Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Snapped off bottle cage braze on

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Snapped off bottle cage braze on

Old 01-13-20, 03:36 PM
  #1  
krems81 
Senior Member
Thread Starter
 
Join Date: Apr 2008
Location: Chicago, IL
Posts: 783

Bikes: Schwinn Voyageur

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Liked 6 Times in 6 Posts
Snapped off bottle cage braze on

Any ideas for putting this back on? Braze? I have a basic Home Depot brazing kit. Any chance I can get it back on in a sturdy way without massive paint damage?

Wasnít planning on refinishing this one


__________________
Cog Cycles, Chicago
krems81 is offline  
Old 01-13-20, 03:42 PM
  #2  
thinktubes 
weapons-grade bolognium
 
thinktubes's Avatar
 
Join Date: Dec 2008
Location: Across the street from Chicago
Posts: 5,058

Bikes: Battaglin Cromor, Ciocc Designer 84, Schwinn Superior 1981

Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 568 Post(s)
Liked 338 Times in 192 Posts
JB Weld
thinktubes is online now  
Old 01-13-20, 04:05 PM
  #3  
jackbombay
Senior Member
 
Join Date: Jun 2019
Location: Eastern Idaho
Posts: 687
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 323 Post(s)
Liked 266 Times in 170 Posts
Originally Posted by thinktubes View Post
JB Weld
That is what I would try, zero paint damage.

I would carefully use a file to remove the rust and even take the corner of the end of the file and giuge up both surfaces as much as I could to give the JB weld as much as possible to grab onto.
jackbombay is offline  
Likes For jackbombay:
Old 01-13-20, 04:20 PM
  #4  
non-fixie 
Shifting is fun!
 
non-fixie's Avatar
 
Join Date: Aug 2009
Location: South Holland, NL
Posts: 8,642

Bikes: Yes, please.

Mentioned: 218 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 578 Times in 336 Posts
I'm not familiar with JB Weld, but if it is some sort of super glue, then yes, that's what I would do. And like jackbombay says, prepare the surfaces meticulously.
__________________
The problem with an affliction for 60's bikes: born too late!



non-fixie is online now  
Likes For non-fixie:
Old 01-13-20, 04:41 PM
  #5  
krems81 
Senior Member
Thread Starter
 
Join Date: Apr 2008
Location: Chicago, IL
Posts: 783

Bikes: Schwinn Voyageur

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Liked 6 Times in 6 Posts
Originally Posted by jackbombay View Post
That is what I would try, zero paint damage.

I would carefully use a file to remove the rust and even take the corner of the end of the file and giuge up both surfaces as much as I could to give the JB weld as much as possible to grab onto.
Sounds promising. Would you trust it? Iím not too familiar with the product and this would be a build for someone else to use as a reliable commuter
__________________
Cog Cycles, Chicago
krems81 is offline  
Old 01-13-20, 04:48 PM
  #6  
non-fixie 
Shifting is fun!
 
non-fixie's Avatar
 
Join Date: Aug 2009
Location: South Holland, NL
Posts: 8,642

Bikes: Yes, please.

Mentioned: 218 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 578 Times in 336 Posts
Originally Posted by krems81 View Post
Would you trust it?
For re-attaching a seat stay to the seat lug, probably not. But for a bottle cage, sure.
__________________
The problem with an affliction for 60's bikes: born too late!



non-fixie is online now  
Likes For non-fixie:
Old 01-13-20, 04:53 PM
  #7  
jackbombay
Senior Member
 
Join Date: Jun 2019
Location: Eastern Idaho
Posts: 687
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 323 Post(s)
Liked 266 Times in 170 Posts
Originally Posted by krems81 View Post
Sounds promising. Would you trust it? Iím not too familiar with the product and this would be a build for someone else to use as a reliable commuter
Hmmm, I would certainly use it on my own bike, on someone else's the stakes are a bit higher, but its quite tough, JB weld website claims a tensile strength of 3960 pounds per square inch of adhesion surface.
jackbombay is offline  
Likes For jackbombay:
Old 01-13-20, 04:59 PM
  #8  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 21,300

Bikes: Several, mostly not name brands.

