Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

My nipples keep cracking

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

My nipples keep cracking

Old 01-17-21, 07:37 PM
  #1  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
My nipples keep cracking

I've got an Ibis aluminum mtn bike wheel-set. It has asymmetric rims, and apparently it was built with aluminum nipples (not my choice). On the side of the front wheel that would require slightly longer spokes, I have now had two nipples fail. Oddly, it happens in the garage. My rear wheel is fine, as far as I can tell. The wheel-set has not been heavily used.

Should I have the wheel re-built with brass nipples, or brass nipples and new spokes, or cut my losses and get a new wheel?
Cyclist0108 is offline  
Old 01-17-21, 08:19 PM
  #2  
Shimagnolo
Senior Member
 
Shimagnolo's Avatar
 
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,086
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3355 Post(s)
Liked 5,432 Times in 2,811 Posts
Properly sized spokes put the head of the nipple in compression.
If spokes are too short, they can put the body of the nipple in tension, causing breakage.
Are the spokes long enough to reach the screw slot in the nipple?

See the first image on this page: https://www.wheelfanatyk.com/blog/rim-washers/

Last edited by Shimagnolo; 01-17-21 at 08:40 PM.
Shimagnolo is online now  
Likes For Shimagnolo:
Old 01-17-21, 08:25 PM
  #3  
TiHabanero
Senior Member
 
Join Date: Nov 2012
Posts: 4,435
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1726 Post(s)
Liked 1,350 Times in 705 Posts
Replace with brass nipples and forget about it.
TiHabanero is offline  
Likes For TiHabanero:
Old 01-17-21, 08:31 PM
  #4  
shelbyfv
Expired Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 11,455
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3637 Post(s)
Liked 5,314 Times in 2,700 Posts
Yep, easy to do it yourself, one at a time.
shelbyfv is offline  
Old 01-17-21, 09:30 PM
  #5  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
Originally Posted by shelbyfv
Yep, easy to do it yourself, one at a time.
Nothing like tubeless to turn this into an ordeal of biblical proportions (so much so I would rather do it all at once and get it over with).
Cyclist0108 is offline  
Old 01-17-21, 09:31 PM
  #6  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
Originally Posted by Shimagnolo
Properly sized spokes put the head of the nipple in compression.
If spokes are too short, they can put the body of the nipple in tension, causing breakage.
Are the spokes long enough
No. I am nearly certain this is the cause. The question is what to do about it. (If brass is sufficiently more robust, perhaps just replacing the nipples will do it.)
Cyclist0108 is offline  
Old 01-17-21, 09:34 PM
  #7  
Shimagnolo
Senior Member
 
Shimagnolo's Avatar
 
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,086
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3355 Post(s)
Liked 5,432 Times in 2,811 Posts
Originally Posted by wgscott
No. I am nearly certain this is the cause. The question is what to do about it. (If brass is sufficiently more robust, perhaps just replacing the nipples will do it.)
If the spokes are too short, then you need to replace them with ones that are long enough.
Neither aluminum nor brass nipples can handle spoke tension if the spoke doesn't extend up into the head of the nipple.
Shimagnolo is online now  
Old 01-17-21, 09:38 PM
  #8  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
That's what I was afraid of.
Cyclist0108 is offline  
Old 01-18-21, 12:28 AM
  #9  
MudPie
Senior Member
 
MudPie's Avatar
 
Join Date: May 2004
Location: Southern California
Posts: 2,190
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 114 Post(s)
Liked 118 Times in 91 Posts
Originally Posted by Shimagnolo
Properly sized spokes put the head of the nipple in compression.
If spokes are too short, they can put the body of the nipple in tension, causing breakage.
Are the spokes long enough to reach the screw slot in the nipple?

See the first image on this page: https://www.wheelfanatyk.com/blog/rim-washers/
I didn't realize this. Thanks!
MudPie is offline  
Old 01-18-21, 12:56 AM
  #10  
cpach
Senior Member
 
Join Date: Oct 2009
Location: Mt Shasta, CA, USA
Posts: 2,140

Bikes: Too many. Giant Trance X 29, Surly Midnight Special get the most time.

