View Poll Results: What should I do?
Replace with used 200GS
0
0%
Voters: 11. You may not vote on this poll
What to do with 90's hybrid bike
#1
Newbie
Thread Starter
Join Date: May 2021
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What to do with 90's hybrid bike
Hi all!
I have a 1992 Trek 820 Antelope, which has a rather heavy cr-mo steel frame and a Shimano 200GS groupset. The drivetrain components are slowly but surely failing after nearly thirty years, and the canti brakes aren't holding up too well either, especially compared to modern side-pull brakes. The bike gets used for very short distance rides and light gravel, but nothing more.
I'm willing to spend $150 or less on refurbishing it, not including paint and sandblasting, if it comes down to that. I have already replaced the tires, tubes, and cables.
So, I'd like your opinions! (And I know what a risk it is to ask the Internet for an opinion)
I have a 1992 Trek 820 Antelope, which has a rather heavy cr-mo steel frame and a Shimano 200GS groupset. The drivetrain components are slowly but surely failing after nearly thirty years, and the canti brakes aren't holding up too well either, especially compared to modern side-pull brakes. The bike gets used for very short distance rides and light gravel, but nothing more.
I'm willing to spend $150 or less on refurbishing it, not including paint and sandblasting, if it comes down to that. I have already replaced the tires, tubes, and cables.
So, I'd like your opinions! (And I know what a risk it is to ask the Internet for an opinion)
- Is this bike simply past its prime and not worth salvaging? If it is, should I just bite the bullet and get another bike to replace it or just keep riding it 'til it don't ride no more
- If you think it'd still be cool to restore it back to its former glory, should I:
- Go used-parts hunting: a Shimano 200GS for less used Shimano 200GS
- Replace like-for-like: a Shimano 200GS for a modern-day equivalent, like Shimano Tourney - I'm not leaning towards this option to begin with, and I don't like 3x
- Replace with a tier-up: A Shimano 200GS for a mich-mash of components like V-brakes, a new cassette, and a 1x chainring on the front
- Replace with a complete groupset: A Shimano 200GS for something complete like a Box Three or Box Four groupset, along with V-brakes and a 1x chainring on the front
- Go all out: Tear down the bike (I already have the tools), get it resprayed and laquered, and replace everything with a Box Three or Box Four groupset
#2
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
You left out the most important data point of all - if and how you use the bike now.
It doesn't make any sense to me to spend a lot of money on a bike that you don't like anymore. It also makes no sense to me to ignore or even replace a bike just because you've enjoyed and loved it for a long time.
It doesn't make any sense to me to spend a lot of money on a bike that you don't like anymore. It also makes no sense to me to ignore or even replace a bike just because you've enjoyed and loved it for a long time.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
#3
Newbie
Thread Starter
Join Date: May 2021
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,095
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4210 Post(s)
Liked 3,875 Times
in
2,315 Posts
I see little value in making a bike into what it wasn't intended to be when it involves more cost then the used value of the bike. Unless this bike has some intangible value and is already very close to what one wants, after sinking $ into it, I say move it along to someone else. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,811 Times
in
3,319 Posts
Hybrid bikes started out as a cross between an off-road mountain bike and a road bike. I can only see that as a bike with less than desirable qualities for either genre of cycling.
If you ride off the paved roads and trails, you need something for off road. If you ride paved roads, even paved roads in the mountains, you need a bike for paved roads.
If you wish to combine the two, then maybe a cross bike or gravel bike might fill the need, but I'd still buy a bike for the specific type of riding I'm going to do the most with it.
Though the geometry of Hybrids might at a glance look like you can just put drop bars on them and have a road bike, that isn't so all the time. Tube lengths and stuff is a little different on them.
If you ride off the paved roads and trails, you need something for off road. If you ride paved roads, even paved roads in the mountains, you need a bike for paved roads.
If you wish to combine the two, then maybe a cross bike or gravel bike might fill the need, but I'd still buy a bike for the specific type of riding I'm going to do the most with it.
Though the geometry of Hybrids might at a glance look like you can just put drop bars on them and have a road bike, that isn't so all the time. Tube lengths and stuff is a little different on them.
