Less Than A Week To Fix This
#1
Junior Member
Thread Starter
Join Date: Feb 2018
Location: Mountain View CA
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Less Than A Week To Fix This
Hey all,
I have a trip to CO coming up in 6 days and my bike is broken. There is a small metal mating surface on the rear right dropout that has broken out and now the wheel skews and rubs on the frame.
I have fashioned a replacement and have tried Super Glue and a Loctite Epoxy that sets in about 6min, is ok to handle in 20 and cures fully in 24 hours. We neither will hold the piece in place. I used a chrome washer with a ton of dremel work and the frame is carbon fiber.
What type of glue/adhesive would you use?
I have been getting this bike ready for this trip for a bit. New wheel, seat, bars, stem, large chainring, chain, rear derailleur and cassette. I would hate to not be able to bring it with me. The idea of renting a bike sounds like a hassle and expensive. The bike manufacturer is sending me a new frame but it won't arrive for a few days and it will be really hard for me to get it taken apart and rebuilt, not to mention expensive, before I leave.
Help?
(It would be easier to help if I could post pics but I have to go on a posting binge to get above 10 posts apparently. )
I have a trip to CO coming up in 6 days and my bike is broken. There is a small metal mating surface on the rear right dropout that has broken out and now the wheel skews and rubs on the frame.
I have fashioned a replacement and have tried Super Glue and a Loctite Epoxy that sets in about 6min, is ok to handle in 20 and cures fully in 24 hours. We neither will hold the piece in place. I used a chrome washer with a ton of dremel work and the frame is carbon fiber.
What type of glue/adhesive would you use?
I have been getting this bike ready for this trip for a bit. New wheel, seat, bars, stem, large chainring, chain, rear derailleur and cassette. I would hate to not be able to bring it with me. The idea of renting a bike sounds like a hassle and expensive. The bike manufacturer is sending me a new frame but it won't arrive for a few days and it will be really hard for me to get it taken apart and rebuilt, not to mention expensive, before I leave.
Help?
(It would be easier to help if I could post pics but I have to go on a posting binge to get above 10 posts apparently. )
#2
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,394
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,979 Times
in
1,920 Posts
Take it to a shop that works with cf fiberglass?
__________________
-Oh Hey!
-Oh Hey!
#3
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,094
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4209 Post(s)
Liked 3,875 Times
in
2,315 Posts
Having already altered the surfaces I suspect any repair is not going to be a quickie, or one that I would trust on a multy day tour without prior testing. No good info or photos prevent more speculation. Andy
__________________
AndrewRStewart
AndrewRStewart
#5
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,563 Times
in
1,026 Posts
This may be repairable, or it may be a sign that the frame has failed and is absolutely not safe to ride.
In general terms, if you wanted to fashion a replacement for missing carbon fiber, you'd want to use another fiber and epoxy. Chromed metal doesn't take to glue. You can use carbon fiber, glass fiber or even thin cotton cloth after degreasing all surfaces and fibers. The strength of the added piece will come from its fiber density.
In general terms, if you wanted to fashion a replacement for missing carbon fiber, you'd want to use another fiber and epoxy. Chromed metal doesn't take to glue. You can use carbon fiber, glass fiber or even thin cotton cloth after degreasing all surfaces and fibers. The strength of the added piece will come from its fiber density.
#6
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,847
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,827 Times
in
1,543 Posts
If the manufacturer is sending you a new frame (assuming warranty and free) then what you have is probably broken badly and probably dangerously.
Colorado has mountains, you don't want a frame breaking or a wheel popping loose and jamming in the frame in the mountains.
Based on current info (no picture) conservative approach is don't ride the frame.
Colorado has mountains, you don't want a frame breaking or a wheel popping loose and jamming in the frame in the mountains.
Based on current info (no picture) conservative approach is don't ride the frame.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#7
Thrifty Bill
Join Date: Jan 2008
Location: Mountains of Western NC
Posts: 23,526
Bikes: 86 Katakura Silk, 87 Prologue X2, 88 Cimarron LE, 1975 Sekai 4000 Professional, 73 Paramount, plus more
Mentioned: 96 Post(s)
Tagged: 0 Thread(s)
Quoted: 1236 Post(s)
Liked 964 Times
in
628 Posts
Six days is plenty of time to swap parts to a good frame. One day job.
#9
Senior Member
Wait for the new frame, swap parts. It's less than a one day job. I'd even replace the cables too.
There is no way I'd take a bodged repair like that on a week long tour.
There is no way I'd take a bodged repair like that on a week long tour.
#11
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
Fabrication on the washer is impressive but riding it is not worth the risk.
