Loose headset damage
#1
Junior Member
Thread Starter
Join Date: Oct 2007
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Loose headset damage
I need to replace a damaged headset that has developed brinelling. This is the bike's second headset that has developed this kind of damage, and I have concluded my initial adjustment of freshly packed bearings must actually be too loose as the grease settles. Therefore I plan to tighten the adjusting cup about an 1/8 turn more than I would previously and/or be ready to readjust the bearings after the first week of riding.
The current headset is the more decorative Tange which does not have the smallest stack height and would like an identical replacement. Uncertainty arises with the different models, chrome vs alloy and which is more durable and whether the alloy type has any advantages other than less weight. Scanning ebay these are the listings I found compatible with a Japanese bike (nishiki) with 27.0mm crown race ID:
alloy:
lv1500
NJS
chrome (NJS)
I am not sure if the first two are the same, both being alloy, perhaps simply titled differently. I usually found chrome headsets to be about half the price of comparable alloy versions, but not in this case for what is currently showing on ebay. If there are no real advantages to an alloy headset for durability, another chrome (adjusted a bit more tightly) seems best as I also prefer the smoother finish.
By the way, if a slightly loose bearing develops pitting, what is the effect of a headset adjusted on the side of being tight?
The current headset is the more decorative Tange which does not have the smallest stack height and would like an identical replacement. Uncertainty arises with the different models, chrome vs alloy and which is more durable and whether the alloy type has any advantages other than less weight. Scanning ebay these are the listings I found compatible with a Japanese bike (nishiki) with 27.0mm crown race ID:
alloy:
lv1500
NJS
chrome (NJS)
I am not sure if the first two are the same, both being alloy, perhaps simply titled differently. I usually found chrome headsets to be about half the price of comparable alloy versions, but not in this case for what is currently showing on ebay. If there are no real advantages to an alloy headset for durability, another chrome (adjusted a bit more tightly) seems best as I also prefer the smoother finish.
By the way, if a slightly loose bearing develops pitting, what is the effect of a headset adjusted on the side of being tight?
#2
Junior Member
Thread Starter
Join Date: Oct 2007
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Also, I am trying to replace this headset before riding the bike much after a LBS owner mentioned how a loose headset can cause deformities to the headtube over time. Not sure if this applies in this case with the headset loose only to the point of feeling a bit play while holding the front brake and rocking the bike, and only while the handlebars are pointed straight forward, the most common riding position -- is this notion of damaging a frame with a slightly loose headset unfounded?
#3
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
If you're looking for a durable headset, get one with roller bearings in the lower race rather than balls, e.g.:
Roller Drive Threaded Headset ? Interloc Racing Design / IRD
Riding with a loose threaded headset likely won't damage the frame, but it can damage the fork, as the threaded cup can erode the threads on the steer tube if the headset isn't properly adjusted.
Roller Drive Threaded Headset ? Interloc Racing Design / IRD
Riding with a loose threaded headset likely won't damage the frame, but it can damage the fork, as the threaded cup can erode the threads on the steer tube if the headset isn't properly adjusted.
#4
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,837
Bikes: 2016 Fuji Tread, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 676 Post(s)
Liked 741 Times
in
430 Posts
Maybe the LBS guy was talking about the fit of the cup into the frame, not the bearing adjustment.
If your wear is just where a few bearings sit, that's too loose. If it were too tight, you might see damage all around the circumference, but I'm just guessing since I've never seen that in a headset. If a headset were too tight, I think the handling would be objectionable.
Your plan to readjust is a good one. Better to be just a tad on the tight side to properly load the bearing.
Is this a road/commuter bike? Lots of miles on it?
If your wear is just where a few bearings sit, that's too loose. If it were too tight, you might see damage all around the circumference, but I'm just guessing since I've never seen that in a headset. If a headset were too tight, I think the handling would be objectionable.
Your plan to readjust is a good one. Better to be just a tad on the tight side to properly load the bearing.
Is this a road/commuter bike? Lots of miles on it?