Mentioned: 125 Post(s)
Tagged: 0 Thread(s)
Quoted: 2078 Post(s)
Liked 429 Times in 304 Posts
Not with a fuel/air torch; it would take too long to get up to temperature and cause extensive paint damage. To do it properly, you'll want fuel/oxygen and a high silver content rod. But before that, I'd try JB Weld or something similar, as suggested above. If it fails, you're no worse off than you are now, and can always use a clamp to hold the cage in place.
JohnDThompson is offline  
Old 01-13-20, 05:10 PM
  #9  
bark_eater 
Senior Member
 
Join Date: Sep 2017
Location: Eastern Shore, MD
Posts: 807

Bikes: Road ready: 1993 Koga Miyata City Liner Touring Hybrid, 1989 Centurion Sport DLX, "I Blame GP" Bridgestone CB-1. Projects: Yea, I got a problem....

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 279 Post(s)
Liked 72 Times in 49 Posts
Theres a black locktite thats used for gunsmithing as a basically a silver solder replacement. I think you need a very clean surface for that kind of non gap filling glues.
bark_eater is online now  
Old 01-13-20, 05:27 PM
  #10  
repechage
Senior Member
 
Join Date: Jun 2006
Posts: 14,328
Mentioned: 91 Post(s)
Tagged: 0 Thread(s)
Quoted: 1315 Post(s)
Liked 284 Times in 230 Posts
Wild, maybe a touch of silver at one point of the diamond, maybe, otherwise when flux becomes a structural bonding agent.
mask off well and often, abrade surface, the boss side will be the trick. Picklex 20? (too expensive)

thread a long bolt into the boss as a handle , run a nut to secure, and go at it with a wire wheel on a dremel?
repechage is offline  
Old 01-13-20, 05:37 PM
  #11  
Spaghetti Legs 
Senior Member
 
Join Date: Dec 2014
Location: Central Virginia
Posts: 3,708

Bikes: Numerous

Mentioned: 83 Post(s)
Tagged: 0 Thread(s)
Quoted: 1032 Post(s)
Likes: 0
Liked 296 Times in 155 Posts
You can look into a rivnut. Thatís how the bosses are secured on my aluminum TT bike.

Edit - rather than bosses, I should say it provides a threaded insert for the bottle cage bolt to secure directly into.

https://en.wikipedia.org/wiki/Rivet_nut
__________________
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '85 Moser, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, Ď89 Cinelli Supercorsa, Ď83 Bianchi Specialissima, Ď85 Pinarello Record
Spaghetti Legs is offline  
Old 01-13-20, 05:41 PM
  #12  
brian3069 
Senior Member
 
brian3069's Avatar
 
Join Date: Jun 2009
Posts: 1,675

Bikes: Raleigh Supercourse

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 144 Post(s)
Liked 59 Times in 33 Posts
Maybe it can be reattached with a rivnut.
brian3069 is offline  
Old 01-13-20, 06:21 PM
  #13  
Mad Honk 
Senior Member
 
Join Date: May 2019
Location: Bloomington, IN
Posts: 866

Bikes: Trek 770, Trek 760, Schwinn Peloton, Patelli Professional, Othon Ochsner

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 361 Post(s)
Liked 239 Times in 185 Posts
The clown-eye or diamond boss looks like it didn't have any brass under it. You could try cleaning the parts with a Dremmel tool and epoxying the part back in, but even with 2800 psi epoxy it would be weak. If you have a new clown-eye you could use a riv-nut, or even drill the old boss out of the clown-eye and then riv-nut it in. Some epoxy or JB weld under the eye and then touch it up with some enamel paint. All are work arounds, and not as good a re-brazing. But should hold under normal conditions. HTH, MH
Mad Honk is offline  
Old 01-13-20, 06:29 PM
  #14  
SurferRosa
Senior Member
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Posts: 2,086

Bikes: old school 531c & campy

Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 895 Post(s)
Liked 581 Times in 351 Posts
Using a rivnut would ruin some aesthetic. Does the bike warrant aesthetic?

Is it the top or bottom fitting? If bottom, a simple fix, like jb-weld, will probably last longer there.

As non-fixie said, prepare the surfaces meticulously for the epoxy. Use tape on the paint. Follow the jb-weld instructions. Just buy the regular stuff. No need to go overboard.
SurferRosa is online now  
Old 01-13-20, 09:05 PM
  #15  
obrentharris 
Senior Member
 
obrentharris's Avatar
 
Join Date: May 2012
Location: San Francisco Bay Area
Posts: 2,856

Bikes: fewer (n-1)

Mentioned: 56 Post(s)
Tagged: 0 Thread(s)
Quoted: 746 Post(s)
Likes: 0
Liked 392 Times in 189 Posts
It looks like it was held on for all these years by nothing more than the paint. The JB Weld will be much stronger.
Brent
obrentharris is offline  
Likes For obrentharris:
Old 01-13-20, 10:30 PM
  #16  
thumpism 
Bikes are okay, I guess.
 