The last ambulance ride I took cost $1119 and I only spent 36 hours in the hospital. No trip is worth even that.
The last ambulance ride I took cost $1119 and I only spent 36 hours in the hospital. No trip is worth even that.
#12
Senior Member
#13
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,563 Times
in
1,026 Posts
While you certainly could fill that spot in with something that will last under compression, you haven't fixed the problem of how much weaker that area is due to losing a huge chunk of what makes the structural connection between wheel and bike. You'd have to be nuts to ride that down a mountainside.
#14
Senior Member
Note that the CF has not been compromised; it's still as intact as before. The part that fell off is metal insert that provides scuff protection for the CF. The repair washer replaces that function just like before. Any 2-part epoxy works for holding the pieces together. Since lateral-load is in compression from QR-skewer, it really doesn't matter what you use as long as it holds metal insert. Heck, even double-sided tape or bubble-gum will be fine.
Vertical loading from weight goes upward into structure same as before.
Vertical loading from weight goes upward into structure same as before.
#15
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,847
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,827 Times
in
1,543 Posts
Note that the CF has not been compromised; it's still as intact as before. The part that fell off is metal insert that provides scuff protection for the CF. The repair washer replaces that function just like before. Any 2-part epoxy works for holding the pieces together. Since lateral-load is in compression from QR-skewer, it really doesn't matter what you use as long as it holds metal insert. Heck, even double-sided tape or bubble-gum will be fine.
Vertical loading from weight goes upward into structure same as before.
Vertical loading from weight goes upward into structure same as before.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#16
Senior Member
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702
Bikes: old clunker
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 105 Times
in
83 Posts
Note that the CF has not been compromised; it's still as intact as before. The part that fell off is metal insert that provides scuff protection for the CF. The repair washer replaces that function just like before. Any 2-part epoxy works for holding the pieces together. Since lateral-load is in compression from QR-skewer, it really doesn't matter what you use as long as it holds metal insert. Heck, even double-sided tape or bubble-gum will be fine.
Vertical loading from weight goes upward into structure same as before.
Vertical loading from weight goes upward into structure same as before.
I'd ride it. The piece that fell off was only bonded on and thus only slightly structural. The skewer will keep everything in place. Just inspect frequently.
#17
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,563 Times
in
1,026 Posts
Note that the CF has not been compromised; it's still as intact as before. The part that fell off is metal insert that provides scuff protection for the CF. The repair washer replaces that function just like before. Any 2-part epoxy works for holding the pieces together. Since lateral-load is in compression from QR-skewer, it really doesn't matter what you use as long as it holds metal insert. Heck, even double-sided tape or bubble-gum will be fine.
Vertical loading from weight goes upward into structure same as before.
Vertical loading from weight goes upward into structure same as before.
And the OP has ridden this bike with other stuff substituted and the wheel came out - how do you know the wheel popping out at an angle didn't do damage to both dropouts?
#18
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
I'd probably use the skewer to clamp, and epoxy that washer into place, and try it out.
Probably not a life and death risk. So, if the wheel pops out, and rubs the chainstays???
The issue would be whether or not I'd be comfortable taking it on a multi-day trip. I'd probably prefer taking it a few days around the neighborhood, but part of the decision will depend on how isolated one will be, and how harmful a day or so of downtime could be.
Be aware that frame mods might affect any warranty coverage, if that is an issue.
#19
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,563 Times
in
1,026 Posts
Aside from the hanger, there should be some right/left symmetry, so if the left has some kind of inserts on both sides, then the right probably did too.
I'd probably use the skewer to clamp, and epoxy that washer into place, and try it out.
Probably not a life and death risk. So, if the wheel pops out, and rubs the chainstays???
The issue would be whether or not I'd be comfortable taking it on a multi-day trip. I'd probably prefer taking it a few days around the neighborhood, but part of the decision will depend on how isolated one will be, and how harmful a day or so of downtime could be.
Be aware that frame mods might affect any warranty coverage, if that is an issue.
I'd probably use the skewer to clamp, and epoxy that washer into place, and try it out.
Probably not a life and death risk. So, if the wheel pops out, and rubs the chainstays???
The issue would be whether or not I'd be comfortable taking it on a multi-day trip. I'd probably prefer taking it a few days around the neighborhood, but part of the decision will depend on how isolated one will be, and how harmful a day or so of downtime could be.
Be aware that frame mods might affect any warranty coverage, if that is an issue.
#20
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
As mentioned above, chrome may be a slippery surface, and perhaps stainless would have been better. Make sure the surface of both pieces is roughened slightly.
I probably wouldn't choose superglue for an app like this, and if it failed, it needs to be 100% cleaned off of both surfaces.
