attaching a head badge
#1
buy my bikes
Thread Starter
Join Date: Jun 2014
Location: Michigan
Posts: 1,801
Bikes: my very own customized GUNNAR CrossHairs
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 519 Post(s)
Liked 428 Times
in
249 Posts
attaching a head badge
Are head badges ever soldered or brazed on?
In the clip below Eric Marth uses an industrial 2 faced tape to attach a brass or bronze BStone head badge. Maybe 3/4 of the way through.
that got me wondering can a simple low temp solder be used for attaching cosmetic bits. Like a copper or brass head badge.
i have some reluctance to drill and thread holes in the head tube. I know it’s done. But I’ve got visions of cracks propagating from the drilled holes.
https://youtu.be/gJPnbpzjbKg
thanks.
In the clip below Eric Marth uses an industrial 2 faced tape to attach a brass or bronze BStone head badge. Maybe 3/4 of the way through.
that got me wondering can a simple low temp solder be used for attaching cosmetic bits. Like a copper or brass head badge.
i have some reluctance to drill and thread holes in the head tube. I know it’s done. But I’ve got visions of cracks propagating from the drilled holes.
https://youtu.be/gJPnbpzjbKg
thanks.
#2
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,518
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 482 Post(s)
Liked 1,593 Times
in
739 Posts
I'd rather use a 2-part epoxy than solder.
I don't think you should worry about a head tube cracking from little holes.
I don't think you should worry about a head tube cracking from little holes.
Likes For BTinNYC:
#3
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,187
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,308 Times
in
1,118 Posts
I too wouldn't worry about correctly drilled holes. Especially no larger than they need to be for a head badge fastener. And the right double sided adhesive tape is stronger than you think when properly applied.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
Likes For Chuck M:
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,095
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4210 Post(s)
Liked 3,875 Times
in
2,315 Posts
Agreed that the tiny holes in the mid section of a head tube shouldn't be a stress riser to any amount. "Drive Screws" are what many use to attach various name plates and such in industry.
Many small scale builders do braze on their badges. I use 56% silver for the stainless steel, water jetted, ones I have. However quality double sided tape will do a good job if the badge has a smooth backside and won't risk discoloring any enameling or paint. Andy
Many small scale builders do braze on their badges. I use 56% silver for the stainless steel, water jetted, ones I have. However quality double sided tape will do a good job if the badge has a smooth backside and won't risk discoloring any enameling or paint. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
Likes For dsaul: