What have you been wrenching on lately?
#3626
aka Tom Reingold
Thread Starter
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,492
Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem
Mentioned: 511 Post(s)
Tagged: 0 Thread(s)
Quoted: 7341 Post(s)
Liked 2,439 Times
in
1,423 Posts
I overhauled my trailer's other wheel later today. My workbench is too messy. I lost one of the hub dustcaps and absolutely couldn't find it. I found a spare one of those rubber boots some hubs have and put that on instead. Oh well.
I put a cable guide on the Super Course. That was fully of surprises. Drilling a hole in the BB shell was harder than I thought. And it turned out I had to remove the BB cartridge assembly to get the drill bit and tap far enough. And my bolt was too long, so I ground it down on my bench grinder. I love having a bench grinder.
Here is the Super Course with its new Technomic stem, Greallthy bell, and dynamo-powered taillight.
Before the cable guide, I just ran the cable. It worked, but I think it slide side-to-side and changed the adjustment, and that's what led me to use a guide.
After installing the guide:
Here is the stem. I don't like the vertical part of the stem to be longer than the head tube, but oh well, it fits me.
I put a cable guide on the Super Course. That was fully of surprises. Drilling a hole in the BB shell was harder than I thought. And it turned out I had to remove the BB cartridge assembly to get the drill bit and tap far enough. And my bolt was too long, so I ground it down on my bench grinder. I love having a bench grinder.
Here is the Super Course with its new Technomic stem, Greallthy bell, and dynamo-powered taillight.
Before the cable guide, I just ran the cable. It worked, but I think it slide side-to-side and changed the adjustment, and that's what led me to use a guide.
After installing the guide:
Here is the stem. I don't like the vertical part of the stem to be longer than the head tube, but oh well, it fits me.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
#3628
Senior Member
Join Date: Jul 2004
Location: northern michigan
Posts: 13,317
Bikes: '77 Colnago Super, '76 Fuji The Finest, '88 Cannondale Criterium, '86 Trek 760, '87 Miyata 712
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 659 Post(s)
Liked 595 Times
in
313 Posts
Presently doing a restoration on an ‘84 Trek 720 touring. Paint is in very nice condition needing only a basic cleaning, polishing of alloy parts and the usual new stuff. It still has the bar bag with ride badges and patches. What a gem.
Likes For krakhaus:
#3630
Junior Member
This beast.
Full thread here:
https://www.bikeforums.net/classic-v...pro-tours.html
Swedish Centurion Pro Tour with R7000 / GRX Groupset
Full thread here:
https://www.bikeforums.net/classic-v...pro-tours.html
Swedish Centurion Pro Tour with R7000 / GRX Groupset
Likes For herr_hest:
#3631
Overdoing projects
Join Date: Oct 2011
Location: Rotterdam, former republic of the Netherlands
Posts: 2,397
Bikes: Batavus Randonneur GL, Gazelle Orange Excellent, Gazelle Super Licht, Gazelle Grand Tourist, Gazelle Lausanne, Gazelle Tandem, Koga-Miyata SilverAce, Koga-Miyata WorldTraveller
Mentioned: 58 Post(s)
Tagged: 0 Thread(s)
Quoted: 784 Post(s)
Liked 1,237 Times
in
686 Posts
Ironed on a new patch on the Carradice Junior saddlebag, one from the 'Roffa Mon Amour' arthouse open air festival. 'Roffa' being the local slang for Rotterdam and the 'Mon Amour' coming from the Hiroshima Mon Amour arthouse film from the 1959 New Wave cinema movement.
Anyway, enough talk, pics!
Anyway, enough talk, pics!
#3632
Senior Member
Join Date: Jun 2010
Location: Medford MA
Posts: 2,089
Bikes: Ron Cooper touring, 1959 Jack Taylor 650b ladyback touring tandem, Vitus 979, Joe Bell painted Claud Butler Dalesman, Colin Laing curved tube tandem, heavily-Dilberted 1982 Trek 6xx, René Herse tandem
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 964 Post(s)
Liked 1,451 Times
in
723 Posts
A friend of mine has a singlespeed, which became a zero-speed. The pawl spring snapped right half in two, leaving her with no drive. I tested it (bending back and forth with pliers) and it doesn't appear to be brittle due to improper heat-treatment. I wonder why it broke! Also never seen caged bearings in a freewheel. Also never seen the weird remover spline. I ended up knocking it off the wheel with a hammer and punch.
I got her the cheap replacement freewheel from Ebaymazon and she's back on the road, leaving me with this curio. Funny enough, that freewheel has no remover splines! The next guy (realistically probably me) will have to knock off the cover plate and grip the pawl carrier with a pipe wrench to get it off.
I got her the cheap replacement freewheel from Ebaymazon and she's back on the road, leaving me with this curio. Funny enough, that freewheel has no remover splines! The next guy (realistically probably me) will have to knock off the cover plate and grip the pawl carrier with a pipe wrench to get it off.
