“Golden Anniversary Ride” bike: 1974 Falcon
#1
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
“Golden Anniversary Ride” bike: 1974 Falcon
I think I mentioned earlier that in 1974, my friends and I all turned 18 and bought “decent” bikes; with next year being the 50th anniversary of that, I am restoring three of those bikes for my friends and plan some kind of celebratory ride for the four of us. Now that the weather is far less riding-friendly and I am indoors, it time to start.
First up is this 1974 Falcon. There are few things about identifying the bike a bit problematic, despite it being a one-owner bike. The shop where he bought it, well, I worked there that year for about 6 months that year, and all of the Falcons sold there were built up from bare frames with components chosen by the buyer and the staff — no two alike. And, I cannot claim to have the entire line-up memorized anyway. That other Falcon I did earlier this year, also 1974 and also from a childhood friend, had a nice spec with 531 butted tubes and Campy dropouts, and no chrome at all. This one has no-name dropouts (but they look “forged” to me and have an integral RD hanger) but the fork is chromed, as are the head lugs — and nowhere else. No clue which model. And, there’s a lot to clean up, it’s been hanging in a garage a long time.
Mish-mash of components: SR cranks, Campy NR derailleurs, Suntour barcons (I think I sold them to the owner later, after I tired of them), Fiamme bars and stem, Weinmann centerpulls, Brooks Pro saddle on a straight steel post (!) The wheels are plain Normandys and 27” steel rims, he and I seem to recall he quickly decided to ditch the tubulars and these were the only wheels I had hanging around in my basement at the time.
Mostly it needs rehab, all cleaned/polished/lubed/assembled. The wheels go away, as I have a spare set of 700C alloys with Campy hubs to donate; and that gas-pipe seat post must go (my micrometer suggests 26.4mm despite being quite out-of-round, does that sound right?)
It took much of the day to break it down to the last nut-bolt-and-washer. Hey, I found I had one of those Campy pedal cap wrenches! And, oddly, the front brake had 10mm pivot bolts, and the rears were 11mm? Of course the “most fun” were getting the springs disengaged on the derailleurs and calipers, and I am sure to be cursing when the time for reassembling them comes around. Regardless, it is time to break out the new ultrasonic cleaner for the first time; my plan is Simple Green XD (straight, or a solution?) and how long is a reasonable “session” in the machine for each batch (I expect to treat each component’s parts separately so I do not mix up the parts).
First up is this 1974 Falcon. There are few things about identifying the bike a bit problematic, despite it being a one-owner bike. The shop where he bought it, well, I worked there that year for about 6 months that year, and all of the Falcons sold there were built up from bare frames with components chosen by the buyer and the staff — no two alike. And, I cannot claim to have the entire line-up memorized anyway. That other Falcon I did earlier this year, also 1974 and also from a childhood friend, had a nice spec with 531 butted tubes and Campy dropouts, and no chrome at all. This one has no-name dropouts (but they look “forged” to me and have an integral RD hanger) but the fork is chromed, as are the head lugs — and nowhere else. No clue which model. And, there’s a lot to clean up, it’s been hanging in a garage a long time.
Mish-mash of components: SR cranks, Campy NR derailleurs, Suntour barcons (I think I sold them to the owner later, after I tired of them), Fiamme bars and stem, Weinmann centerpulls, Brooks Pro saddle on a straight steel post (!) The wheels are plain Normandys and 27” steel rims, he and I seem to recall he quickly decided to ditch the tubulars and these were the only wheels I had hanging around in my basement at the time.
Mostly it needs rehab, all cleaned/polished/lubed/assembled. The wheels go away, as I have a spare set of 700C alloys with Campy hubs to donate; and that gas-pipe seat post must go (my micrometer suggests 26.4mm despite being quite out-of-round, does that sound right?)
It took much of the day to break it down to the last nut-bolt-and-washer. Hey, I found I had one of those Campy pedal cap wrenches! And, oddly, the front brake had 10mm pivot bolts, and the rears were 11mm? Of course the “most fun” were getting the springs disengaged on the derailleurs and calipers, and I am sure to be cursing when the time for reassembling them comes around. Regardless, it is time to break out the new ultrasonic cleaner for the first time; my plan is Simple Green XD (straight, or a solution?) and how long is a reasonable “session” in the machine for each batch (I expect to treat each component’s parts separately so I do not mix up the parts).