One issue might be load application. It shouldn't take much to hold the washer in place with a compression load from the skewer.
However, a vertical load from the axle setting on the washer may be bad (or forward from the chain tension). So, it might be beneficial to undercut the washer slightly, and perhaps also build up the dropout slightly with epoxy, or even a fiber reinforced epoxy.
I probably wouldn't choose superglue for an app like this, and if it failed, it needs to be 100% cleaned off of both surfaces.
One issue might be load application. It shouldn't take much to hold the washer in place with a compression load from the skewer.
However, a vertical load from the axle setting on the washer may be bad (or forward from the chain tension). So, it might be beneficial to undercut the washer slightly, and perhaps also build up the dropout slightly with epoxy, or even a fiber reinforced epoxy.
#21
Senior Member
Obviously poor prep as it was originally epoxied on from factory. From photo of washer, it doesn't have sufficient epoxy behind it. You should see it oozing out at edges, a sign that all gaps and voids between washer and dropout has been filled.
I've done this repair on numerous frames, starting with aluminium frames back in '80s. On some frames, washer have pins that goes through dropout and are welded to washer on other side.
I've done this repair on numerous frames, starting with aluminium frames back in '80s. On some frames, washer have pins that goes through dropout and are welded to washer on other side.
#22
Senior Member
As mentioned above, chrome may be a slippery surface, and perhaps stainless would have been better. Make sure the surface of both pieces is roughened slightly.
I probably wouldn't choose superglue for an app like this, and if it failed, it needs to be 100% cleaned off of both surfaces.
One issue might be load application. It shouldn't take much to hold the washer in place with a compression load from the skewer.
However, a vertical load from the axle setting on the washer may be bad (or forward from the chain tension). So, it might be beneficial to undercut the washer slightly, and perhaps also build up the dropout slightly with epoxy, or even a fiber reinforced epoxy.
I probably wouldn't choose superglue for an app like this, and if it failed, it needs to be 100% cleaned off of both surfaces.
One issue might be load application. It shouldn't take much to hold the washer in place with a compression load from the skewer.
However, a vertical load from the axle setting on the washer may be bad (or forward from the chain tension). So, it might be beneficial to undercut the washer slightly, and perhaps also build up the dropout slightly with epoxy, or even a fiber reinforced epoxy.
#23
Senior Member
How many miles have all of us ridden with insufficiently tight or completely loosened QR skewers?
You don't need much below axle-centreline. That extra amount below is really to allow QR to clamp on parallel surfaces.
Last edited by DannoXYZ; 06-27-18 at 02:45 AM.
#24
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,563 Times
in
1,026 Posts
Obviously poor prep as it was originally epoxied on from factory. From photo of washer, it doesn't have sufficient epoxy behind it. You should see it oozing out at edges, a sign that all gaps and voids between washer and dropout has been filled.
I've done this repair on numerous frames, starting with aluminium frames back in '80s. On some frames, washer have pins that goes through dropout and are welded to washer on other side.
I've done this repair on numerous frames, starting with aluminium frames back in '80s. On some frames, washer have pins that goes through dropout and are welded to washer on other side.
And even if it is bonded properly, it needs to be entirely perpendicular to the lucknut, or the force of the skewer is going to squeeze it out sideways from the locknut pushing on one side more than the other.
I'm not surprised this didn't work - I'm surprised that the original metal part bonded to a carbon dropout lasted any time at all. If the OP insists on repairing this, make the washer out of fiberglass so it can flex with the underlying carbon in the dropout and so the resin matrix in the fiber provides a good bond to the matrix in the dropout.
But I still think having your hub pop out of dropout is more potential destruction than I'd trust on a bike that will be climbing and descending.
#25
Junior Member
Thread Starter
Join Date: Feb 2018
Location: Mountain View CA
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I will try with more Epoxy. I am also thinking that the epoxy I got, even though new, was somehow bad as the mix I made didn't harden more than 24 hours later. It was rubbery.
I prepped the metal with a little grinding and the carbon with some acetone and some brushing. I made the spacer a bit smaller to reduce the chance it will have a vertical pressure applied to it. The frame itself looks ok - no cracking that I can see but I will reinspect.
I hear the concerns and respect them. I did some checking and can't find a bike to rent in Denver atm. Well I did but they want $700.
I prepped the metal with a little grinding and the carbon with some acetone and some brushing. I made the spacer a bit smaller to reduce the chance it will have a vertical pressure applied to it. The frame itself looks ok - no cracking that I can see but I will reinspect.
I hear the concerns and respect them. I did some checking and can't find a bike to rent in Denver atm. Well I did but they want $700.