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
Alloy VS steel- Alloy is lighter, generally found in mid to better grade (not cheap entry level) and with sealing features beyond any found in a cartridge bearing, made from softer material (easier on the frame/fork but also easier to strip the threads with). Steel is found across the entire grade range, often at a lower price then a matching alloy version, often not found with a cartridge bearing or added sealing, stronger threads and not as easily rounded off nut flats,
I mention the thread strength because one of the more common repairs I make on alloy headsets that have been used loose is to replace the top/lock nut due to it's threads being damaged from the rocking about on the steel fork's steerer. Even these days we sell a number of steel top/lock nuts a year. Andy
I mention the thread strength because one of the more common repairs I make on alloy headsets that have been used loose is to replace the top/lock nut due to it's threads being damaged from the rocking about on the steel fork's steerer. Even these days we sell a number of steel top/lock nuts a year. Andy
__________________
AndrewRStewart
AndrewRStewart
#6
Senior Member
The LBS guy was talking about bearing adjustment. If there's play in the bearings, then the impacts that headsets deal with all the time aren't being distributed nicely across the full race, they'll be hammering the front and back of the races. That's bad for both the bearings and the thing they're sitting in.
#7
Senior Member
I have replaced several 1" headsets with Tange Levin NJS. They are an appropriate looking replacement for vintage bikes, and they are excellently built, but, you are going to pay for that "NJS" designation.
They make a less ornate, non-NJS-certified headset for a paltry ~$25. It is available both in ISO and JIS.
Assuming this is for a road bike, and the headset is properly adjusted, the damage you have was probably caused by lack of lubrication replenishment. Searching for 'false brinelling' will lead to plenty of information about this. For what it's worth, the same kind of damage happens in suspension bearings on mountain bikes.
They make a less ornate, non-NJS-certified headset for a paltry ~$25. It is available both in ISO and JIS.
Assuming this is for a road bike, and the headset is properly adjusted, the damage you have was probably caused by lack of lubrication replenishment. Searching for 'false brinelling' will lead to plenty of information about this. For what it's worth, the same kind of damage happens in suspension bearings on mountain bikes.
#8
Senior Member
The damage is from fretting and a poor design for the application. This one a or a CrissKing solves the problem. https://www.ebay.com/itm/New-Old-Sto....c100752.m1982
#9
Industry guy
Have you had the head tube faced?
The precision of fit after a proper facing will allow the cups to seat properly and will provide parallel
bearing surfaces.
Check the location of the brinelling i.e. is the it oriented or more significant in one area?
Makes even a mediocre headset perform better.
The precision of fit after a proper facing will allow the cups to seat properly and will provide parallel
bearing surfaces.
Check the location of the brinelling i.e. is the it oriented or more significant in one area?
Makes even a mediocre headset perform better.
#10
Senior Member
And this is the best one. https://chrisking.com/collections/2n...=8277576712237
#11
Senior Member
An eighth of a turn is absolutely enormous when adjusting headsets. If that's your idea better to take this to a mechanic. Overtightened headsets fail very quickly.
#12
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,904
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,928 Times
in
2,553 Posts
Yes, the headtube should have been faced. If it has not, have it done. I use all steel Tanges, model governed by stack height needed. Levins are nice but even the cheap $8 OEM headsets are good except there are no seals. (Quite usable in good weather or with fenders and marine grease.)
I get ~8000 miles per Tange HS. Another 1-2000 after upping the balls one size. For $30 and one adjustment/year (tighten 1/8th turn), I call it good.
Edit: I wrote 1/8th turn before reading the last post. 1/16th might be closer. I DO NOT get my HSs too tight.
Ben
I get ~8000 miles per Tange HS. Another 1-2000 after upping the balls one size. For $30 and one adjustment/year (tighten 1/8th turn), I call it good.
Edit: I wrote 1/8th turn before reading the last post. 1/16th might be closer. I DO NOT get my HSs too tight.
Ben
#13
Senior Member
Best HS adjustment instructions ever are here:
https://www.spectrum-cycles.com/mechanical.php
Scroll down to middle of page.