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964:
#2
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,272
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
this model three-tube 531 plain gauge
expect you would discover a pillar size of either 26.2mm or 26.4mm
dropouts appear to be either Campag Sport 1010/1 or the the Agrati replica thereof
since you have satisfied yourself that they are unmarked that would indicate the Agrati version
both have the small hole to accommodate the spring of the Campag Sport model gear mech
due to lugs am thinking frame earlier than stated date
do not wish to question that it may have been purchased new in 1974 but it appears to come from a slightly earlier time
a bit odd that dropouts exhibit eyelets while fork ends do not
fork ends appear to be true forged as a raised area around track nut can be seen...or this may be just a washer...
this usually makes one suspect a fork replacement
crown appears to be Vagner model DL
Ernest could be quite eclectic when it came to selecting bits for his frame construction at any given moment in time so it is best not to place too much weight on catalogue representations...
-----
this model three-tube 531 plain gauge
expect you would discover a pillar size of either 26.2mm or 26.4mm
dropouts appear to be either Campag Sport 1010/1 or the the Agrati replica thereof
since you have satisfied yourself that they are unmarked that would indicate the Agrati version
both have the small hole to accommodate the spring of the Campag Sport model gear mech
due to lugs am thinking frame earlier than stated date
do not wish to question that it may have been purchased new in 1974 but it appears to come from a slightly earlier time
a bit odd that dropouts exhibit eyelets while fork ends do not
fork ends appear to be true forged as a raised area around track nut can be seen...or this may be just a washer...
this usually makes one suspect a fork replacement
crown appears to be Vagner model DL
Ernest could be quite eclectic when it came to selecting bits for his frame construction at any given moment in time so it is best not to place too much weight on catalogue representations...
-----
Last edited by juvela; 12-04-23 at 03:50 PM. Reason: addition
Likes For juvela:
#3
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,629
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3891 Post(s)
Liked 6,491 Times
in
3,213 Posts
For the calipers, overhaul one at a time and use a small screwdriver to pry the spring back in place. Take pics along the way if necessary.
Likes For SurferRosa:
#4
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Instead of photos, I have another bike sitting here with NR derailleurs and Weinmann brakes as a reference.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Last edited by tiger1964; 12-04-23 at 04:18 PM. Reason: .
#5
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
Falcon was a small enough mfg that buying a smattering of frame sets of varying build dates does not surprise.
looks like a reasonable bike.
review the old seat post for scraping that might indicate where tight spot(s) might be.
looks like a reasonable bike.
review the old seat post for scraping that might indicate where tight spot(s) might be.
Likes For repechage:
#6
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,272
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
forgot to mention above -
there is a good assemblage of early seventies Falcon paper here -
https://velo-pages.com/main.php?g2_itemId=26656
the nineteen seventy-four catalogue -
https://velo-pages.com/main.php?g2_itemId=27334
advisory: looking at Falcon paper can sometimes raise more questions than it solves...
Ernest also went on to fabricate cycles under his own name a few years later
-----
forgot to mention above -
there is a good assemblage of early seventies Falcon paper here -
https://velo-pages.com/main.php?g2_itemId=26656
the nineteen seventy-four catalogue -
https://velo-pages.com/main.php?g2_itemId=27334
advisory: looking at Falcon paper can sometimes raise more questions than it solves...
Ernest also went on to fabricate cycles under his own name a few years later
-----
#7
Senior Member
Join Date: Jul 2007
Location: Manhattan & Woodstock NY
Posts: 2,751
Bikes: 1987 Mercian Pro, 1985 Shogun 500, early '70s Falcon San Remo, 1972 Peugeot PX-10, 1972 Schwinn Paramount P13-9, 1971 Raleigh International, 1971 Peugeot PX-10, 1970 Raleigh Professional Mk1
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
Quoted: 939 Post(s)
Liked 2,951 Times
in
983 Posts
I went through similar machinations trying to identify the Falcon I bought a few years back. With the help of the VCC marque enthusiast (he can be found on cyclechat under the username mandobob) the closest possibility we got to is a San Remo Mk II, possibly late 60's - early 70's. The rounded seat stay treatment at the cluster and the larger seat tube diameter are clues. Mine very closely resembles this: https://velo-pages.com/main.php?g2_itemId=27461 with the exception of the chromed lugs and that seat stay treatment.
__________________
1987 Mercian Pro, 1985 Shogun 500, 197? Falcon San Remo, 1972 Peugeot PX-10, 1972 Schwinn Paramount P13-9, 1971 Peugeot PX-10, 1971 Raleigh International, 1970 Raleigh Professional Mark I
Curator/Team Mechanic: 2016 Dawes Streetfighter, 1984 Lotus Eclair, 1975 Motobecane Jubile Mixte, 1974 Raleigh Sports, 1973 Free Spirit Ted Williams, 1972 Raleigh Super Course, 1971 Philips Sport
1987 Mercian Pro, 1985 Shogun 500, 197? Falcon San Remo, 1972 Peugeot PX-10, 1972 Schwinn Paramount P13-9, 1971 Peugeot PX-10, 1971 Raleigh International, 1970 Raleigh Professional Mark I
Curator/Team Mechanic: 2016 Dawes Streetfighter, 1984 Lotus Eclair, 1975 Motobecane Jubile Mixte, 1974 Raleigh Sports, 1973 Free Spirit Ted Williams, 1972 Raleigh Super Course, 1971 Philips Sport
#8
Senior Member
Join Date: Aug 2017
Location: Minneapolis
Posts: 936
Bikes: 1968 Raleigh Super Course, 1972 Raleigh Professional, 1975 Raleigh International, 1978 Raleigh Professional, 1985 Raleigh Prestige, 1972 Schwinn Paramount, 1980 Schwinn Voyageur 11.8, 1960 Carlton Franco Suisse Peugeot PX10, 1972 Motobecane Le Champ
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 323 Post(s)
Liked 690 Times
in
351 Posts
The replacement fork looks to be the American market version of the top model San Remo 76. Most of them in the UK had the Davis style Fork Crown but the US had these. I’m looking for a fork just like it for my San Remo 76, now I’m jealous!
Last edited by Pcampeau; 12-04-23 at 10:40 PM.
#9
Standard Member
Join Date: Apr 2009
Location: Brunswick, Maine
Posts: 4,274
Bikes: 1948 P. Barnard & Son, 1962 Rudge Sports, 1963 Freddie Grubb Routier, 1980 Manufrance Hirondelle, 1983 F. Moser Sprint, 1989 Raleigh Technium Pre, 2001 Raleigh M80
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1298 Post(s)
Liked 940 Times
in
490 Posts
The bike is interesting in that it is the only non-Raleigh/Carlton that I have seen with that early-'60's design of wrap-around seat stays. The chain-rings look to have some life left in them. How does the freewheel look?
__________________
Unless you climb the rungs strategically, you’re not going to build the muscle you need to stay at the top.
Unless you climb the rungs strategically, you’re not going to build the muscle you need to stay at the top.
Likes For 1989Pre:
#10
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,272
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
me local Falcon stockist in California at this time had the model 76 exhibiting the Davis crown so perhaps both types were exported to the U.S.
variation may have been due to Don Ernesto using what he could get given the conditions of the boom (wylde speculation)
as recalled, the model 76 was only available in the team/house colour of powder blue at this epoch
can make no claim to Falcon expertise
-----
Last edited by juvela; 12-05-23 at 10:41 AM. Reason: addition
#11
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Both of the "1974" Falcons currently at my house have the wraparounds. Thanks for the input on the chainrings, I'm trying to save my friends some money. Freewheel goes in the trash.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#12
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,272
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
been meaning to inquire regarding the cycle's stem
from what can be seen in photo it appears it might be a FIAMME
be this correct? if not, does it show any markings?
thank you!
-----
been meaning to inquire regarding the cycle's stem
from what can be seen in photo it appears it might be a FIAMME
be this correct? if not, does it show any markings?
thank you!
-----
#13
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Hmm, I have no interest in, or sue for, the wheels that I am removing -- Normandy high flange hubs but 27" steel rims. I wonder if, once cleaned up, a bike co-op would find a use for them? To save a bike with damaged wheels, I guess they are better than nothing (barely!)
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#14
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Update: Photo of some components after not only cleaning, polishing and coating, but reassembly (finally!) Actually, parts from all three of the winter projects: Falcon, Legnano and Falcon (but I wasn't planning on posting the same photo three times).
