Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Identifying old bottom bracket and correct tool

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Identifying old bottom bracket and correct tool

Old 02-05-18, 09:00 PM
  #1  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
Identifying old bottom bracket and correct tool

I have a bike that's a mish-mash of parts most of which are from the early eighties. The bottom bracket on the non-drive side has a lock ring with six notches. What tool can I use to remove this? It needs to be rebuilt. On the lock ring it says "Nikyo Made in Japan 1.37 x 24T". I'm assuming that the 1.37 x 24T is a diameter and tpi from what I can gather. Has anyone heard of Nikyo? Would the Hozan C-205 unlock this?
kjaioqhbkqb is offline  
Old 02-05-18, 09:10 PM
  #2  
JanMM
rebmeM roineS
 
JanMM's Avatar
 
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,217

Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 653 Post(s)
Liked 345 Times in 225 Posts
That Hozan tool should work. If all else fails, a nail set and a hammer would work, but not as well as the correct tool. Looks similar to the Sugino tool I used in the past.
Yes, that is the BB threading. Gonna replace with cartridge BB?
Attached Images
File Type: jpg
a2aa_sugino_hook.jpg (7.3 KB, 278 views)
__________________
Bacchetta Giro A20, RANS V-Rex, RANS Screamer

Last edited by JanMM; 02-05-18 at 10:46 PM.
JanMM is offline  
Old 02-05-18, 11:53 PM
  #3  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,824

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,231 Times in 852 Posts
Or maybe a Park Tools HCW-5?

If the notches are "buggered up", a larger water pump pliers.
Bill Kapaun is online now  
Old 02-06-18, 01:59 AM
  #4  
Ghrumpy
Senior Member
 
Join Date: Jul 2009
Posts: 790
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times in 6 Posts
Originally Posted by kjaioqhbkqb
I'm assuming that the 1.37 x 24T is a diameter and tpi from what I can gather.
Exactly correct. That is a British Standard Cycle (BSC) thread.

The Hozan C-205 "Rock Ring Wrench" should have no problem with that. Even better are the Hozan C-203 pliers.
Ghrumpy is offline  
Old 02-06-18, 02:02 AM
  #5  
SkyDog75
Senior Member
 
Join Date: May 2011
Location: Upstate NY
Posts: 3,794

Bikes: Bianchi San Mateo and a few others

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 634 Post(s)
Likes: 0
Liked 13 Times in 9 Posts
Originally Posted by kjaioqhbkqb
The bottom bracket on the non-drive side has a lock ring with six notches. What tool can I use to remove this? ... Would the Hozan C-205 unlock this?
A lockring wrench like a Park Tool HCW-5 or Hozan C-205 would be an appropriate tool for the lockring. When assembling and/or adjusting the bottom bracket, you’ll also need something to turn/hold the bearing cup. The cup will have some type of tool interface machined into it — maybe a slot, a hex head, or a series of holes for a pin spanner like a Park Tool SPA-1.

Originally Posted by kjaioqhbkqb
On the lock ring it says "Nikyo Made in Japan 1.37 x 24T". I'm assuming that the 1.37 x 24T is a diameter and tpi from what I can gather.
Yes, and that diameter & threading identify the unit as a common English-threaded bottom bracket.
SkyDog75 is offline  
Old 02-06-18, 07:05 AM
  #6  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
@JanMM Thanks. My concern with the tools was that I wasn't sure if the diameter needed to be an exact match. But I just looked at the Hozan website and they show the C-205 in use and in the picture the tool has a smaller diameter than the lock ring, so I guess it isn't a problem. ... Probably I'm going to replace the bearings and just pick up another square taper of the same kind through eBay or something. I'm not sure that I'll switch to a cartridge. I like the old stuff. I started riding a few hundred miles a month and I'm now discovering all of these issues coming up for maintenance though. Not sure if bearings in a cartridge etc. would give me more life down there.

@Ghrumpy Ah, yes. The pliers look more universal.

