Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Sizing/Cutting MTB handlebars

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Sizing/Cutting MTB handlebars

Old 06-19-19, 10:15 AM
  #1  
ronin4740
Senior Member
Thread Starter
 
Join Date: Jun 2019
Location: Reno Nevada
Posts: 123

Bikes: Giant TCR, Pure City Original Fixie, Fuji Roubaix, Raleigh M800

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 21 Times in 14 Posts
Sizing/Cutting MTB handlebars

Am mounting a new aluminum MTB handlebar and am considering using a Dremel tool with a cut off wheel to make the cut rather than a hacksaw. Any thoughts on the sanity of doing so?

Thanks!
ronin4740 is offline  
Old 06-19-19, 10:35 AM
  #2  
jimc101
Senior Member
 
Join Date: Oct 2007
Location: West Yorkshire, United Kingdom
Posts: 5,773
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 453 Post(s)
Liked 104 Times in 87 Posts
It will probably give you a messier cut then if you did it with a hacksaw (and guide). Your bars, your choice in how you cut them

And make sure that you don't cut too short, you can always cut more later, but can't add back on.
jimc101 is offline  
Old 06-19-19, 10:43 AM
  #3  
ronin4740
Senior Member
Thread Starter
 
Join Date: Jun 2019
Location: Reno Nevada
Posts: 123

Bikes: Giant TCR, Pure City Original Fixie, Fuji Roubaix, Raleigh M800

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 21 Times in 14 Posts
True that Thanks!
ronin4740 is offline  
Old 06-19-19, 11:23 AM
  #4  
sjh953
Member
 
Join Date: Jan 2009
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Liked 6 Times in 4 Posts
Just use a tube cutter, like the one pictured. I used this one to cut off a few inches on my mtn bike handlebars; totally clean cut, perfectly square, and easy to measure. Much better than hacking it off. Available at any hardware store.
sjh953 is offline  
Likes For sjh953:
Old 06-19-19, 12:20 PM
  #5  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
You can also use a hose clamp for a saw guide.
Make sure you leave enough room for grips, shifter/brake etc.
I had trimmed a bar (about 1" on each end) when I had thumb friction shifters. When I upgraded to ST-EF65's, I was about 3/4" short to fit my Ergon grips.
Bill Kapaun is offline  
Old 06-19-19, 12:30 PM
  #6  
El Gato27
Senior Member
 
Join Date: Dec 2014
Location: Texas
Posts: 230

Bikes: '88 Peugot 12 spd road bike, Nishiki hybrid, JC Penney 10 spd

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 61 Post(s)
Likes: 0
Liked 1 Time in 1 Post
+1 on the tube cutter--cleaner cut vs a hacksaw.
El Gato27 is offline  
Old 06-19-19, 12:50 PM
  #7  
dsbrantjr
Senior Member
 
dsbrantjr's Avatar
 
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319

Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta

Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times in 723 Posts
Tube cutters work well (a little oil on the wheel and cut area will make the job easier) although they will sometimes leave burrs on the inner and outer surfaces, since they push metal aside to make the cut, but that is easily cleaned up with a little file work.
dsbrantjr is offline  
Old 06-19-19, 01:15 PM
  #8  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
I used the bike shop's hacksaw cutting guide and the cut came our square.. which is why the saw guide exists..

It is used mostly for threadless steering tubes , but adjusts for smaller as well..





,...
fietsbob is offline  
Old 06-19-19, 03:04 PM
  #9  
ronin4740
Senior Member
Thread Starter
 
Join Date: Jun 2019
Location: Reno Nevada
Posts: 123

Bikes: Giant TCR, Pure City Original Fixie, Fuji Roubaix, Raleigh M800

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 21 Times in 14 Posts
Thanks again all! The tube cutter looks to be the tool for the job. I'll stop by Harbor Freight and pick one up - yes, I know their tool quality isn't the best but I'm only going to do this once or twice and at $6.00 if it works a couple of times I'll be happy.
ronin4740 is offline  
Old 06-19-19, 06:20 PM
  #10  
2cam16
Senior Member
 
2cam16's Avatar
 
Join Date: Oct 2016
Location: San Mateo,Ca.
Posts: 4,348

Bikes: TRIMMED DOWN THE HERD

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 926 Times in 593 Posts
I always use my pipe cutter.
2cam16 is offline  
Old 06-19-19, 08:46 PM
  #11  
Retro Grouch 
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
Originally Posted by jimc101
And make sure that you don't cut too short, you can always cut more later, but can't add back on.
My thoughts too. I slide the shifters, brake levers, grips and anything else to be mounted onto the handlebars to test fit how much space is available before cutting. If the handlebars have a rise to them, I'm always surprised at how little space is available.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Retro Grouch is offline  
Old 06-19-19, 09:12 PM
  #12  
ronin4740
Senior Member
Thread Starter
 
Join Date: Jun 2019
Location: Reno Nevada
Posts: 123

Bikes: Giant TCR, Pure City Original Fixie, Fuji Roubaix, Raleigh M800

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 21 Times in 14 Posts
Done! Bought the $5 tubing cutter, used some 3 in 1 oil. Nice flat cut . Used the dremmel sanding drum to remove the flair from the ends.

Thanks fur the suggestions!
ronin4740 is offline  
Likes For ronin4740:
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Darth Lefty
Mountain Biking
0
10-24-15 07:11 PM
asmac
Bicycle Mechanics
10
06-23-13 02:39 PM
cpblue
Mountain Biking
4
05-29-11 05:57 AM
johnny b good
Bicycle Mechanics
2
08-17-10 09:15 PM
benajah
Bicycle Mechanics
8
07-07-10 02:38 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.