Slipping seatpost, HELP!
#1
Junior Member
Thread Starter
Slipping seatpost, HELP!
So, I have the Cannondale Trail 5 2020 bike, alloy frame and alloy 31.6mm seatpost with a standard quick release seat clamp. I am having a big issue recently, which is slipping seatpost.
Well, everything was OK since I bought the bike in February. I adjusted the height of seatpost after buying and all good. Recently, last week, it was the first time I completely removed the seatpost and cleaned it with a cloth as it had dirt. And the seatpost had scratches too.
I put a very thin of lithium grease so that next time it does not stuck in the frame. i applied the grease below the label of minimum insertion. I put it back, tightened the quick release with a normal force which I used to do before.
While riding, I noticed it slipped gradually after some time by 2 or 3 centimeters. I put it up again, and tightened a bit harder. It was OK but slipped by 1 centimeter only.
I retightened it again and rode some offtrack, and it slipped by 2 centimeters after some time. This was frustrating. So, I overtightened it more and it slipped by just 1 or 2 millimeters instead of centimeters.
I came back home, removed the seatpost and seat clamp as well. I inspected the frame and all good. No sign of defect etc. I sprayed the quick release with penetrating oil from Abro to eliminate corrosion or whatever. I removed the lithium grease and applied standard grease. Yes, a thin layer. I cleaned the seat tube inside a bit with a cloth. I put it back again and this time, almost overtightened the quick release. I did not test it yet. Maybe it will work or not, soon will know.
So, what are the solutions I can apply if it slips again?
1/ Should I change clamp to a bolt one?
2/ Is it slipping because of the scratches on the seatpost?
3/ Should I tighten it with more amount of force?
I am afraid to overtight it. Maybe overtightening it will work too. But I still want to use normal pressure. I'm considering buying a seat clamp with bolt. Maybe that quick release is crap.
Well, everything was OK since I bought the bike in February. I adjusted the height of seatpost after buying and all good. Recently, last week, it was the first time I completely removed the seatpost and cleaned it with a cloth as it had dirt. And the seatpost had scratches too.
I put a very thin of lithium grease so that next time it does not stuck in the frame. i applied the grease below the label of minimum insertion. I put it back, tightened the quick release with a normal force which I used to do before.
While riding, I noticed it slipped gradually after some time by 2 or 3 centimeters. I put it up again, and tightened a bit harder. It was OK but slipped by 1 centimeter only.
I retightened it again and rode some offtrack, and it slipped by 2 centimeters after some time. This was frustrating. So, I overtightened it more and it slipped by just 1 or 2 millimeters instead of centimeters.
I came back home, removed the seatpost and seat clamp as well. I inspected the frame and all good. No sign of defect etc. I sprayed the quick release with penetrating oil from Abro to eliminate corrosion or whatever. I removed the lithium grease and applied standard grease. Yes, a thin layer. I cleaned the seat tube inside a bit with a cloth. I put it back again and this time, almost overtightened the quick release. I did not test it yet. Maybe it will work or not, soon will know.
So, what are the solutions I can apply if it slips again?
1/ Should I change clamp to a bolt one?
2/ Is it slipping because of the scratches on the seatpost?
3/ Should I tighten it with more amount of force?
I am afraid to overtight it. Maybe overtightening it will work too. But I still want to use normal pressure. I'm considering buying a seat clamp with bolt. Maybe that quick release is crap.
#2
Senior Member
Join Date: Aug 2006
Location: Valley Forge: Birthplace of Freedom
Posts: 1,299
Bikes: Novara Safari, CAAD9, WABI Classic, WABI Thunder
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 366 Post(s)
Liked 457 Times
in
240 Posts
I have clean and slightly roughened the first inch of seat tube with sandpaper. They sell some seat post lube with grit in it also.
A friend of mine used a second collar that used an allen key on top of the first.
A friend of mine used a second collar that used an allen key on top of the first.
#3
Banned
Likes For fietsbob:
#4
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
Good advice^^
I have also 'knurled' the seatpost with a punch where I think the clamp grabs the most. I bunch of punch marks around the post. Also clean out all the grease, degrease and use carbon fiber assembly paste... has grit in the paste. Also... get a better clamp... I like Salsa brand clamps.
I have also 'knurled' the seatpost with a punch where I think the clamp grabs the most. I bunch of punch marks around the post. Also clean out all the grease, degrease and use carbon fiber assembly paste... has grit in the paste. Also... get a better clamp... I like Salsa brand clamps.
#5
Senior Member
Join Date: Feb 2017
Location: Hollister, CA (not the surf town)
Posts: 1,737
Bikes: 2019 Specialized Roubaix Comp Di2, 2009 Roubaix, early 90's Giant Iguana
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 643 Post(s)
Liked 1,526 Times
in
551 Posts
Try using anti-seize instead of grease. Available at your local auto parts store or good hardware store.