@SkyDog75 Thank you. I see the series of holes now. I have a Park spanner wrench for my SunTour Perfect freewheel. I'll check that it fits the bottom bracket holes too.
kjaioqhbkqb is offline  
Old 02-06-18, 07:47 AM
  #7  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by Ghrumpy
Even better are the Hozan C-203 pliers.
Or the VAR #16:



If you're on a budget, a standard set of slip-jaw pliers can be converted into a serviceable copy of the Hozan pliers:

DIY Lockring Pliers: 3 Steps (with Pictures)
JohnDThompson is online now  
Old 02-06-18, 08:42 AM
  #8  
grizzly59
Senior Member
 
Join Date: Aug 2016
Posts: 712
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 283 Post(s)
Liked 262 Times in 164 Posts
These are my tools for old bottom brackets. If you replace, you'll need to remove the lock ring and the fixed cup. Your fixed cup is prob left-hand thread. And you prob need a new tool for the lock rings on the new BB. The pin spanners are for adjusting the left cup, you don't need them if you're switching to a cartridge BB. I cant find any part #'s, standard Sugino tools. Green spanner is a Park. Google Sheldon Brown bottom brackets
Attached Images
File Type: jpg
bbtools2.jpg (122.1 KB, 253 views)
grizzly59 is offline  
Old 02-06-18, 09:14 AM
  #9  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
Originally Posted by grizzly59
Your fixed cup is prob left-hand thread.
No, your fixed (drive side) cup is certainly left-hand threaded. All English threaded bottom brackets have left-handed threads on the drive side of the bottom bracket.
HillRider is offline  
Old 02-06-18, 02:36 PM
  #10  
Ghrumpy
Senior Member
 
Join Date: Jul 2009
Posts: 790
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times in 6 Posts
Originally Posted by JohnDThompson
Or the VAR #16:

Well, yes, that's the Cadillac of lockring tools.

Originally Posted by JohnDThompson
If you're on a budget, a standard set of slip-jaw pliers can be converted into a serviceable copy of the Hozan pliers:

DIY Lockring Pliers: 3 Steps (with Pictures)
Dang. Wish I'd thought of that before I bought my VAR. (OK, I would have bought the VAR anyway.)
The nice thing about the Hozan pliers is that they have rounded jaws, not flat, so they do less damage and grip round things better, should you have to resort to that method.
Ghrumpy is offline  
Old 02-07-18, 09:28 AM
  #11  
Spaghetti Legs 
Senior Member
 
Join Date: Dec 2014
Location: Central Virginia
Posts: 5,085

Bikes: Numerous

Mentioned: 150 Post(s)
Tagged: 0 Thread(s)
Quoted: 1672 Post(s)
Liked 3,034 Times in 904 Posts
My Campy lock ring tool works pretty nicely. Before that my primary tool was the Park lockring spanner and it was average at best. I frequently used a small metal punch and a hammer to loosen the lockring to avoid stripping it with the Park tool.
__________________
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur

Spaghetti Legs is offline  
Old 02-07-18, 02:23 PM
  #12  
Ghrumpy
Senior Member
 
Join Date: Jul 2009
Posts: 790
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times in 6 Posts
Originally Posted by Spaghetti Legs
My Campy lock ring tool works pretty nicely. Before that my primary tool was the Park lockring spanner and it was average at best. I frequently used a small metal punch and a hammer to loosen the lockring to avoid stripping it with the Park tool.
As far as lockring spanners, go, the Campy is great because it engages five notches instead of one. But it doesn't fit all lockrings; some are too big. And some lockrings have more or fewer than six notches.
Ghrumpy is offline  
Old 02-07-18, 06:30 PM
  #13  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
I went with the Hozan C-205. It's fine. The radius of the tool doesn't exactly match the radius of the lock ring but it's functional.

My Park spanner wrench for my freewheel also works for the adjustable cup on the non-drive / lock ring side.

