What is this part called?
#1
Senior Member
Thread Starter
What is this part called?
I need help identifying a tiny part on my bike as it has fallen off so I need to replace it. It's a tiny nipple that is crimped on to the bare ends of the gear cables.
What is that blue part called?
What is that blue part called?
#2
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4340 Post(s)
Liked 2,985 Times
in
1,621 Posts
It's called a cable crimp, or end cap.
Last edited by DiabloScott; 07-14-18 at 02:12 PM.
#3
Senior Member
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,083
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3382 Post(s)
Liked 5,547 Times
in
2,878 Posts
I don't even use those.
I just use an inch or two of heatshrink tubing on the ends of cables.
I just use an inch or two of heatshrink tubing on the ends of cables.
#4
like we used to say
#5
Senior Member
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,083
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3382 Post(s)
Liked 5,547 Times
in
2,878 Posts
#7
Senior Member
Those are the widgets that were always used as examples in business school.
#8
like we used to say
#10
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,434
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 3,003 Times
in
1,930 Posts
#15
Senior Member
Cheez! The local bike shop will probably give you a handful of cable crimps for a quarter. Why all this extra work with solder, glue, etc.?
#16
Banned
I do that to the cable, before I cut it.. it's a bit tricky with stainless steel cables..
plain Zn Treated steel easier .. then I pull it back out and coat the wire with grease..
before calling it done..
Soldered end makes pulling regreasing and putting it back in.
for maintenance.. easier, also ..
...
#17
Senior Member
It's a cheap blend if it doesn't stick OR it hasn't been degreased/fluxed. It isn't worth going through that kind of trouble, tbh. In almost any case where removing the cable end would be necessary, you might as well replace the cable if it's too short to re-clamp.
#18
Senior Member
Join Date: Apr 2011
Posts: 7,161
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4466 Post(s)
Liked 1,602 Times
in
1,054 Posts
And when you need to pull the cables, the ends aren't all bent up.
#19
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,434
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 3,003 Times
in
1,930 Posts
While I do agree, it does serve more then just for being repurposed. Preventing the fray lessens the likelihood it'll prick the fingers/leg should it come unwantedly contacted with or to address an adjustment.
__________________
-Oh Hey!
-Oh Hey!
Thread
Thread Starter
Forum
Replies
Last Post
loimpact
Bicycle Mechanics
2
08-04-19 06:11 AM
fxdgrjedi
Cyclocross and Gravelbiking (Recreational)
4
12-20-14 12:42 PM