#7
Senior Member
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times
in
421 Posts
I'd get it into the best possible state of lubrication and adjustment, then leave it and go for N+1. The problem with gradual upgrades is you're stuck with the component standards of that era, and whatever odd parts you can find that will fit. Don't overlook brake pads.
#8
Junior Member
Join Date: Sep 2011
Location: San Juan, PR
Posts: 160
Bikes: 1980's Royce Union "fixed wheel", 1995 Trek 370, 406 -wheeled " shopper/minivelo"for running errands, SS Raleigh M60
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 58 Times
in
46 Posts
Perform a tune up, replace cables and pads, and call it a day; leave the rest as-is for a nice grocery getter or a lender. Splurge on a newer bike with the specs desired; it'll be cheaper in the long run. Good luck!
Likes For Juan el Boricua:
#9
Full Member
I just acquired 2 Trek 820's.
The first I found in a neighbor's trash. It was clapped out and needed new gears, brakes, wheels, bearings and cables. And the seat-post was stuck like Excalibur's sword. But I found another MTB with 3x7 Sram parts and got it going and gave it to a friend as an urban go-getter/gravel bike.
Another friend commented on how good this bike rode so I got another for $40. This one was fine and had original GS200 components and it rides great after a quick tune up and new cables (it already had kool-stop pads).
My verdict? This model is a keeper.
Another friend just bought a $1700 Surley Troll and there's not much between them. Sure, it has disc brakes and a modern 1x drivetrain but they ride similar and the weight is not that much different. I concur with others here who say new cables, good brake pads (like kool-stop) and replace the derailleur with whatever you can find but its worth looking for a 2nd hand Deore or similar quality. This bike is from the golden era of bikes when they still had unbreakable, no-suspension CrMo frames, modern drivetrains which shift and brake well and parts that are still super easy to source and work on.
The first I found in a neighbor's trash. It was clapped out and needed new gears, brakes, wheels, bearings and cables. And the seat-post was stuck like Excalibur's sword. But I found another MTB with 3x7 Sram parts and got it going and gave it to a friend as an urban go-getter/gravel bike.
Another friend commented on how good this bike rode so I got another for $40. This one was fine and had original GS200 components and it rides great after a quick tune up and new cables (it already had kool-stop pads).
My verdict? This model is a keeper.
Another friend just bought a $1700 Surley Troll and there's not much between them. Sure, it has disc brakes and a modern 1x drivetrain but they ride similar and the weight is not that much different. I concur with others here who say new cables, good brake pads (like kool-stop) and replace the derailleur with whatever you can find but its worth looking for a 2nd hand Deore or similar quality. This bike is from the golden era of bikes when they still had unbreakable, no-suspension CrMo frames, modern drivetrains which shift and brake well and parts that are still super easy to source and work on.
#10
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,807
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1944 Post(s)
Liked 2,164 Times
in
1,323 Posts
10 years ago I would have said to go buy good (XT, LX) used 1990’s components and build it back up. Unfortunately the price of older parts has become obscene; and tough to find. I was floored recently when I went looking for some Avid SD7 V-brakes, actually any higher quality V-brakes.
The biggest issue is what are you going to spend on a new bike, and what is your return in use if the new bike is used a few K’s at a time.
I would probably test out a few newer bikes, if you can, to see if you prefer the ride and newer components. Then just decide where you want to put your money.
John
The biggest issue is what are you going to spend on a new bike, and what is your return in use if the new bike is used a few K’s at a time.
I would probably test out a few newer bikes, if you can, to see if you prefer the ride and newer components. Then just decide where you want to put your money.
John
#11
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,663
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1948 Post(s)
Liked 1,472 Times
in
1,020 Posts
#12
Senior Member
Join Date: Jun 2007
Location: Wisconsin
Posts: 6,319
Bikes: 2012 Salsa Casseroll, 2009 Kona Blast
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1031 Post(s)
Liked 208 Times
in
146 Posts
It shouldn't be that hard to keep an old Trek 820 going. Whatever parts you can find, old parts bin, NOS or equivalent new gear like Altus should all work. FWIW, I don't see anything wrong with Cantilever brakes. Just replace the cables if they are frayed or worn, and new pads and you should be good to go.
#13
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
You've already put new tires, tubes and cables on it so those costs have been made. I'd clean up, lube and adjust the bearings, add new brake pads and ride it until something really major need to be replaced.