Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Pedal Bearing Race And Keeper Nut

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Pedal Bearing Race And Keeper Nut

Old 06-02-17, 07:38 AM
  #1  
_ForceD_
Senior Member
Thread Starter
 
_ForceD_'s Avatar
 
Join Date: Jul 2015
Location: Rhode Island
Posts: 1,213

Bikes: Several...from old junk to new all-carbon.

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 502 Post(s)
Liked 78 Times in 49 Posts
Pedal Bearing Race And Keeper Nut

I had to disassemble a clipless pedal to re-lube the bearings. The outer bearings has the race nut, and then a keeper nut (and then a rubber external plug). But the nuts are recessed inside the pedal. I tighten the race so that it's just up to the the ball bearings, and then tighten the keeper nut just finger tight (although with pliers since I can't get my fingers in there). But, that isn't thight enough to keep the assembly from coming off the spindle, and if I tighten it too much it binds the pedal. I need to tighten the keeper against the race (without the race tightening more) but can't get anything in there to hold the race in place while I tighten the keeper nut. Suggestions?

Dan

Last edited by _ForceD_; 06-02-17 at 07:52 AM.
_ForceD_ is offline  
Old 06-02-17, 08:18 AM
  #2  
sweeks
Senior Member
 
sweeks's Avatar
 
Join Date: Sep 2004
Location: Chicago area
Posts: 1,316

Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 565 Post(s)
Liked 60 Times in 46 Posts
You can get an inexpensive set of metric "deep-well" sockets (1/4" drive). In my experience with MKS pedals, the cones are 13mm and the locknuts are 10mm. I can jam these nuts together by turning the 10mm nut clockwise *or* the 13mm race *counter-clockwise*... this is a handy way to adjust the bearings.
Steve
sweeks is online now  
Old 06-02-17, 06:24 PM
  #3  
hueyhoolihan
Senior Member
 
Join Date: Dec 2010
Location: Above ground, Walnut Creek, Ca
Posts: 6,681

Bikes: 8 ss bikes, 1 5-speed touring bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 86 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
just the other day i checked a couple of old quill pedals to see if they were lubricated properly. they had loose ball bearings, a threaded cone, a male tabbed washer that fit into a female groove in the spindle and a locknut. at first i didn't see the tabbed washer and wondered 'how the heck am i supposed to adjust the cones?' before i noticed the old grease encrusted washer in there.

so... is it possible that a washer is missing?

BTW, IIRC i think i had a set of pedals that had a plastic, or rubber, end piece wac actually instrumental in holding the lock nut in place... they may have been an old set of eggbeaters. IDK. maybe i dreamed it.

Last edited by hueyhoolihan; 06-02-17 at 06:28 PM.
hueyhoolihan is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
UniChris
Bicycle Mechanics
4
07-25-18 01:24 PM
IrishBrewer
Bicycle Mechanics
15
01-10-17 01:40 PM
3speed
Classic & Vintage
30
08-03-12 06:49 AM
poprad
Classic & Vintage
8
11-13-11 03:17 PM
hospadar
Bicycle Mechanics
3
06-14-10 07:33 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.