Likes For Ogsarg:
#6
Senior Member
Join Date: Dec 2015
Location: Norcal
Posts: 207
Bikes: Moots Vamoots RSL 2018, Passoni Titanio 2020
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 33 Times
in
8 Posts
I highly recommend: https://www.parktool.com/product/sup...compound-sac-2
#7
Senior Member
Join Date: Sep 2013
Location: Massachusetts
Posts: 4,530
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 2112 Post(s)
Liked 663 Times
in
443 Posts
Owner's Manual
Please read your owner's manual (especially p. 26, and p. 75, but the rest too) and/or contact your dealer.
Excerpts:
-mr. bill
Please read your owner's manual (especially p. 26, and p. 75, but the rest too) and/or contact your dealer.
Excerpts:
Originally Posted by Cannondale
1. Ask your dealer to help you make sure you
know how to correctly clamp your seat post.
2. Understand and apply the correct technique
for clamping your seat post
know how to correctly clamp your seat post.
2. Understand and apply the correct technique
for clamping your seat post
Originally Posted by Cannondale
If you can fully close the cam lever without
wrapping your fingers around the seat post or a
frame tube for leverage, and the lever does not
leave a clear imprint in the palm of your hand,
the tension is insufficient. Open the lever; turn
the tension adjusting nut clockwise a quarter
turn; then try again.
wrapping your fingers around the seat post or a
frame tube for leverage, and the lever does not
leave a clear imprint in the palm of your hand,
the tension is insufficient. Open the lever; turn
the tension adjusting nut clockwise a quarter
turn; then try again.
Originally Posted by Cannondale
■ Seat Post Lubrication Clean and apply the following to a seat post before inserting into the frame.
- Is a gel like lubricant formulated for use with carbon fiber components (Cannondale p/n KF115/).
- Alloy Seat Tube & Alloy Seat Post = Grease
- Alloy Seat Tube & Carbon Post = Carbon Gel
- Carbon Seat Tube & Alloy Seat Post = Carbon Gel
- Carbon Seat Tube & Carbon Seat Post = Carbon Gel
- Is a gel like lubricant formulated for use with carbon fiber components (Cannondale p/n KF115/).
Last edited by mr_bill; 07-13-20 at 03:15 PM.
#9
Banned
I have a folding bike, seat post pushed down locks the fold, so It has to be QR, in my case they're stacked so I open both levers @ once..
#10
Junior Member
Thread Starter
#11
Junior Member
Thread Starter
Owner's Manual
Please read your owner's manual (especially p. 26, and p. 75, but the rest too) and/or contact your dealer.
Excerpts:
-mr. bill
Please read your owner's manual (especially p. 26, and p. 75, but the rest too) and/or contact your dealer.
Excerpts:
-mr. bill
Likes For alij2018:
#13
Junior Member
Thread Starter
You sandpaper last inch at the bottom fully until the entire paint came off? What this will do?
#14
Banned
#15
Junior Member
Thread Starter
#17
Senior Member
Join Date: Aug 2007
Posts: 2,595
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 608 Post(s)
Liked 352 Times
in
225 Posts
Good advice here but really the bike is under warranty and this shouldn't be your problem to fix. You shouldn't have to purchase a new seat post clamp or anti-seize or knurled the seat post. It is fine if you want to but I would be taking the bike back to the bicycle shop where you bought it and have them deal with it.
#18
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,389
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,971 Times
in
1,918 Posts
Clean the goop off from both areas & smear some extra hold hair gel on the post. Tighten it down & let it sit for 30 minutes while you clean your chain, wheels, & check psi while also getting the mail. After 30 minutes, your seat should stay at height. To remove the seat post, loosen the flange of all its tension, & with a rapid twisting motion while lifting up, it should remove freely. Cleaning & Reapplying gel is needed when the hardware tension has been released.
__________________
-Oh Hey!
-Oh Hey!
#19
Senior Member
Join Date: Sep 2013
Location: Massachusetts
Posts: 4,530
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 2112 Post(s)
Liked 663 Times
in
443 Posts
Crazy thought. Are you actually riding down trails now that the weather is nice? Get out of the saddle. (I would think this is self teaching on hard-tails, hell, self teaching on any tails, but....)
-mr. bill
-mr. bill
#20
Senior Member
As is so often the case, the answer may be beer. Drink a can, then cut a strip of the aluminum can approx. 1/2" wide and 2' long. Use this as a shim to firm up the clamp's grip on the post.
Good luck
Good luck
#22
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,636
Bikes: Merlin Cyrene, Nashbar steel CX
Mentioned: 14 Post(s)
Tagged: 1 Thread(s)
Quoted: 4733 Post(s)
Liked 1,532 Times
in
1,003 Posts
I highly recommend: https://www.parktool.com/product/sup...compound-sac-2
#23
Banned
Frame's seat tube 31.8? , seat post 27.2?
these look excellent : https://www.sjscycles.co.uk/seat-pos...18-mm/?geoc=US
these look excellent : https://www.sjscycles.co.uk/seat-pos...18-mm/?geoc=US
#24
Senior Member
Join Date: Sep 2013
Location: Massachusetts
Posts: 4,530
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 2112 Post(s)
Liked 663 Times
in
443 Posts
Can we just file this as yet another “Everything worked great until I 'fixed' it” thread?
-mr. bill
-mr. bill
Last edited by mr_bill; 07-15-20 at 12:08 PM.