Remove freewheel from unmounted hub
#1
Newbie
Thread Starter
Join Date: Jul 2020
Posts: 47
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 15 Post(s)
Likes: 0
Liked 6 Times
in
3 Posts
Remove freewheel from unmounted hub
Hi there
Does anyone have an idea to best loosen a freewheel from a hub that is not mounted in a wheel.
I have tried using a chain whip but no luck. I have tried fixing the body with a bunch of cable ties, well that didnt work either
i have also tried loosening the lockring but after approx two turns the lockring seizes. Not coming off.
Any help would be grateful.
Does anyone have an idea to best loosen a freewheel from a hub that is not mounted in a wheel.
I have tried using a chain whip but no luck. I have tried fixing the body with a bunch of cable ties, well that didnt work either
i have also tried loosening the lockring but after approx two turns the lockring seizes. Not coming off.
Any help would be grateful.
#2
Senior Member
Join Date: Sep 2005
Location: Oakland, CA
Posts: 3,265
Bikes: '82 Univega Competizione, '72 Motobecane Grand Record, '83 Mercian KOM Touring, '85 Univega Alpina Uno, '76 Eisentraut Limited
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,205 Times
in
701 Posts
I have seen a technique where you use a bunch of old spokes placed through the drive-side spoke holes to build up enough material for a "handle" as you gather them all in one bunch. Google "remove freewheel bare hub" and the first results will be a couple of Youtube videos from RJ the Bike Guy. He makes good videos for basic maintenance stuff and for vexing problems like this.
#3
Senior Member
Join Date: May 2008
Location: North, Ga.
Posts: 2,401
Bikes: 3Rensho-Aerodynamics, Bernard Hinault Look - 1986 tour winner, Guerciotti, Various Klein's & Panasonic's
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 159 Post(s)
Liked 375 Times
in
162 Posts
Is it possible to unscrew the smallest cog? Maybe you can remove the cogs individually and lace up the wheel to get at the hub body. All brands are different. Many have large cogs that screw of the back of the body and that is a bummer.
A guy on Facebook recently posted a frame contraption he made that allowed him to lace all the spoke holes with wire. It allowed him to release the freewheel body. Good luck!
A guy on Facebook recently posted a frame contraption he made that allowed him to lace all the spoke holes with wire. It allowed him to release the freewheel body. Good luck!
#4
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,881
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Mentioned: 140 Post(s)
Tagged: 0 Thread(s)
Quoted: 1452 Post(s)
Liked 2,185 Times
in
961 Posts
Only the top two sprockets are threaded to the body, IIRC, and the remaining four are splined and slip off.
Did you turn the retaining ring clockwise to loosen? It does have reverse threads.
Is your intention to save the freewheel or the hub? Or both? Depending on your answer I have different solutions which might solve your conundrum!
Did you turn the retaining ring clockwise to loosen? It does have reverse threads.
Is your intention to save the freewheel or the hub? Or both? Depending on your answer I have different solutions which might solve your conundrum!
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
#5
Senior Member
Join Date: Nov 2010
Location: Magnolia State, 100° with 110% humidity
Posts: 1,230
Bikes: American, Italian, and Japanese.. in no particular order.
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
Quoted: 350 Post(s)
Liked 276 Times
in
128 Posts
Just to expound on this, I inserted a few old spokes through both sides of the hub. I clamped the spokes in a bench vise and also placed a wooden block under the hub to act as cushion so as not to mar or flatten the hub flange on the vise jaws.
#6
Senior Member
I was in just this same dilemma last week! I picked up an unlaced Maxicar hub with a Suntour NW freewheel. iBOB discussion here.
Basically the biggest recommendation was to re-lace the drive-side of the wheel, even just crudely, into a rim. In my case, this would have required removing the cogs since the large cog obstructed the spoke holes from getting fed spokes.
In the end, I removed the cogs, but instead of lacing the wheel I filed a channel across the inner freewheel body using a dremel with variously sized cutoff wheels, taking great care to avoid grinding into the hub threads or any other part of the hub, then "cracked" the freewheel body open with a cold chisel. Once cracked, the diameter of the body's threads increases slightly so the threads dissociate from the hub threads. I was then able to just spin it off by hand. You can see in the pics how close I came to the hub threads without actually touching them, and you can see the cracks from forcing it open with the chisel. It was like playing Operation when I was a kid! (Only the stakes were higher).
EDIT to add: after getting the cogs off, I first tried immobilizing the hub on a large block of wood using a handful of spokes laced into the hub and passing through small holes in the block, then bent 90 degrees so they sat flat against the underside of the block, and clamped them there, but no go... the torque on the freewheel body just pulled the spokes right out of the block like spaghetti!
Basically the biggest recommendation was to re-lace the drive-side of the wheel, even just crudely, into a rim. In my case, this would have required removing the cogs since the large cog obstructed the spoke holes from getting fed spokes.
