Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Preserving Patina?

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Preserving Patina?

Old 04-12-21, 06:36 PM
  #1  
ddeand 
Senior Member
Thread Starter
 
ddeand's Avatar
 
Join Date: Jul 2004
Location: Twin Cities
Posts: 928
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 206 Post(s)
Liked 102 Times in 46 Posts
Preserving Patina? (Pics Added)

Quick question. What are some methods or recommendations for protecting a 50 year-old frame that has a bit of surface rust and other typical wear and tear? Best way to clean up as much rust as possible? What is best for final coating of the frame? Thanks!




__________________
Some days, it's not even worth gnawing through the restraints.

Last edited by ddeand; 04-13-21 at 09:26 AM.
ddeand is offline  
Old 04-12-21, 08:12 PM
  #2  
merziac
Senior Member
 
merziac's Avatar
 
Join Date: Oct 2015
Location: PDX
Posts: 14,099

Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2

Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4493 Post(s)
Liked 6,297 Times in 3,632 Posts
merziac is offline  
Old 04-12-21, 10:47 PM
  #3  
Insidious C. 
Senior Member
 
Join Date: Jan 2014
Location: PNW
Posts: 1,598

Bikes: One of everything and three of everything French

Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 457 Post(s)
Liked 329 Times in 207 Posts
I think we're going to need to see some pics.
__________________
I.C.
Insidious C. is offline  
Old 04-12-21, 11:30 PM
  #4  
frogman
Senior Member
 
frogman's Avatar
 
Join Date: Sep 2006
Location: Napa Valley, CA
Posts: 908

Bikes: Wife says I have too many :-)

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 327 Post(s)
Liked 248 Times in 158 Posts
Here's what I would do if the rust isn't too extensive.
Clean and dry the frame, lightly sand the rust areas with steel wool then spray them with Krylon Rust Stop then spray the entire frame with Krylon clear coat.
frogman is offline  
Likes For frogman:
Old 04-13-21, 12:40 AM
  #5  
gaucho777 
Senior Member
 
gaucho777's Avatar
 
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,445

Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin

Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 826 Post(s)
Liked 2,048 Times in 545 Posts
Pics might be helpful, but this is my general advice:

1. Strip frame
2. Clean and degrease frame/fork
3. Soak frame/fork in oxalic acid bath (approx. 24-36 hours with a dilution of about 1 tablespoon per gallon of water)
4. Apply wax (I avoid cleaning/polishing wax unless paint has dulled)
5. Rebuild with new grease/bearings/cables as needed


Last edited by gaucho777; 04-13-21 at 12:45 AM.
gaucho777 is offline  
Likes For gaucho777:
Old 04-13-21, 04:59 AM
  #6  
nlerner
Senior Member
 
Join Date: Dec 2005
Posts: 17,127
Mentioned: 480 Post(s)
Tagged: 0 Thread(s)
Quoted: 3788 Post(s)
Liked 6,573 Times in 2,580 Posts
Originally Posted by merziac
Rub with popcorn?
nlerner is offline  
Likes For nlerner:
Old 04-13-21, 05:36 AM
  #7  
jonwvara 
Senior Member
 
jonwvara's Avatar
 
Join Date: Apr 2006
Location: Washington County, Vermont, USA
Posts: 3,787

Bikes: 1966 Dawes Double Blue, 1976 Raleigh Gran Sport, 1975 Raleigh Sprite 27, 1980 Univega Viva Sport, 1971 Gitane Tour de France, 1984 Lotus Classique, 1976 Motobecane Grand Record

Mentioned: 77 Post(s)
Tagged: 0 Thread(s)
Quoted: 758 Post(s)
Liked 647 Times in 343 Posts
Originally Posted by nlerner
Rub with popcorn?
It's like media blasting, but easier on the paint. Extra butter is a good idea.
__________________
www.redclovercomponents.com

"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
jonwvara is offline  
Likes For jonwvara:
Old 04-13-21, 06:27 AM
  #8  
mechanicmatt
Hoards Thumbshifters
 
mechanicmatt's Avatar
 
Join Date: Jul 2010
Location: Signal Mountain, TN
Posts: 1,173

Bikes: '23 Black Mtn MC, '87 Bruce Gordon Chinook, '08 Jamis Aurora, '86 Trek 560, '97 Mongoose Rockadile, & '91 Trek 750

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 245 Post(s)
Liked 322 Times in 189 Posts
Originally Posted by gaucho777
Pics might be helpful, but this is my general advice:

1. Strip frame
2. Clean and degrease frame/fork
3. Soak frame/fork in oxalic acid bath (approx. 24-36 hours with a dilution of about 1 tablespoon per gallon of water)
4. Apply wax (I avoid cleaning/polishing wax unless paint has dulled)
5. Rebuild with new grease/bearings/cables as needed

What wax do you recommend?
mechanicmatt is offline  
Old 04-13-21, 07:14 AM
  #9  
nlerner
Senior Member
 
Join Date: Dec 2005
Posts: 17,127
Mentioned: 480 Post(s)
Tagged: 0 Thread(s)
Quoted: 3788 Post(s)
Liked 6,573 Times in 2,580 Posts
Originally Posted by jonwvara
It's like media blasting, but easier on the paint. Extra butter is a good idea.
I did read on the Internet that Orville Redenbacher got his start in frame refinishing.
nlerner is offline  
Old 04-13-21, 07:42 AM
  #10  
BFisher
Senior Member
 
Join Date: Aug 2013
Posts: 2,336
Mentioned: 35 Post(s)
Tagged: 0 Thread(s)
Quoted: 767 Post(s)
Liked 1,897 Times in 889 Posts
Originally Posted by nlerner
I did read on the Internet that Orville Redenbacher got his start in frame refinishing.
He did the Wright Bros. frames, didn't he?
BFisher is offline  
Likes For BFisher:
Old 04-13-21, 07:51 AM
  #11  
Wildwood 
Veteran, Pacifist
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,303

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 284 Post(s)
Tagged: 0 Thread(s)
Quoted: 3875 Post(s)
Liked 4,779 Times in 2,204 Posts
oxalic acid bath may not be needed at all. For surface rust only - it can be neutralized without soaking the entire frame. When you pull the BB check for internal rust, if none is present, I would not OA bath the entire frame.

But all answers are general responses without seeing the frame detail pics.

Last edited by Wildwood; 04-14-21 at 10:51 AM.
Wildwood is offline  
Old 04-13-21, 11:00 AM
  #12  
ddeand 
Senior Member
Thread Starter
 
ddeand's Avatar
 
Join Date: Jul 2004
Location: Twin Cities
Posts: 928
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 206 Post(s)
Liked 102 Times in 46 Posts
Thanks for the suggestions - I appreciate them. I probably won't be using the Reddenbacher method since I swore off popcorn a couple years ago, and I know that I'd end up eating the stuff before I got it on the frame. I also don't want to do the whole "dip the frame" method unless I really have to. My other vintage projects have all entailed stripping the frame and doing a complete respray, but this is going to be a utility bike (not a restoration) that will eventually become my pavement/gravel "fishing bike". (More on that when I get it done.) Any more ideas are welcome!
__________________
Some days, it's not even worth gnawing through the restraints.
ddeand is offline  
Old 04-13-21, 12:02 PM
  #13  
merziac
Senior Member
 
merziac's Avatar
 
Join Date: Oct 2015
Location: PDX
Posts: 14,099

Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2

Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4493 Post(s)
Liked 6,297 Times in 3,632 Posts
Originally Posted by nlerner
Rub with popcorn?
You might be on to something.
merziac is offline  
Old 04-13-21, 03:16 PM
  #14  
Wileyone1
Banned
 
Join Date: Apr 2021
Posts: 10
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Liked 3 Times in 2 Posts
Originally Posted by mechanicmatt
What wax do you recommend?
Any quality car wax will work.
Wileyone1 is offline  
Old 04-13-21, 03:40 PM
  #15  
genejockey 
Klaatu..Verata..Necktie?
 
genejockey's Avatar
 
Join Date: May 2007
Location: SF Bay Area
Posts: 17,651

Bikes: Litespeed Ultimate, Ultegra; Canyon Endurace, 105; Battaglin MAX, Chorus; Bianchi 928 Veloce; Ritchey Road Logic, Dura Ace; Cannondale R500 RX100; Schwinn Circuit, Sante; Lotus Supreme, Dura Ace

Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 10243 Post(s)
Liked 11,596 Times in 5,943 Posts
I've seen the guy on the "BikeIt UK" YouTube channel use a product called Kurust for neutralizing/converting rust before doing touch up painting over it. AFAICT, it's not sold in the US, so at the moment I'm waiting for it to arrive from Merry Olde. I'll post results when/if I see it. Apart from that, I had pretty good results with Meguiar's Scratch-X on a 1989 Schwinn Circuit that had dulled, but not faded paint and no rust to speak of.
__________________
"Don't take life so serious-it ain't nohow permanent."