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 530 Post(s)
Liked 311 Times in 235 Posts
If the spokes are legitimately too short and are putting the nipples in tension this should be considered a warranty issue. Ibis is in town for you, maybe they'd be down with you dropping it off to be rebuilt.
cpach is offline  
Likes For cpach:
Old 01-18-21, 07:40 AM
  #11  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,764
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,871 Times in 4,636 Posts
With this thread title, I was really hoping for a laugh or two with my morning coffee. You people are slipping.
Koyote is offline  
Likes For Koyote:
Old 01-18-21, 07:46 AM
  #12  
dedhed
SE Wis
 
dedhed's Avatar
 
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,516

Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970

Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2731 Post(s)
Liked 3,359 Times in 2,034 Posts
Originally Posted by Koyote
With this thread title, I was really hoping for a laugh or two with my morning coffee. You people are slipping.
Right! I was ready to suggest Bag Balm.
dedhed is offline  
Old 01-18-21, 10:53 AM
  #13  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
Originally Posted by Koyote
With this thread title, I was really hoping for a laugh or two with my morning coffee. You people are slipping.
I tried.
Cyclist0108 is offline  
Old 01-18-21, 11:18 AM
  #14  
79pmooney
Senior Member
 
79pmooney's Avatar
 
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,825

Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder

Mentioned: 128 Post(s)
Tagged: 0 Thread(s)
Quoted: 4742 Post(s)
Liked 3,860 Times in 2,509 Posts
Originally Posted by dedhed
Right! I was ready to suggest Bag Balm.
Never tried it but I bet you could use Bag Balm on the threads to good effect. Also the rim ferrules. Wouldn't stop the cracking but would probably work very well for the build.
79pmooney is offline  
Old 01-18-21, 11:27 AM
  #15  
Shimagnolo
Senior Member
 
Shimagnolo's Avatar
 
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,086
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3355 Post(s)
Liked 5,432 Times in 2,811 Posts
Originally Posted by 79pmooney
Never tried it but I bet you could use Bag Balm on the threads to good effect. Also the rim ferrules. Wouldn't stop the cracking but would probably work very well for the build.
For Koyote:
Shimagnolo is online now  
Old 01-18-21, 11:36 AM
  #16  
rydabent
Banned
 
Join Date: Apr 2010
Location: Lincoln Ne
Posts: 9,924

Bikes: RANS Stratus TerraTrike Tour II

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 3352 Post(s)
Liked 1,054 Times in 634 Posts
Well--------------------------that thread title cause coffee to run out of my nose, and splatter on my keyboard.
rydabent is offline  
Old 01-18-21, 01:20 PM
  #17  
davidad
Senior Member
 
Join Date: Feb 2009
Posts: 6,660
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 582 Post(s)
Liked 171 Times in 138 Posts
Replace the aluminum with brass. Even if they don't quite reach the head they will hold up. Anecdotally the first wheel I built had a few of the threads of the spokes showing. The wheel was laced to a 28 hole SA hub on a refinery beach cruiser. When I retired I gave it to Grumpy who used it until Muscle Head backed a pick truck over it. It lasted 10 years in that environment.
davidad is offline  
Likes For davidad:
Old 01-18-21, 05:50 PM
  #18  
Mad Honk 
Senior Member
 
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,936

Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso

Mentioned: 114 Post(s)
Tagged: 0 Thread(s)
Quoted: 1283 Post(s)
Liked 1,835 Times in 1,109 Posts
If the spoke nipples are a bit too short, find some longer nipples like a 16mm that will give more purchase. I have been buying them from 365 Cycles and they are not expensive. (when used with Bag B they should tighten up nicely!) Smiles, MH
Mad Honk is offline  
Likes For Mad Honk:
Old 01-23-21, 03:11 PM
  #19  
cpach
Senior Member
 
Join Date: Oct 2009
Location: Mt Shasta, CA, USA
Posts: 2,140

Bikes: Too many. Giant Trance X 29, Surly Midnight Special get the most time.

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 530 Post(s)
Liked 311 Times in 235 Posts
Originally Posted by Mad Honk
If the spoke nipples are a bit too short, find some longer nipples like a 16mm that will give more purchase. I have been buying them from 365 Cycles and they are not expensive. (when used with Bag B they should tighten up nicely!) Smiles, MH
This is one of the reasons that longer nipples exist, but I'm unsure of how much stronger they are--I think they mostly just hide some threads. Depending on the brand they may actually have only have as many threads cut as a 12mm, and thread strength isn't a major issue for nipple anyways--a handful of threads hold most of the force regardless. If the spoke is too short there's still going to be putting a portion of the spoke in tension. Ibis wheels, even their aluminum ones, are frickin' expensive and they should be RIGHT.
cpach is offline  
Old 01-23-21, 03:51 PM
  #20  
unterhausen
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,362
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
It would be a pain to go through all the work of nipple replacement and still have failures. Definitely sounds like the spokes are too short.
unterhausen is offline  
Old 01-23-21, 03:59 PM
  #21  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
Sorry I checked out. No power/internet for several days. I can't find the link, but Zinn asserts that spokes too short is nearly always the cause of this. I don't know for sure, but two failures in the comfort of my garage so far this year suggest something is going wrong. I have never even seen this kind of thing before (probably because all my other wheels have brass nipples).

Since Ibis is in town, I might try to get their advice. If they fix it for me, great, but even if not, it would be good to know if it is a known issue. (They have discontinued this particular wheelset).
Cyclist0108 is offline  
Old 01-23-21, 05:29 PM
  #22  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
They seem to be closed to the public for the pandemic.

The rim retails for $99 and the hub (front) is an Ibis-branded no-name. There is nothing wrong with it, but this wheel might not be worth a re-build. It is for my steel off-road drop bar mountain touring bike, so maybe this is an excuse to get a new front wheel with a dynamo hub. What bugs me is I never really got to use this for anything significant.
Cyclist0108 is offline  
Old 01-23-21, 08:54 PM
  #23  
unterhausen
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,362
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
Aluminum is a little weaker depending on the alloy. And I think it might be more susceptible to fatigue failures. But I doubt switching to brass is going to safe this wheel, the short spokes should be replaced.

Originally Posted by wgscott
Nothing like tubeless to turn this into an ordeal of biblical proportions (so much so I would rather do it all at once and get it over with).
In another thread, you previously mentioned that your shop didn't have the right size rim tape. You need to find someone that does. I'm not particularly happy about using tubeless tape, but all my wheels have it now even if I use tubes.
unterhausen is offline  
Likes For unterhausen:
Old 01-24-21, 12:57 AM
  #24  
cpach
Senior Member
 
Join Date: Oct 2009
Location: Mt Shasta, CA, USA
Posts: 2,140

Bikes: Too many. Giant Trance X 29, Surly Midnight Special get the most time.

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 530 Post(s)
Liked 311 Times in 235 Posts
I'd try dropping them by Family Cycling Center or Spokesman. Too bad they won't deal with you directly but those are both pretty nice shops and should sort you out. Should be worth the time. Maybe get a dynamo wheel built in the mean time.
cpach is offline  
Old 01-24-21, 10:41 AM
  #25  
Cyclist0108
Occam's Rotor
Thread Starter
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
Originally Posted by cpach
I'd try dropping them by Family Cycling Center or Spokesman. Too bad they won't deal with you directly but those are both pretty nice shops and should sort you out. Should be worth the time. Maybe get a dynamo wheel built in the mean time.
I bought them at Family, so maybe that might be the way to go. Santa Cruz is taking the isolation pretty seriously (except for the morons on Westcliff giving out free hugs).

Thanks again for all the advice!
Cyclist0108 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.