Head tubes ovalize when there is loose play to level of banging. Definitely happens, not that common. Just as often a loose HS and some impacts will bow the steerer. Which can be harder to fix than the oval headtube. OTOH a very slightly, I mean slightly, loose HS is the one that will last more or less indefinitely. No such thing as preload on a HS. Any tightness, one degree of tightness, you have a head bearing about to fail. Most head bearings do fail in short order, but they can be ridden a long time brinneled without anyone noticing. Exact same HS, any brand or model, adjusted perfect lasts forever. Raleigh headsets that were less than a dollar BITD could last as long as a Campy. Really cheap HS with stamped cups give long service if cared for. Perfect doesn't that much happen and you don't have to beat yourself up if not achieved.
Ten thousand on a Tange sounds short to me but I have sure done worse. If getting that consistently whatever you are doing is darn close and leave it alone.
Poster who claims not to have seen dented headsets needs to ride more.
Giving up on cup and cone heads and using needle bearings/cartridge bearings is reasonable. There are still millions of cup and cone bearings out there and mechanics should know how.
https://www.spectrum-cycles.com/mechanical.php
Scroll down to middle of page.
Head tubes ovalize when there is loose play to level of banging. Definitely happens, not that common. Just as often a loose HS and some impacts will bow the steerer. Which can be harder to fix than the oval headtube. OTOH a very slightly, I mean slightly, loose HS is the one that will last more or less indefinitely. No such thing as preload on a HS. Any tightness, one degree of tightness, you have a head bearing about to fail. Most head bearings do fail in short order, but they can be ridden a long time brinneled without anyone noticing. Exact same HS, any brand or model, adjusted perfect lasts forever. Raleigh headsets that were less than a dollar BITD could last as long as a Campy. Really cheap HS with stamped cups give long service if cared for. Perfect doesn't that much happen and you don't have to beat yourself up if not achieved.
Ten thousand on a Tange sounds short to me but I have sure done worse. If getting that consistently whatever you are doing is darn close and leave it alone.
Poster who claims not to have seen dented headsets needs to ride more.
Giving up on cup and cone heads and using needle bearings/cartridge bearings is reasonable. There are still millions of cup and cone bearings out there and mechanics should know how.
#14
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
If you're looking for a durable headset, get one with roller bearings in the lower race rather than balls, e.g.:
Roller Drive Threaded Headset ? Interloc Racing Design / IRD
Riding with a loose threaded headset likely won't damage the frame, but it can damage the fork, as the threaded cup can erode the threads on the steer tube if the headset isn't properly adjusted.
Roller Drive Threaded Headset ? Interloc Racing Design / IRD
Riding with a loose threaded headset likely won't damage the frame, but it can damage the fork, as the threaded cup can erode the threads on the steer tube if the headset isn't properly adjusted.
For handling fore-aft vibration movement, these bearings are worse than angular contact ball bearings.
They can help those with high speed bar shimmy problem - since they provide a bit more drag (and hence rotation damping). But for durability, I wouldn't bet on these over good quality angular contact ball bearings.
My 2c on bicycle bearing types.
Adjusting threadless headset preload.
Last edited by Bike Gremlin; 03-22-19 at 01:05 AM.
#15
Junior Member
Thread Starter
Join Date: Oct 2007
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
OTOH a very slightly, I mean slightly, loose HS is the one that will last more or less indefinitely. No such thing as preload on a HS. Any tightness, one degree of tightness, you have a head bearing about to fail. Most head bearings do fail in short order, but they can be ridden a long time brinneled without anyone noticing.
Alloy VS steel- Alloy is lighter, generally found in mid to better grade (not cheap entry level) and with sealing features beyond any found in a cartridge bearing, made from softer material (easier on the frame/fork but also easier to strip the threads with). Steel is found across the entire grade range, often at a lower price then a matching alloy version, often not found with a cartridge bearing or added sealing, stronger threads and not as easily rounded off nut flats,
I mention the thread strength because one of the more common repairs I make on alloy headsets that have been used loose is to replace the top/lock nut due to it's threads being damaged from the rocking about on the steel fork's steerer. Even these days we sell a number of steel top/lock nuts a year. Andy
I mention the thread strength because one of the more common repairs I make on alloy headsets that have been used loose is to replace the top/lock nut due to it's threads being damaged from the rocking about on the steel fork's steerer. Even these days we sell a number of steel top/lock nuts a year. Andy
Have you had the head tube faced?
The precision of fit after a proper facing will allow the cups to seat properly and will provide parallel
bearing surfaces.
Check the location of the brinelling i.e. is the it oriented or more significant in one area?
Makes even a mediocre headset perform better.
The precision of fit after a proper facing will allow the cups to seat properly and will provide parallel
bearing surfaces.
Check the location of the brinelling i.e. is the it oriented or more significant in one area?
Makes even a mediocre headset perform better.
Last edited by joedab; 03-26-19 at 10:15 AM.
#16
Senior Member
Join Date: Jul 2017
Location: Queens, NY for now...
Posts: 1,515
Bikes: 82 Lotus Unique, 86 Lotus Legend, 88 Basso Loto, 88 Basso PR, 89 Basso PR, 96 Bianchi CDI, 2013 Deda Aegis, 2019 Basso Diamante SV
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 172 Times
in
113 Posts
And this is the best one. https://chrisking.com/collections/2n...=8277576712237
#17
Senior Member
Just to clarify, I said 1/8 in an offhanded way but what I really meant was something more like 1/16. As alluded to above, I am starting to lean toward the idea of a very slightly preloaded bearing idea. Also, to advise someone who is working to refine their understanding/technique instead to visit a professional is ridiculous, not to mention antithetical to using this forum.
1/16 of a turn is still 22 degrees of turn, which is a crude coarse adjustment on a headset. This means you are not even beginning to get good adjustment. You're working like a truck mechanic. Try reading the link I gave you previously. It's from Tom Kellogg, whose reputation and experience as a mechanic are pretty well known. And he's a fair writer. When it seems that someone posting here is just not getting the drift and is set on doing things that will damage their bike, and take them in directions they don't want to go, yes, I will recommend using a professional. Antithetical? Sometimes it does seem like the idea here is everyone should learn by destroying fleets of bikes. Preload simply does not work on headsets. If you think it does you have not worked on headsets and are missing the point. Work on a few thousand headsets for a few decades and then inform us of your wisdom regarding preload or other subjects.
Or do it your way and get a bigger hammer.
1/16 of a turn is still 22 degrees of turn, which is a crude coarse adjustment on a headset. This means you are not even beginning to get good adjustment. You're working like a truck mechanic. Try reading the link I gave you previously. It's from Tom Kellogg, whose reputation and experience as a mechanic are pretty well known. And he's a fair writer. When it seems that someone posting here is just not getting the drift and is set on doing things that will damage their bike, and take them in directions they don't want to go, yes, I will recommend using a professional. Antithetical? Sometimes it does seem like the idea here is everyone should learn by destroying fleets of bikes. Preload simply does not work on headsets. If you think it does you have not worked on headsets and are missing the point. Work on a few thousand headsets for a few decades and then inform us of your wisdom regarding preload or other subjects.
Or do it your way and get a bigger hammer.
#18
Full Member
Although quality of the headset can be part of the problem, typically when I see the brinelling you are experiencing it is due to the headset being loose. When I assemble a headset after cleaning and greasing, I rotate the fork as I am snugging the headset. I tighten until I can feel it start to bind and then back off slowly intil it feals smooth. I then go for a test ride which should ensure that the bearings are well seated and check to make sure it has not loosened.
You should check the headset for play regularly as it literally takes a couple seconds.
You should check the headset for play regularly as it literally takes a couple seconds.
#19
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
So what problem was the brinelling causing you? Were you actually able to feel it while riding the bike? I haven't looked at my schwinn, but my raleigh and previous bikes had marks on the headset races that looked like brineling, but were probably just slight surface corrosion on the part of the race the bearing wasn't touching. I think I only found binelling for real on one headset ever, and it wasn't anything that was noticeable while riding.
#20
Senior Member
There is no brinelling in these bearings. It is a matter of fretting because of lack of motion relubing the balls.
https://www.sheldonbrown.com/brandt/...-steering.html
https://www.sheldonbrown.com/brandt/...-steering.html
#21
Senior Member
https://www.sheldonbrown.com/brandt/...-steering.html
#22
Senior Member
Join Date: Jul 2017
Location: Queens, NY for now...
Posts: 1,515
Bikes: 82 Lotus Unique, 86 Lotus Legend, 88 Basso Loto, 88 Basso PR, 89 Basso PR, 96 Bianchi CDI, 2013 Deda Aegis, 2019 Basso Diamante SV
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 172 Times
in
113 Posts
They are no better than any other old style headset bearings.
https://www.sheldonbrown.com/brandt/...-steering.html
https://www.sheldonbrown.com/brandt/...-steering.html
#23
Junior Member
Thread Starter
Join Date: Oct 2007
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
So what problem was the brinelling causing you? Were you actually able to feel it while riding the bike? I haven't looked at my schwinn, but my raleigh and previous bikes had marks on the headset races that looked like brineling, but were probably just slight surface corrosion on the part of the race the bearing wasn't touching. I think I only found binelling for real on one headset ever, and it wasn't anything that was noticeable while riding.
I have since tightened my headset just a skosh, enough to eliminate the play there was in the position with the brinelling, and although it probably favors this position to a greater degree, I feel good about this adjustment until I am able to replace the headset, since the lack of play should eliminate further pitting and any stress transferred to the headtube. The takeaway from this bearing casualty might be to readjust a new headset soon after installation especially if one has a tendency to err on the side of too much grease. My conception of a properly adjusted bearing is like balancing a razor's edge, being impossible to maintain with a number of factors that can move the position of this edge, and if the slightest amount of play can be the seed of bearing brinelling it would seem leaning toward a bit tight (preloaded) is better than anything loose or even 'perfect' since this can change over time.
#24
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
The headset brinelling is most noticeable when riding without hands where the free rotation of the front wheel of minute amounts is crucial. The way I test for brinelling is by holding the top tube of a bike on my shoulder, leaning the headtube down so the headset is able to sway like a pendulum. Knock the handlebars a bit and watch the motion .. if the front wheel tends to favor slowing and ultimately stopping/snapping to the centerline, the bearing has brinelling in this most common of positions. When riding no-handed, the wheel is resistant to tracking along a line other than center and therefore for a slight adjustment or curve, one need lean far enough to snap the bearings out of this indented position, which leads to a series of over-adjustments just to remain a desired course.
I have since tightened my headset just a skosh, enough to eliminate the play there was in the position with the brinelling, and although it probably favors this position to a greater degree, I feel good about this adjustment until I am able to replace the headset, since the lack of play should eliminate further pitting and any stress transferred to the headtube. The takeaway from this bearing casualty might be to readjust a new headset soon after installation especially if one has a tendency to err on the side of too much grease. My conception of a properly adjusted bearing is like balancing a razor's edge, being impossible to maintain with a number of factors that can move the position of this edge, and if the slightest amount of play can be the seed of bearing brinelling it would seem leaning toward a bit tight (preloaded) is better than anything loose or even 'perfect' since this can change over time.
I have since tightened my headset just a skosh, enough to eliminate the play there was in the position with the brinelling, and although it probably favors this position to a greater degree, I feel good about this adjustment until I am able to replace the headset, since the lack of play should eliminate further pitting and any stress transferred to the headtube. The takeaway from this bearing casualty might be to readjust a new headset soon after installation especially if one has a tendency to err on the side of too much grease. My conception of a properly adjusted bearing is like balancing a razor's edge, being impossible to maintain with a number of factors that can move the position of this edge, and if the slightest amount of play can be the seed of bearing brinelling it would seem leaning toward a bit tight (preloaded) is better than anything loose or even 'perfect' since this can change over time.
Generally agree, with one note:
When testing for play using a method of rocking the bike back and forth with the front brake locked, grease doesn't "mask up" any play, so there shouldn't be any need for re-adjustment, if it's done properly.
The swing method described is great for testing if there's too much preload.