"Everybody's gotta be somewhere." - Eccles
genejockey is offline  
Old 04-13-21, 04:44 PM
  #16  
27inch
vintage rider
 
Join Date: Jan 2018
Posts: 96

Bikes: 1937 Roadmaster, 1972 Schwinn Typhoon, 1972 Raleigh Sports

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Liked 11 Times in 8 Posts
Any bike that old likely needs to come completely apart for a thorough cleaning and relube at the very least.
I like the idea of just polishing off the rust a bit and giving it a coat of clear gloss. It'll preserve the decals and original paint. I'm not sure if Krylon is the best or not, some rattle can clear paints will yellow with age. I've used clear lacquer in the past but not from a rattle can, as well as Dupont auto finish from the paint shop, which I normally have around the garage anyhow.
I wouldn't worry about soaking the whole frame unless you open things up and find its a rusty mess inside. chances are you just have a few rusty scratches that need to be addressed.
You could spot clean the rusty spots with some Evaporust, then polish the original paint up as best you can with some light polish but saving the decals is tough when trying to get gloss back out of old paint like that, especially if its pinstriped. The clean and clear method may be your best option to preserve the decals and any pinstripes.
27inch is offline  
Old 04-13-21, 05:09 PM
  #17  
C9H13N 
Full Member
 
Join Date: Dec 2012
Location: North Seattle
Posts: 391

Bikes: Davidson ’81

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 120 Post(s)
Liked 229 Times in 121 Posts
My 2 cents - don’t do anything permanent unless you’re going to spring for a full repaint/powder job. IMO most paint touch ups look like crap and are worse than leaving as is.

Strip it down to the bare frame and fork, wash, lightly polish (previously mentioned Scratch-X works well). Give it a couple coats of automotive paste wax. Reapply wax occasionally to maintain. It’s lasted this long with less care than that.
C9H13N is offline  
Likes For C9H13N:
Old 04-13-21, 06:15 PM
  #18  
jonwvara 
Senior Member
 
jonwvara's Avatar
 
Join Date: Apr 2006
Location: Washington County, Vermont, USA
Posts: 3,787

Bikes: 1966 Dawes Double Blue, 1976 Raleigh Gran Sport, 1975 Raleigh Sprite 27, 1980 Univega Viva Sport, 1971 Gitane Tour de France, 1984 Lotus Classique, 1976 Motobecane Grand Record

Mentioned: 77 Post(s)
Tagged: 0 Thread(s)
Quoted: 758 Post(s)
Liked 647 Times in 343 Posts
Originally Posted by C9H13N
My 2 cents - don’t do anything permanent unless you’re going to spring for a full repaint/powder job. IMO most paint touch ups look like crap and are worse than leaving as is.

Strip it down to the bare frame and fork, wash, lightly polish (previously mentioned Scratch-X works well). Give it a couple coats of automotive paste wax. Reapply wax occasionally to maintain. It’s lasted this long with less care than that.
Agreed. In any case, the existing paint looks good--definitely at the light end of the patina scale, by my standards, at least.
__________________
www.redclovercomponents.com

"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
jonwvara is offline  
Old 04-13-21, 06:23 PM
  #19  
jdawginsc 
Edumacator
 
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,426

Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...

Mentioned: 56 Post(s)
Tagged: 0 Thread(s)
Quoted: 2385 Post(s)
Liked 2,930 Times in 1,861 Posts
Rust is grey hair on a vintage bike. If you dye it, no one seriously believes you have grayless hair...

Clean, polish a bit, and enjoy the small bits of patina!!! Each rust spot has a story to tell!

Do not take my advice by the way...powdered butter flavoring for popcorn is my secret polishing ingredient!
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super












jdawginsc is offline  
Likes For jdawginsc:
Old 04-13-21, 09:29 PM
  #20  
ddeand 
Senior Member
Thread Starter
 
ddeand's Avatar
 
Join Date: Jul 2004
Location: Twin Cities
Posts: 928
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 206 Post(s)
Liked 102 Times in 46 Posts
From the suggestions so far, I think I have a plan of attack. The frame has been stripped - bottom bracket is off, headset will be next. First, the grease, oil, and grime will be scrubbed off with degreaser and Simple Green. Second, I’ll work on the rust spots to the extent that the paint isn’t further damaged. Third, I’ll try a light rubbing compund to smooth out the remaining finish, followed by a polishing compound to really smooth things out. Finally, I’ll apply a few coats of wax. I think that’s about as finished as a “fishing bike” should be.
__________________
Some days, it's not even worth gnawing through the restraints.
ddeand is offline  
Old 04-13-21, 09:49 PM
  #21  
canklecat
Me duelen las nalgas
 
canklecat's Avatar
 
Join Date: Aug 2015
Location: Texas
Posts: 13,522

Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel

Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4559 Post(s)
Liked 2,798 Times in 1,798 Posts
For small rust spots try Brownell's Oxpho-Blue. It's the best cold blue I've tried (the Oxpho-Blue liquid, not the cream or paste based stuff). Mostly for firearms but works on any carbon steel to remove and neutralize light surface rust. I'd usually wind some fine steel wool around cotton swabs, dipped in Oxpho-Blue, and lightly rub the rust spots to remove the excess while simultaneously blackening the bare steel to prevent further rusting.

I wouldn't treat an entire frame with the stuff, but to minimize rust on a bike that I just wanted to knock the dirt off of and protect against further rusting, it should do fine.
canklecat is offline  
Likes For canklecat:
Old 04-14-21, 12:26 AM
  #22  
Brad L 
Senior Member
 
Brad L's Avatar
 
Join Date: Dec 2018
Location: Southeast TX
Posts: 615

Bikes: Several

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 204 Post(s)
Liked 1,014 Times in 315 Posts
I use Metal Prep from POR-15. It has phosphoric acid, which will leave a rust-proof protective layer. Once I've cleaned the area and removed the loose rust, I lightly scrub the area down with a soft paper towel wetted with Metal Prep. It doesn't appear to harm the existing paint but the bare metal turns a dark grey. I have a fender on a car I'm restoring that I stripped to bare metal and treated with Metal Prep about 6 years ago. I did nothing to it afterwards and there's still no rust.
Brad L is offline  
Likes For Brad L:
Old 04-14-21, 10:42 AM
  #23  
75lechamp 
Full Member
 
Join Date: Feb 2014
Location: Arvada, Colorado
Posts: 344

Bikes: 1975 Motobecane LeChampion (silver lilac), 1974 Motobecane Grand Jubile (red/black); 1975 Motobecane Team Champion (orange); 1982 Pinarello Professional (Exorcist Green); 1974 Raleigh Professional MkIV mink blue, 1974 Motobecane Grand Record blk/red

Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 103 Post(s)
Liked 748 Times in 172 Posts
Patina treatment

I recently got a Motobecane that had basically been sitting outside for about 30 years, and considered a repaint. However, I got it from the original owner, and I wanted to instead try to honor that heritage. So, I basically spot treated rust in the bare spots, polished the whole frame and then used a 2K clear coat (the kind that is in the spray can, that has the hardener you can mix in, then need to use in 24 hours I think.). Then wet sanded and polished the clear. I took some artistic liberties with the Champion Team decal I added, by mixing the original black script with gold in the bare metal areas. I like it, but others may not...




75lechamp is offline  
Likes For 75lechamp:
Old 04-14-21, 11:27 AM
  #24  
geeteeiii
Junior Member
 
Join Date: Dec 2020
Location: Estonia
Posts: 139

Bikes: HVZ Meteor 1979, HVZ Champion 1962, HVZ SS Moskva80 1981, Dürkopp 1936

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 39 Post(s)
Liked 345 Times in 69 Posts
Without any serious flaky rust, i dont do anything with frame. I dont ride it in the rain and keep it in a dry place, so its unlikely it will get any worse.
geeteeiii is offline  
Old 04-14-21, 04:10 PM
  #25  
Humanbeing757
Junior Member
 
Join Date: Nov 2020
Location: GB
Posts: 24

Bikes: 1962 Dawes Realmrider 1984 Raleigh Record Ace 2009 Specialized Hardrock 2021 Whyte Sterling 1984 Al Carter Hot Rock 2013 Giant Defy 1

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 27 Times in 12 Posts
I’m also building up a ‘patinated’ bike. I’m planning to apply a coat of boiled linseed oil after I’ve cleaned the frame.
Humanbeing757 is offline  
Likes For Humanbeing757:

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.