.

RobbieTunes is offline  
Old 05-27-20, 07:47 AM
  #9  
speedevil 
I never finish anyth
Thread Starter
 
speedevil's Avatar
 
Join Date: Jul 2010
Location: Western KY
Posts: 1,105

Bikes: 2008 Merckx LXM, 2003 Giant XTC mtb, 2001 Lemond Alpe d'Huez, 1997 Lemond Zurich, 1989 Cannondale ST, 1988 Masi Nuovo Strada, 1983 Pinarello Turismo

Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 290 Post(s)
Liked 109 Times in 73 Posts
@RobbieTunes, kind of a personal question. The stem is 70mm.
__________________
Dale, NL4T
speedevil is offline  
Old 05-27-20, 12:27 PM
  #10  
rccardr 
aka: Dr. Cannondale
 
rccardr's Avatar
 
Join Date: Jul 2009
Posts: 5,906

Bikes: Lots. Just...lots.

Mentioned: 169 Post(s)
Tagged: 0 Thread(s)
Quoted: 1290 Post(s)
Liked 375 Times in 202 Posts
Touch base with fellow BF’er Stephen Needles. Guy does it as a hobby. He’s in England, which makes shipping rather pricey, but does incredible work.
Have a couple pieces being shipped back, can provide pics when they arrive...to be mounted on a VERY SPECIAL Grail-level acquisition that is otherwise complete.
__________________
Hard at work in the Secret Underground Laboratory...
rccardr is online now  
Old 05-27-20, 12:46 PM
  #11  
Wildwood
Veteran/Pacifist/Resister
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 9,917

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 218 Post(s)
Tagged: 0 Thread(s)
Quoted: 2315 Post(s)
Liked 777 Times in 483 Posts
subscribed -
any Puget Sound pantographers?


edit: could use some DeRosa, Merckx, Mondia. Maybe others.
Price sounds within the 'gift request budget' that my kids set for b'day and xmas prezzies.
they often have easy arms for twisting.

Last edited by Wildwood; 05-27-20 at 12:56 PM.
Wildwood is offline  
Old 05-27-20, 02:41 PM
  #12  
Big Block
Senior Member
 
Join Date: Jan 2010
Location: Adelaide, Australia
Posts: 686
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 154 Post(s)
Liked 23 Times in 18 Posts
Originally Posted by bwilli88 View Post
Cycloretro lists $150 for a Stem 2 sides.
that is Australian dollars, so around $US100
and postage calculator is at https://auspost.com.au/parcels-mail/...mPostcode=3000
also in $A
Big Block is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.