Now I need a fixed cup wrench. Hozan, VAR, ...?
kjaioqhbkqb is offline  
Old 02-07-18, 09:28 PM
  #14  
SkyDog75
Senior Member
 
Join Date: May 2011
Location: Upstate NY
Posts: 3,794

Bikes: Bianchi San Mateo and a few others

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 634 Post(s)
Likes: 0
Liked 13 Times in 9 Posts
Originally Posted by kjaioqhbkqb
Now I need a fixed cup wrench. Hozan, VAR, ...?
...or a 15” Crescent wrench, among other possibilities.
SkyDog75 is offline  
Old 02-08-18, 07:23 AM
  #15  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by kjaioqhbkqb
Now I need a fixed cup wrench. Hozan, VAR, ...?
What does the fixed cup look like? If it follows the Campagnolo standard, one of the aforementioned Park or Sugino hook spanners will have a fixed cup opening opposite the hook.



Otherwise, the Sheldon Brown universal tool is an option:


Tool Tips--Bottom Bracket Cups

Or the professional version of the Sheldon Brown tool:


https://www.efficientvelo.com/produc...b-cup-remover/
JohnDThompson is online now  
Old 02-08-18, 01:05 PM
  #16  
3alarmer 
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26249 Post(s)
Liked 10,231 Times in 7,100 Posts
Originally Posted by kjaioqhbkqb

Now I need a fixed cup wrench. Hozan, VAR, ...?
...unless you plan on replacing it with something else (like a new complete BB unit), you're well advised to clean it well while leaving it in place. If you simply must remove it for purposes of replacement, the Hozan fixed cup removal tool is about as bombproof as you can get in this department, but it's not cheap.

You can get pretty good results in most cases by through bolting some fender washers (big ones) on both sides of the BB so that the ones on the fixed cup side hold one of those Campy type fixed cup wrenches on the flats, with just a teeny bit of play. This holds the wrench onto the cup so it won't jump off when you hit it with a mallet or a dead blow hammer....the poor person's version of an impact wrench. Use penetrant on both sides of the BB shell/cup interface.

There's a photo of the setup somewhere in the tips and tricks thread, which you might get lucky and fine with Google.
3alarmer is offline  
Old 02-09-18, 02:20 AM
  #17  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
I think the fixed cup is 36mm.
kjaioqhbkqb is offline  
Old 02-11-18, 08:37 PM
  #18  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
@JohnDThompson @3alarmer The fixed cup has flats spaced 36mm apart.

Now that I have the adjustable cup off I can see what's happened. The adjustable cup is cracked. When I peer inside the 68mm bottom bracket shell I can see that the fixed cup is cracked too around the race. Both are pitted.

The black spindle says 3R Boron J-6 and is longer on the drive side to accommodate the three chain rings I think. The overall length of the spindle excluding the threads is about 128.5mm. The cups/races on the spindle are pitted and worn unevenly which is evident from the silver path the bearings traced out.

The 1/4" bearings (with huge flat spots) fell easily out of the cages, one of which was bent oblong.

Can this spindle be easily replaced? Does the 3R Boron J-6 indicate the sizing including the sizing of the longer drive side?

I like parts to be serviceable, so I prefer to rebuild here with same parts versus purchasing a disposable bottom bracket.
kjaioqhbkqb is offline  
Old 02-11-18, 09:06 PM
  #19  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
"3R Boron J-6" doesn't follow typical spindle markings, so replacing it will be a matter of taking a number of measurements and matching them against other spindles:



Good luck!
JohnDThompson is online now  
Old 02-11-18, 09:31 PM
  #20  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,824

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,231 Times in 852 Posts
Originally Posted by kjaioqhbkqb
.......The black spindle says 3R Boron J-6 and is longer on the drive side to accommodate the three chain rings I think.......
3R is the size code-
129mm long w/42 & 35mm offsets. (aka really long)

The "B" dimension in John's pic is 52mm.
Possibly the N3U will still be long enough for your cranks to clear the stays AND the FDER can move in a bit more.
Remember, you can swap ends.
You MUST keep to a "3" series. 5 or 7 or?? will not work. The "B" dimension is different.
Husky Bicycles: Bottom Bracket Parts
Attached Files
File Type: pdf
is.1131.2006-010.pdf (29.5 KB, 12 views)

Last edited by Bill Kapaun; 02-11-18 at 09:44 PM.
Bill Kapaun is online now  
Old 02-11-18, 09:52 PM
  #21  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
@Bill Kapaun The table helps. Thanks. Are these spindles still being made? What about the adjustable and fixed cups? The brand I had apparently was Nikyo.
kjaioqhbkqb is offline  
Old 02-11-18, 10:05 PM
  #22  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,824

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,231 Times in 852 Posts
Originally Posted by kjaioqhbkqb
@Bill Kapaun The table helps. Thanks. Are these spindles still being made? What about the adjustable and fixed cups? The brand I had apparently was Nikyo.
Did you think to poke around the site where I linked the spindles?
Bill Kapaun is online now  
Old 02-12-18, 11:12 AM
  #23  
3alarmer 
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26249 Post(s)
Liked 10,231 Times in 7,100 Posts
Originally Posted by kjaioqhbkqb
[MENTION=20548]I like parts to be serviceable, so I prefer to rebuild here with same parts versus purchasing a disposable bottom bracket.
Originally Posted by kjaioqhbkqb
@Bill Kapaun The table helps. Thanks. Are these spindles still being made? What about the adjustable and fixed cups? The brand I had apparently was Nikyo.
....I know this will seem counter intuitive to you, but I will mention it anyway. The day of readily available loose ball bottom bracket parts such as the various spindles and cups you need to accomplish rebuilding with similar parts is long past. It was hard to do even over at the bike co-op, where we had a whole box of old used spindles and miscellaneous cups.

The world of available parts has moved on to sealed unit BB replacements. In your case, do yourself a big favor and when you get that fixed cup out, make certain you measure the width of the BB shell, the length of the spindle, and understand the threading standard you require for the cups. Then order a readily available square taper BB replacement sealed unit (don't get the cheapest one, but you can get good quality in the 20-40 dollar range), repair your bicycle, and move on with riding it.

That's what I would do. In fact, I have done it a number of times. I don't even think anyone is manufacturing loose ball BB spindles or cups any more (but I might be wrong).
3alarmer is offline  
Old 02-13-18, 01:01 PM
  #24  
JanMM
rebmeM roineS
 
JanMM's Avatar
 
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,217

Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 653 Post(s)
Liked 345 Times in 225 Posts
Originally Posted by 3alarmer
....I know this will seem counter intuitive to you, but I will mention it anyway. The day of readily available loose ball bottom bracket parts such as the various spindles and cups you need to accomplish rebuilding with similar parts is long past. It was hard to do even over at the bike co-op, where we had a whole box of old used spindles and miscellaneous cups.

The world of available parts has moved on to sealed unit BB replacements. In your case, do yourself a big favor and when you get that fixed cup out, make certain you measure the width of the BB shell, the length of the spindle, and understand the threading standard you require for the cups. Then order a readily available square taper BB replacement sealed unit (don't get the cheapest one, but you can get good quality in the 20-40 dollar range), repair your bicycle, and move on with riding it.

That's what I would do. In fact, I have done it a number of times. I don't even think anyone is manufacturing loose ball BB spindles or cups any more (but I might be wrong).
This would be easier now and easier in the future.
__________________
Bacchetta Giro A20, RANS V-Rex, RANS Screamer
JanMM is offline  
Old 03-20-18, 04:15 PM
  #25  
kjaioqhbkqb
Junior Member
Thread Starter
 
Join Date: Feb 2018
Location: Fremont, CO
Posts: 81
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 9 Times in 8 Posts
Thank you all. I decided to have the LBS remove the fixed cup for me. Tange still makes the spindles and cups I needed according to the LBS and so I went with that. The result is perfect.

Now that I've been through this I'm less hesitant to try something different. So next time I'll probably switch to a sealed unit.
kjaioqhbkqb is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
adrian089
Classic & Vintage
21
10-07-18 09:25 PM
awunder
Bicycle Mechanics
3
05-19-16 09:45 AM
cbender
Classic & Vintage
33
05-21-15 04:15 PM
FieldEffect
Bicycle Mechanics
18
01-13-12 02:02 PM
dansenior
Bicycle Mechanics
5
05-12-10 11:25 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.