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964:
#15
Senior Member
Join Date: Jun 2021
Posts: 1,683
Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 761 Post(s)
Liked 1,563 Times
in
757 Posts
#16
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,272
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
he has made mention previous of Wolfgangs
-----
he has made mention previous of Wolfgangs
-----
Likes For juvela:
#17
The Huffmeister
Join Date: Jul 2008
Location: The Le Grande HQ
Posts: 2,741
Bikes: '79 Trek 938, '86 Jim Merz Allez SE, '90 Miyata 1000, '68 PX-10, '80 PXN-10, '73 Super Course, '87 Guerciotti, '83 Trek 600, '80 Huffy Le Grande
Mentioned: 45 Post(s)
Tagged: 0 Thread(s)
Quoted: 1227 Post(s)
Liked 3,561 Times
in
1,412 Posts
w00t!
__________________
There were 135 Confentes, but only one...Huffente!
There were 135 Confentes, but only one...Huffente!
#18
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Correct. That said, I wonder if a good coat of car wax would also work well. So far on my bikes, I am pleased at how the components retain their shine over time -- but, then again, I am a fair-weather rider, no rain or mud; I would be curious what, for instance, PNW riders experience.
I finally looked up the meaning of that. Thanks.
I finally looked up the meaning of that. Thanks.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#19
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,800
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,330 Times
in
837 Posts
My 1971 American Eagle (Nishiki) Semi-Pro (Competition) had wrap-around seat stays.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#20
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
Started on reassembly of the Falcon today. First item was, of course the headset. I had previously bought a headset race press to push the races into the frame’s head tubes and, on at least one bike, it’s too short for long head tubes as those are rarely seen on modern bikes. The Falcon proved the same, so I resorted to the Old Method — a rubber mallet and patience. Not too bad. Unlike the Peugeot, this one has loose bearings instead of caged — unusual for a Campy in my experience. I had been very careful during disassembly, and had 23 for the top and 23 for the bottom and once in fresh grease, it seemed like a lot of space left over. I did research online plus my 1974 Sutherland’s shop manual, and it says 3/16” bearings on Campy, and 20 to 22 balls. Also, the by-eye method is jam is as many as will fit, then remove two so the headset will not bind up while turning. So I needed a couple more and I fortunately have bags of each possible size. Checking with my micrometer, the bearings are… 5/32"? Huh? That’s common on non-Campy but the races clearly say Campagnolo, so this must be some version one normally does not see. Regardless, in place now and smooth as silk; final adjustment can wait until towards the end of the project, and I included the brake cable hanger in the “stack” anyway.
Bars and stem were next, and on all three bikes I am setting the stem at the maximum marked “safe” height, just to make the bikes easier to ride. Brake levers went on, they are the tiniest bit bent left/right, but I suspect not enough to notice upon casual inspection, or while riding.
To install the bar tape — wait a minute! Glad I remembered…. This bike has handlebar-end shifters! So, those are in place, and that meant the upper sections of cable housing and it helps to install the housing stop on the downtube to help hold it all there. Now the tape is on, again over the Fizik brand gel pads. The combination of the thick cushion tape and the gel pads makes the bar look a bit “fat” but I’ll bet the reduction in shock to the arms will pay off while riding. And the bar end shifters feel a bit gritty in actuation; I just now got some guidance from the forum, and feel confident I can slide the ratchet mechanisms out and clean/lube them, hopefully that helps.
The wheels need to come back off briefly, as I forgot to polish up the hubs and spoke for additional sparkle. Also, on both the Falcon and the Peugeot at this point, I am going to apply the “ceramic coating”, basically a wax but better, that I started using on both cars and the gloss is great with that stuff and should help protect the bike. I think so far, it looks pretty good. The tire “look right” — there is room that I possibly could have installed fatter 30mm ones (available in black only ☹️) but that’s probably not a lot of difference in ride, and might have looked odd.
Bars and stem were next, and on all three bikes I am setting the stem at the maximum marked “safe” height, just to make the bikes easier to ride. Brake levers went on, they are the tiniest bit bent left/right, but I suspect not enough to notice upon casual inspection, or while riding.
