Matte to Glossy
#3
Junior Member
Thread Starter
#4
Senior Member
Join Date: Jan 2013
Location: South Jersey
Posts: 2,262
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 713 Post(s)
Liked 796 Times
in
473 Posts
That's how base/clear paints work. The base color is flat and the clear provides the gloss. I wouldn't try it with a rattlecan clear, because the results will not be great or durable. Best results will be achieved with a catalyzed clear over a properly prepared surface.
#6
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
If you try this, make certain that the wax does not contain silicones if you think you might want to paint it later. It is very difficult to remove silicones and you are likely to get fisheye or orange peel defects if you try to paint over silicone-containing paint.
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,053
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4194 Post(s)
Liked 3,837 Times
in
2,295 Posts
I'll also add that not all "paint" is agreeable with low cost rattle can stuff. Powder coating is an example of a finish that won't accept enamels. The clear coat will go on and dry but will flake off soon enough. Before adding a different brand/sourcing of paint on top of a preexisting finish do your homework or be willing to end up with a result that is even worse then before you started. Andy
__________________
AndrewRStewart
AndrewRStewart
#8
Banned
Powder coat an exception, Prep is taking all the original finish off..
#9
Junior Member
Thread Starter
#10
Junior Member
Thread Starter
Good info.
#11
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,800
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1943 Post(s)
Liked 2,163 Times
in
1,322 Posts
Maybe someone has actually polished a matte bike frame. I haven’t, but I can tell you about polishing ukuleles. I have some ukuleles. I have polished the satin finish tops on a few of them; even used a car buffer on one.
I was able to get a nice gloss, but it was not the same deep gloss as the finish on my guitars and other ukes that have a sprayed gloss finish. They look like a hand rubbed gloss; which is okay for an instrument finish. The areas around the neck and bridge are difficult to polish. The back of the neck actually looks better; those who play will understand, which means maybe after 50 or 100 hours.
I can’t imagine polishing a matte bike finish, especially where the tubes meet, and getting any decent result remotely close to a painted gloss finish. And once you start you can’t go back.
John
I was able to get a nice gloss, but it was not the same deep gloss as the finish on my guitars and other ukes that have a sprayed gloss finish. They look like a hand rubbed gloss; which is okay for an instrument finish. The areas around the neck and bridge are difficult to polish. The back of the neck actually looks better; those who play will understand, which means maybe after 50 or 100 hours.
I can’t imagine polishing a matte bike finish, especially where the tubes meet, and getting any decent result remotely close to a painted gloss finish. And once you start you can’t go back.
John
Likes For 70sSanO:
#12
Senior Member
To paint a frame glossy, first clean thoroughly with mineral spirits and clean new rags, or special wipes, made for this purpose. Use 800 grit wet sandpaper or grey extra fine scotch brite to scuff every bit of the surface. Wear nitrile gloves to avoid finger oils getting on the frame. The frame must be very clean and lightly tack ragged to insure no lint on the surface.
Catalyzed gloss clear urethane paint is sold in spray cans. Once the catalyst is introduced, the paint must be used within a limited time. I'd get two cans. Start with fork, to get some practice before moving on to the frame.
Catalyzed gloss clear urethane paint is sold in spray cans. Once the catalyst is introduced, the paint must be used within a limited time. I'd get two cans. Start with fork, to get some practice before moving on to the frame.