__________________
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
#3633
Eccentric Old Man
Join Date: Jan 2014
Location: BelleVegas, IL
Posts: 719
Bikes: 1986 Trek 520 Cirrus, 1979 Schwinn Traveler III, Trek T100, 1995 Trek 970, Fuji America
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 248 Post(s)
Likes: 0
Liked 173 Times
in
87 Posts
Sent to a new home this week.
Now to find a home for this.
Now to find a home for this.
#3634
Zip tie Karen
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Two years in the making...
...the tires are glued up and I could test ride it tomorrow. Waiting on black cloth tape, though.
Likes For Phil_gretz:
Likes For bargo68:
#3636
Overdoing projects
Join Date: Oct 2011
Location: Rotterdam, former republic of the Netherlands
Posts: 2,397
Bikes: Batavus Randonneur GL, Gazelle Orange Excellent, Gazelle Super Licht, Gazelle Grand Tourist, Gazelle Lausanne, Gazelle Tandem, Koga-Miyata SilverAce, Koga-Miyata WorldTraveller
Mentioned: 58 Post(s)
Tagged: 0 Thread(s)
Quoted: 784 Post(s)
Liked 1,237 Times
in
686 Posts
Did a small modification on the Sturmey Archer XL-RD5(w) hub in the SilverAce today. (though this should work on the X-RD5(w) as well, though perhaps not on the newer rotary shifting SA RXL-RD5)
These hubs are a further evolution on the classic AW 3-speeds offering 5 speeds while sharing most of the same parts.
It's a known issue on these hubs that the 4th gear can be difficult. 3 > 4 and requires an upshift + downshift to 5 > 4 to go into gear.
I've also had some issues sometimes with a 4 > 3 downshift not going entirely into gear.
Shifting works with 1st gear being the tightest on the cable and 5th being completely limp and the indicator chain pushed into the hub by the clutch spring.
Most of what I've read seems to indicate that the tolerances of the shifter design(s) are to blame.
My theory however was that this is mostly because a) there is insufficient pressure to push it into 4th on an upshift or b) sticky cables. I have mostly ruled out option b and one way I can see option a working is with a stronger clutch spring.
So... I soldered two clutch springs together.
I swapped them today as it is a relatively small operation, only requiring the drive side locknut to be removed, spring swapped and then put back together again.
Initial impressions are good. Shifting feels crisper and no missed shifts anymore in either direction. Cable tension even seems to be less critical compared to what it was before.
I will update in my project thread in the future for long term use.
Two springs soldered together
Original single spring
New double spring. Careful, it tends to jump out when opened.
These hubs are a further evolution on the classic AW 3-speeds offering 5 speeds while sharing most of the same parts.
It's a known issue on these hubs that the 4th gear can be difficult. 3 > 4 and requires an upshift + downshift to 5 > 4 to go into gear.
I've also had some issues sometimes with a 4 > 3 downshift not going entirely into gear.
Shifting works with 1st gear being the tightest on the cable and 5th being completely limp and the indicator chain pushed into the hub by the clutch spring.
Most of what I've read seems to indicate that the tolerances of the shifter design(s) are to blame.
My theory however was that this is mostly because a) there is insufficient pressure to push it into 4th on an upshift or b) sticky cables. I have mostly ruled out option b and one way I can see option a working is with a stronger clutch spring.
So... I soldered two clutch springs together.
I swapped them today as it is a relatively small operation, only requiring the drive side locknut to be removed, spring swapped and then put back together again.
Initial impressions are good. Shifting feels crisper and no missed shifts anymore in either direction. Cable tension even seems to be less critical compared to what it was before.
I will update in my project thread in the future for long term use.
Two springs soldered together
Original single spring
New double spring. Careful, it tends to jump out when opened.
#3637
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,597
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3860 Post(s)
Liked 6,450 Times
in
3,190 Posts
'72 Torpado
Overhauled everything. The Nuovo Record rd required about 2.5 hours alone. Bought two sets of shifters and used the best bits of each. Polished the stem and bars. Found some silver Sugino crank bolts that look way more cool than the plastic dustcaps. The rest is falling into place...
Overhauled everything. The Nuovo Record rd required about 2.5 hours alone. Bought two sets of shifters and used the best bits of each. Polished the stem and bars. Found some silver Sugino crank bolts that look way more cool than the plastic dustcaps. The rest is falling into place...
Likes For SurferRosa:
#3638
Senior Member
Join Date: Dec 2010
Location: St Cloud Fl.
Posts: 1,945
Bikes: Only my riders left...
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 350 Post(s)
Liked 782 Times
in
389 Posts
Fuji Sandblaster SX
Great rider! Lonnnnng...ish. Seems to have been kinda maintained...ish. My new vacation bike!
Last edited by billnuke1; 10-24-20 at 06:47 PM. Reason: Different word...
#3639
Senior Member
Join Date: Mar 2014
Location: City of Angels
Posts: 4,870
Bikes: A few too many
Mentioned: 42 Post(s)
Tagged: 1 Thread(s)
Quoted: 1363 Post(s)
Liked 2,177 Times
in
1,182 Posts
SR,
I like the color very much scheme and the build looks very nice, what did you use to clean all of the aluminum with?
BTW, the garden looks good too!
Best, Ben
I like the color very much scheme and the build looks very nice, what did you use to clean all of the aluminum with?