In the end, I removed the cogs, but instead of lacing the wheel I filed a channel across the inner freewheel body using a dremel with variously sized cutoff wheels, taking great care to avoid grinding into the hub threads or any other part of the hub, then "cracked" the freewheel body open with a cold chisel. Once cracked, the diameter of the body's threads increases slightly so the threads dissociate from the hub threads. I was then able to just spin it off by hand. You can see in the pics how close I came to the hub threads without actually touching them, and you can see the cracks from forcing it open with the chisel. It was like playing Operation when I was a kid! (Only the stakes were higher).
EDIT to add: after getting the cogs off, I first tried immobilizing the hub on a large block of wood using a handful of spokes laced into the hub and passing through small holes in the block, then bent 90 degrees so they sat flat against the underside of the block, and clamped them there, but no go... the torque on the freewheel body just pulled the spokes right out of the block like spaghetti!
Last edited by southpawboston; 01-19-21 at 03:00 PM.
Likes For southpawboston:
#7
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
If you have a friend who’s into machining, or a fabrication shop that seems friendly, ask If they can set your hub up in the chuck of a lathe for the time it takes to undo the f/w.
I’ve also heard good things about using an impact wrench to break loose f/w and cassette lockrings. Supposedly it can be enough to hold the hub by hand.
I’ve also heard good things about using an impact wrench to break loose f/w and cassette lockrings. Supposedly it can be enough to hold the hub by hand.
Last edited by dabac; 01-19-21 at 03:10 PM.
#8
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
You can take a bunch of spokes, and temporarily lace the NDS of the hub to a rim (doesn't need to be a specific size rim or in good condition). THen put the FW remover on the hub and hold it in place with the QR, put the remover in a bench vise and use the temporarily installed rim for leverage to loosen the FW as if it was a complete wheel.
NB. When doing the temporary 'lacing' of the rim to the hub, you needn't do any crosses or any other techniques required to make a rideable wheel.
NB. When doing the temporary 'lacing' of the rim to the hub, you needn't do any crosses or any other techniques required to make a rideable wheel.
#9
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
i have nothing to add towards a method, but i'd like to suggest a product called "freeze off" i've used on separating dissimilar metals with mostly good results. available at o'reilly, atleast
#10
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,940
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 115 Post(s)
Tagged: 0 Thread(s)
Quoted: 1300 Post(s)
Liked 1,900 Times
in
1,136 Posts
It appears that you can get spokes into the drive side through the free wheel. If so do that. Lacing into the non drive side risks splitting the hub in the center from the torque needed to break the free wheel. 9 spokes should be enough to get a rim laced for free wheel removal. If you can get 18 spokes in then even better. As long as all of the spokes are the same length you should get enough purchase to remove the free wheel by locking the removal tool in a vise and turning the rim. Good Luck I had to cut a body off a rather nice hub three weeks ago with not so good results. HTH, Smiles, MH
#11
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,881
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Mentioned: 140 Post(s)
Tagged: 0 Thread(s)
Quoted: 1452 Post(s)
Liked 2,185 Times
in
961 Posts
southpawboston Great work in saving the hub and sacrificing a PIA freewheel design! It probably helps, that in my experience, the New Winner freewheel bodies were made with very brittle steel. They tend not to deform but instead have pieces crack off.
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Likes For pastorbobnlnh:
#12
Senior Member
Join Date: Feb 2020
Posts: 2,812
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1105 Post(s)
Likes: 0
Liked 1,326 Times
in
782 Posts
If you want to save both bits you'll have to re-lace it, even the drive side. Z-bend spokes are the answer; if necessary get a smaller rim, say 24", and a bunch of old spokes from a larger wheel. Figure out what length spoke fits the hub and small rim, and cut the heads off and make your Z-bend at more-or-less the right distance. It does not have to be more than close, the wheel does not have to be true. Lace the wheel, remove as usual. Save the spokes and rim for the next time.
Likes For oneclick:
#13
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,421
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 971 Post(s)
Liked 624 Times
in
399 Posts
Photo in post #1 is a high flange hub; could a u-shaped tool be made from a bar and two bolts to project through the holes in the hub, hold that in a vise, and remove freewheel normally? Kind of a giant version of the two-pin tools used on adjustable cups for a bottom bracket.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#14
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,827 Times
in
1,995 Posts
Photo in post #1 is a high flange hub; could a u-shaped tool be made from a bar and two bolts to project through the holes in the hub, hold that in a vise, and remove freewheel normally? Kind of a giant version of the two-pin tools used on adjustable cups for a bottom bracket.
the freewheel has already suffered from an incorrect tool. In my view- it might be worth more than the hub.
The cogs look in decent shape, and it MIGHT be french threaded... (nope, English, that makes it easier)
in the old days we had a shop tool that bent a zig zag into a spoke, lace the wheel provisionally with a dented rim and remove as normal.