thumpism's Avatar
 
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 5,677

Bikes: Waterford Paramount Touring, Trek 510 city build, Giant CFM-2, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1600 Post(s)
Liked 341 Times in 245 Posts
I'd use JB Weld and make sure I squished a little down into the tube to sort of "wrap" the binding stuff over the edge of the hole in the tube, like they do in "plaster and lath" walls. Oil the threads on the screw so it does not get stuck.

thumpism is offline  
Likes For thumpism:
Old 01-13-20, 10:41 PM
  #17  
repechage
Senior Member
 
Join Date: Jun 2006
Posts: 14,328
Mentioned: 91 Post(s)
Tagged: 0 Thread(s)
Quoted: 1315 Post(s)
Liked 284 Times in 230 Posts
Rethinking- Rivnut and a reuse or new diamond "stiffener"
Bringhneli, nova, ceeway, possible sources. JB weld and Rivnut it together in one swoop.

I wonder if there is any braze holding the stiffener to the threaded insert.
repechage is offline  
Old 01-14-20, 12:44 AM
  #18  
Manny66 
Senior Member
 
Manny66's Avatar
 
Join Date: Oct 2018
Location: Whittier
Posts: 359

Bikes: 1970's Windsor Profesional, Pinarello Gavia TSX,Guerciotti SL,Basso Gap, Vintage Moser SL,Concorde TSX,Concorde TVT, Mondia Super,Vitus 979.Diamant SLX,60's Meteor

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 100 Post(s)
Liked 86 Times in 58 Posts
clean it til you get bare metal, JB Weld and your done.
Manny66 is offline  
Likes For Manny66:
Old 01-14-20, 08:17 AM
  #19  
Hudson308 
Mr. Anachronism
 
Hudson308's Avatar
 
Join Date: Jan 2013
Location: City of Lakes
Posts: 1,925

Bikes: fillet-brazed Chicago Schwinns, and some other stuff

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 472 Post(s)
Liked 147 Times in 100 Posts
Originally Posted by Manny66 View Post
clean it til you get bare metal, JB Weld and your done.
Yep
__________________
"If we don't change direction soon, we'll end up where we're going." -Irwin Corey
Hudson308 is offline  
Likes For Hudson308:
Old 01-14-20, 09:06 AM
  #20  
fishboy316 
Senior Member
 
fishboy316's Avatar
 
Join Date: Jan 2015
Location: Arnold Maryland
Posts: 316

Bikes: Cervelo S5, Cannondale AL1 Lefty MTB, Trek X01, Trek Farley 7,1951 Raleigh Sport, 57&60 Raleigh Tourist, 70 Raleigh Super Course, 80's Soma Prestiege,72 Raleigh Grand Sports, 85 Club Fuji, 76 Raleigh Competition, 85 Panasonic,70's Peugot u08. & more

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 36 Post(s)
Likes: 0
Liked 12 Times in 10 Posts
Clean it and use JB. As stated before if it does not hold you are no worse off than now. Jb is tough stuff!
fishboy316 is offline  
Old 01-14-20, 11:49 AM
  #21  
Russ Roth
Senior Member
 
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 751

Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 274 Post(s)
Liked 171 Times in 138 Posts
Clean meticulous and install a river nut then grind down the backside of the diamond and drill it out the center so it can slip over the rivnut. Little light epoxy to hold it in place. It'll be purely decorative at that point. Paint the edges to keep it clean.
Russ Roth is offline  
Old 01-14-20, 08:16 PM
  #22  
madpogue 
Senior Member
 
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 4,342
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1309 Post(s)
Liked 455 Times in 347 Posts
If it's one of two sets of bosses, you could at least use this set just for a pump, and use the other for a water bottle. I would be.... cautious about the weight of a full water bottle attached to this boss JB Welded to the tube.

Schwinn MTB?
madpogue is offline  
Old 01-15-20, 12:21 PM
  #23  
krems81 
Senior Member
Thread Starter
 
Join Date: Apr 2008
Location: Chicago, IL
Posts: 783

Bikes: Schwinn Voyageur

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Liked 6 Times in 6 Posts
Thanks for all the suggestions everyone. It was the bottom boss so I tried JB Weld. Itís been curing since yesterday so Iíll have a look today. Hopefully all good. Iíll update once I check it out
__________________
Cog Cycles, Chicago
krems81 is offline  
Likes For krems81:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.