To install the bar tape — wait a minute! Glad I remembered…. This bike has handlebar-end shifters! So, those are in place, and that meant the upper sections of cable housing and it helps to install the housing stop on the downtube to help hold it all there. Now the tape is on, again over the Fizik brand gel pads. The combination of the thick cushion tape and the gel pads makes the bar look a bit “fat” but I’ll bet the reduction in shock to the arms will pay off while riding. And the bar end shifters feel a bit gritty in actuation; I just now got some guidance from the forum, and feel confident I can slide the ratchet mechanisms out and clean/lube them, hopefully that helps.
The wheels need to come back off briefly, as I forgot to polish up the hubs and spoke for additional sparkle. Also, on both the Falcon and the Peugeot at this point, I am going to apply the “ceramic coating”, basically a wax but better, that I started using on both cars and the gloss is great with that stuff and should help protect the bike. I think so far, it looks pretty good. The tire “look right” — there is room that I possibly could have installed fatter 30mm ones (available in black only ☹️) but that’s probably not a lot of difference in ride, and might have looked odd.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#21
Senior Member
Thread Starter
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 642 Times
in
407 Posts
OK, the bike is “assembled” now, really only still needing a water bottle and cage; that said, I need to go over the bike 100% (and then some) making sure every bolt is tight and correctly adjusted. In particular, the headset is just finger tight. After that, it needs at least two shakedown rides with tightness checks in between.
Sadly, the batteries in my household scale have died, so I cannot give even a ballpark weight. Nice enough components but it is straight-gauge tubing, and a 25” frame as well. Probably approaching 25 pounds? Then again, that might be pessimistic.
A couple of things:
(a) No surprise but going from 27” wheels to 700C means brake reach is affected and even in the bottom position, not QUITE enough reach. Therefore, a little grinding of the caliper is in order; sure, it would stop right now, but how many stops until tire blows? And there are tire savers installed and getting the brake perfectly centered and tight while preventing the tire savers from doing Rock Around the Clock is not easy — at least on the rear; on the front the center bolt was long enough for two NyLock nuts (M6 x1mm, by the way, cheap from Amazon in stainless in packs), one of which holds the brake and the second for the tire saver.
(b) First time dealing with barcons in so many decades. After the rebuild the SunTour shifters seem to work really well — but the cable routing strikes me as really inelegant, I have a clip holding the cables together below the handlebars, and I still need a zip-tie directly above the housing stop on the downtube to keep the cables from drooping. Moreover, the shift cable housing comes rather close to the front brake’s straddle cable assembly. Is there a fix?
(c) there is also a zip tie on the chain stay just aft of the housing stop for the rear derailleur. The ‘modern’ housing is a bit stiffer than I am used to and wants to exit the stop at an angle. I am hoping it settles into its new shape and the zip tie becomes superfluous. Or — last year member “oneclick” made up some special ferrules that fit my Raleigh project perfectly for this exact reason, I think I still have one or more in my “cables and small parts” box.
Sadly, the batteries in my household scale have died, so I cannot give even a ballpark weight. Nice enough components but it is straight-gauge tubing, and a 25” frame as well. Probably approaching 25 pounds? Then again, that might be pessimistic.
A couple of things:
(a) No surprise but going from 27” wheels to 700C means brake reach is affected and even in the bottom position, not QUITE enough reach. Therefore, a little grinding of the caliper is in order; sure, it would stop right now, but how many stops until tire blows? And there are tire savers installed and getting the brake perfectly centered and tight while preventing the tire savers from doing Rock Around the Clock is not easy — at least on the rear; on the front the center bolt was long enough for two NyLock nuts (M6 x1mm, by the way, cheap from Amazon in stainless in packs), one of which holds the brake and the second for the tire saver.
(b) First time dealing with barcons in so many decades. After the rebuild the SunTour shifters seem to work really well — but the cable routing strikes me as really inelegant, I have a clip holding the cables together below the handlebars, and I still need a zip-tie directly above the housing stop on the downtube to keep the cables from drooping. Moreover, the shift cable housing comes rather close to the front brake’s straddle cable assembly. Is there a fix?
(c) there is also a zip tie on the chain stay just aft of the housing stop for the rear derailleur. The ‘modern’ housing is a bit stiffer than I am used to and wants to exit the stop at an angle. I am hoping it settles into its new shape and the zip tie becomes superfluous. Or — last year member “oneclick” made up some special ferrules that fit my Raleigh project perfectly for this exact reason, I think I still have one or more in my “cables and small parts” box.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964: