Go Back  Bike Forums > Bike Forums > Folding Bikes
Reload this Page >

[Front crankset] Replacing outer ring with chain guard?

Notices
Folding Bikes Discuss the unique features and issues of folding bikes. Also a great place to learn what folding bike will work best for your needs.

[Front crankset] Replacing outer ring with chain guard?

Old 05-20-20, 01:10 AM
  #1  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
[Front crankset] Replacing outer ring with chain guard?

Hello,

I'm currently using a 50/40/30 triple crankset + derailleur on a Brompton where I 1) removed the outer 50T, and 2) replaced the middle ring with a 46T.

I'd like to install a chain guard as the outer ring.

Would this product work if I chose the "use on double chainring" option? Should I order a 46T, 48T, or 50T?

Out of curiosity, how do the single/double chainring models differ? Why two models?

Thank you.


Last edited by Winfried; 05-20-20 at 01:14 AM.
Winfried is offline  
Likes For Winfried:
Old 05-20-20, 06:44 PM
  #2  
2_i 
Senior Member
 
Join Date: Sep 2005
Location: Michigan
Posts: 3,693

Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 834 Post(s)
Liked 332 Times in 247 Posts
It seems that I am using the rule of 4T more for the guard than the largest ring. Note that these guard rings are relatively heavy. A lighter option would be a ring that meant to work with a plastic guard, if you can find one in your desired size. As to to a dedicated guard for single vs double crankset, it might be the issue of space for the crank. (When necessary you could always trim the ring on your own.) It could be also an issue of mounting bolts, but they mention none in their offer.
2_i is offline  
Old 05-21-20, 04:32 PM
  #3  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
Thanks. I'll try and find one made of plastic instead.
Winfried is offline  
Old 05-21-20, 07:46 PM
  #4  
1nterceptor
LET'S ROLL
 
1nterceptor's Avatar
 
Join Date: Nov 2009
Location: NEW YORK, NY - USA
Posts: 4,782

Bikes: 2014 BMC Gran Fondo, 2013 Brompton S6L-X

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 306 Post(s)
Liked 44 Times in 33 Posts
I've seen folks grind the teeth of the outer rings on a double; making it a guard/protector.
1nterceptor is offline  
Old 05-22-20, 09:45 AM
  #5  
rhenning
Senior Member
 
Join Date: Apr 2006
Posts: 3,653
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 380 Post(s)
Likes: 0
Liked 106 Times in 80 Posts
I think this is funny but a couple of years ago I need a chain guard for on of my folders that had a broken plastic chain guard. I actually made a chain guard out of a 54 tooth chain ring that I filed the teeth off of. Roger
rhenning is offline  
Old 05-22-20, 05:46 PM
  #6  
Tourist in MSN
Senior Member
 
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,112

Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.

Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 3426 Post(s)
Liked 1,441 Times in 1,122 Posts
Originally Posted by 1nterceptor
I've seen folks grind the teeth of the outer rings on a double; making it a guard/protector.
Originally Posted by rhenning
I think this is funny but a couple of years ago I need a chain guard for on of my folders that had a broken plastic chain guard. I actually made a chain guard out of a 54 tooth chain ring that I filed the teeth off of. Roger
I used a saber saw. I bought a cheap chainring that was a lot cheaper than a chainguard ring. Cut the teeth off with a saber saw. That of course left a rough cut. Put the ring on the crank arm and hand turned the crank for about 10 or maybe 15 minutes while I held a file on the rough cut until it was quite smooth.

Saber saw, I used a fine tooth metal blade, the aluminum clogged up the teeth, I might have used two blades. But I had plenty of blades so that was not a problem.

Aluminum is not that heavy, works well for me.

Photo is old, later I decided to spray it black to match all the other black stuff. This is obviously not a folder. The chainring I cut was a 52T, the chainring behind it in the inner position on the double crank is a 44T. The guard is a bit bigger than ideal, but it is close enough that I have no desire to replace it.


Tourist in MSN is offline  
Likes For Tourist in MSN:
Old 05-22-20, 08:38 PM
  #7  
2_i 
Senior Member
 
Join Date: Sep 2005
Location: Michigan
Posts: 3,693

Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 834 Post(s)
Liked 332 Times in 247 Posts
Originally Posted by Winfried
Thanks. I'll try and find one made of plastic instead.
I looked at a few of of the Driveline guards around the home and Litepro on-line and the formula for their diameter seems to be D=0.4cm*(No of teeth)+1.1cm. Stacking this against the 22.3cm diameter of the plastic guard that Brompton provides for their 50T ring yields 53T or 3T more than the largest ring. I.e., one should be able to go with just 3T more than the largest ring. Also looking around the home and on-line, some of the alu rings seem well lighter than other. though presumably not as a tough.

Last edited by 2_i; 05-23-20 at 06:09 AM. Reason: Corrected D: 22.3mm->22.3cm
2_i is offline  
Likes For 2_i:
Old 05-23-20, 04:09 AM
  #8  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
Thanks!

You meant 22.3 cm.

Last edited by Winfried; 05-23-20 at 05:07 AM.
Winfried is offline  
Likes For Winfried:
Old 05-23-20, 08:35 AM
  #9  
Schwinnsta
Schwinnasaur
 
Schwinnsta's Avatar
 
Join Date: Dec 2006
Location: New Orleans, LA
Posts: 1,557
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 450 Post(s)
Liked 170 Times in 116 Posts

👍
Schwinnsta is offline  
Likes For Schwinnsta:
Old 05-23-20, 07:50 PM
  #10  
wesgreen
Full Member
 
Join Date: Nov 2015
Posts: 223
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 80 Post(s)
Liked 36 Times in 28 Posts
Maybe cutting and drilling into an old frisbee would work, if it's flat enough.
wesgreen is offline  
Old 05-24-20, 05:49 PM
  #11  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
I had a BCD110 50T chainring handy, and it looks like I do need the equivalent of a 52T to cover the 46T outer chainring + chain.

I'm unclear at how chain guards sit on spiders. Do they come/require longer nuts so they can sit on top of the single/outer ring?

Winfried is offline  
Old 05-24-20, 05:50 PM
  #12  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
Originally Posted by Schwinnsta

👍
Is it a double, with the outer ring used for the chain guard?
Winfried is offline  
Old 05-24-20, 06:25 PM
  #13  
Schwinnsta
Schwinnasaur
 
Schwinnsta's Avatar
 
Join Date: Dec 2006
Location: New Orleans, LA
Posts: 1,557
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 450 Post(s)
Liked 170 Times in 116 Posts
Originally Posted by Winfried
Is it a double, with the outer ring used for the chain guard?
Yes. I have had for a long time. I think it might have been off a Campi, but I am not sure. I made one for a different bike too. As I recall, the teeth snap off and leave a little that must be filed or ground round to line and a little bit must be ground to get a better fit to where it attaches, kind of an undercut where it attaches to the crank just on the back edge.
Schwinnsta is offline  
Old 05-24-20, 07:04 PM
  #14  
Winfried
Senior Member
Thread Starter
 
Winfried's Avatar
 
Join Date: Aug 2011
Location: Paris, France
Posts: 2,494
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 116 Times in 98 Posts
I'll just get the 52T chain guard and see how it goes. At €20, it's not worth trying to file down a chainring.
Winfried is offline  
Likes For Winfried:
Old 05-24-20, 07:25 PM
  #15  
2_i 
Senior Member
 
Join Date: Sep 2005
Location: Michigan
Posts: 3,693

Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 834 Post(s)
Liked 332 Times in 247 Posts
Originally Posted by Winfried
I'll just get the 52T chain guard and see how it goes.
Relative to other alu guards, this one is light. You mount it with the same hardware as regular rings. Since you should have the original bolts for the triple, you should have no problem there. The real problem is when you mount such a guard as a third ring on a double or fourth on a triple, as then you need the not very common extra long bolts.
2_i is offline  
Likes For 2_i:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.