BTW, the garden looks good too!
Best, Ben
Likes For xiaoman1:
#3640
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,597
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3860 Post(s)
Liked 6,450 Times
in
3,190 Posts
Me too. One of my classier acquisitions.
The usual: my two iron files, 600 grit, and wd-40. I filed quite a bit of rash from the rd. It was mostly just grimey and gross. I ripped paper towels in little squares and used a liberal amount of wd-40. The brakeset, crankset and pedals just needed an overhaul and wipe down. Bars and stem needed wet sanding. Now I just need another shift cable and a screw for one of the Campy top tube clamps.
What did you use to clean all of the aluminum?
#3641
Junior Member
New wheelset, new cassette, new chain, swapped cranks and BB, swapped brakes from Campy (no quick release) to Shimano -- all done for the first time thanks to Park Tool how-to's on YouTube. Getting my work double-checked and derailleurs adjusted today before going for my first decent ride on the thing. So pleased with myself though, never thought I'd end up doing my own work. Now I just need a repair stand so I can do stuff that requires pedaling by hand.
Likes For khyatt:
#3642
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,597
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3860 Post(s)
Liked 6,450 Times
in
3,190 Posts
Seller said he's been the sole owner since he bought it in '72. Apparently, a garage queen. Very little wear except for some small chips in the chainstay. He switched out the Campy crankset and brakeset at some point for Sugino and Dura Ace. Works for me. They both look nos. It had tubulars on Nuovo Tipo hubs. I added the seatpost, clincher wheelset, freewheel, and rd.
#3643
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,029
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4507 Post(s)
Liked 6,373 Times
in
3,665 Posts
Seller said he's been the sole owner since he bought it in '72. Apparently, a garage queen. Very little wear except for some small chips in the chainstay. He switched out the Campy crankset and brakeset at some point for Sugino and Dura Ace. Works for me. They both look nos. It had tubulars on Nuovo Tipo hubs. I added the seatpost, clincher wheelset, freewheel, and rd.
Likes For merziac:
#3644
Veteran, Pacifist
Join Date: Dec 2004
Location: Seattle area
Posts: 13,325
Bikes: Bikes??? Thought this was social media?!?
Mentioned: 284 Post(s)
Tagged: 0 Thread(s)
Quoted: 3896 Post(s)
Liked 4,822 Times
in
2,226 Posts
Here’s the first ‘parts hang’ - just to take some measurements and see what I think - and then rethink things like housing color / saddle / bar tape. Setback? Lacking a good non-aero brake solution. But it is cleaner, shinier, and more rideable for my current needs.
I feel porkchopbmx will be getting an order for several colors of housing.
I feel porkchopbmx will be getting an order for several colors of housing.
Decided to stop looking for the ‘right’ vintage hoods - these are new DiaCompe. The Soma bars are an experiment in narrowness. 34cm ctc at the hoods, 40cm in the drops. I’ll either be narrowly aero or riding the drops a lot. Or in need of a new setup.
__________________
Vintage, modern, e-road. It is a big cycling universe.
Vintage, modern, e-road. It is a big cycling universe.
#3645
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,776
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,394 Times
in
1,928 Posts
Waiting for tires and chain peening tool:
Likes For JohnDThompson:
#3647
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,776
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,394 Times
in
1,928 Posts
Likes For JohnDThompson:
#3648
Senior Member
Join Date: Aug 2017
Location: Germany
Posts: 1,090
Bikes: 80s Alan Super Record, 79' Somec Special, 90s Rossin(?) Columbus Ego Triathlon, previously: Bianchi SBX Reparto Corse (stolen) and so on...
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 391 Post(s)
Liked 812 Times
in
602 Posts
Quikie pic update! Still waiting on cables.
Decided to stop looking for the ‘right’ vintage hoods - these are new DiaCompe. The Soma bars are an experiment in narrowness. 34cm ctc at the hoods, 40cm in the drops. I’ll either be narrowly aero or riding the drops a lot. Or in need of a new setup.
Decided to stop looking for the ‘right’ vintage hoods - these are new DiaCompe. The Soma bars are an experiment in narrowness. 34cm ctc at the hoods, 40cm in the drops. I’ll either be narrowly aero or riding the drops a lot. Or in need of a new setup.
#3649
buy my bikes
Join Date: Jun 2014
Location: Michigan
Posts: 1,799
Bikes: my very own customized GUNNAR CrossHairs
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 519 Post(s)
Liked 426 Times
in
248 Posts
Second shakedown....
Heliomatic hubs from plonz. Built into wheels.
Simplex shifter mounts from francophile
Nitto Albatross bars from Bianchigirll
First ride proved I didn’t tighten the rear wheel enough. Seems ok now-after 12 miles. Hopefully I don’t need shorter drive side spokes.
Simplex shifter mounts from francophile
Nitto Albatross bars from Bianchigirll
First ride proved I didn’t tighten the rear wheel enough. Seems ok now-after 12 miles. Hopefully I don’t need shorter drive side spokes.
Likes For mrv:
#3650
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,597
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3860 Post(s)
Liked 6,450 Times
in
3,190 Posts
.