This all depends on the correct remover.
If you wish to save the hub, confirm threading type and confirm condition of the cones, no reason to spend energy on a bad hub.
#15
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,499
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2740 Post(s)
Liked 3,388 Times
in
2,051 Posts
A couple of threads dealing with freehub but gives you some ideas.
https://www.bikeforums.net/bicycle-m...b-removal.html
https://www.bikeforums.net/bicycle-m...laced-hub.html
https://www.bikeforums.net/bicycle-m...b-removal.html
https://www.bikeforums.net/bicycle-m...laced-hub.html
#16
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
Photo in post #1 is a high flange hub; could a u-shaped tool be made from a bar and two bolts to project through the holes in the hub, hold that in a vise, and remove freewheel normally? Kind of a giant version of the two-pin tools used on adjustable cups for a bottom bracket.
and, if there's not a pulley tool to fit, maybe fashion a two or three pin (using bolts) spanner to engage the flange holes behind the freewheel cluster and use a long breaker bar on the freewheel tool. that's what i'd do.
edit: yeah, shoot.....i've got a headset spanner made of flat steel about 1/8 in thick. with a spanner like that, drill some holes, put in bolts.....boom!....that would work
#17
Newbie
Thread Starter
Join Date: Jul 2020
Posts: 47
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 15 Post(s)
Likes: 0
Liked 6 Times
in
3 Posts
Spoiler
I have seen a technique where you use a bunch of old spokes placed through the drive-side spoke holes to build up enough material for a "handle" as you gather them all in one bunch. Google "remove freewheel bare hub" and the first results will be a couple of Youtube videos from RJ the Bike Guy. He makes good videos for basic maintenance stuff and for vexing problems like this.
Is your intention to save the freewheel or the hub? Or both? Depending on your answer I have different solutions which might solve your conundrum!
#18
curmudgineer
Join Date: Dec 2009
Location: Chicago SW burbs
Posts: 4,417
Bikes: 2 many 2 fit here
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 263 Post(s)
Liked 112 Times
in
70 Posts
thook is on to something. In conjunction with any/all of the above, try putting the whole works in the freezer for a while then re-attempt separation.
#19
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,421
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 971 Post(s)
Liked 624 Times
in
399 Posts
...and we might have found yet another reason that high-flange hubs are better.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#20
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,881
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Mentioned: 140 Post(s)
Tagged: 0 Thread(s)
Quoted: 1452 Post(s)
Liked 2,185 Times
in
961 Posts
If your preference is to save the hub, removing the sprockets and outer body will provide plenty of space to facilitate a temporary lacing of the hub to a rim for leverage. You then have a choice of using the removal tool and attempting a salvage of the freewheel or use a pipe wrench to grab the inner body. Attempting the second option could damage the inner body and thus ruin the freewheel.
Before attempting either of the above, try heating the inner body with a torch first. The expansion of the steel body from the aluminum hub threads might provide some help.
Best of luck!
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
#21
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
#22
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
Spoiler
thanks for all your replies.
A bit embarrassing but I was actually looking at RJ's channel to find a solution as I also find him very informative. I tried his method of creating some Z-Bend spokes and lacing the NDS. Worked really good but the damn thing is ridiculously tight. Will have to try with some leverage later on.
I would like to save both but have a slight feeling that the freewheel will be toast as I cant remove the lockring. And yes, loosened it by going clockwise.
oh, and the freezer suggestion by old's'cool....it's also a good idea. leave it in several hours/overnight. you need the expansion and contraction to relieve the surface tension on the threading. a torch, while it will very likely work, will destroy the freewheel. a freezer is also more readily available...hopefully
Last edited by thook; 01-20-21 at 11:26 AM.
#23
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
automotive pulley spanner examples....
clutch pulley spanner/adjustable
flywheel spanner in action
you can/should be able to rent any one of these at an auto store...ie. free!!
ps. sorry for the large image files. got tedious to try and reduce the size
clutch pulley spanner/adjustable
flywheel spanner in action
you can/should be able to rent any one of these at an auto store...ie. free!!
ps. sorry for the large image files. got tedious to try and reduce the size
#24
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,834
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Liked 2,811 Times
in
1,535 Posts
+1 on freeze off and fastest way is to do the lace up a rim
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#25
Senior Member
Join Date: Jun 2006
Location: NW Burbs, Chicago
Posts: 12,047
Mentioned: 201 Post(s)
Tagged: 0 Thread(s)
Quoted: 3011 Post(s)
Liked 3,786 Times
in
1,405 Posts
Get a 2x4, cut in half. Cut 4" down so it fits between the flanges. Clamp pieces together, drill hole slightly larger than barrel diameter down the "seam". Screw wood together around barrel. Nail through spoke holes. Clamp wood in vice.
And Bob's yer uncle.
And Bob's yer uncle.