Tubeless tires - overnight pressure loss question
#1
Senior Member
Thread Starter
Tubeless tires - overnight pressure loss question
I just mounted three sets of tubeless tires on three separate wheel sets. Added 2oz of sealant per wheel to the 700x28C tires and about 3oz of sealant to the 700x32C tires.
On all three sets one of the two tires was pretty much flat the next morning. Added a little more sealant to each tire that had lost most of it's pressure, pumped each back up to about 90 PSI, bounced the tire off the ground a few times, spun it, etc... Rode one of the wheel sets about 25 miles but couldn't ride all three...
I know going flat overnight isn't acceptable but what is the approximate amount of air loss in a tubeless setup overnight? I checked the set I'd ridden and they were down about 3PSI the next day.
Thanks.
On all three sets one of the two tires was pretty much flat the next morning. Added a little more sealant to each tire that had lost most of it's pressure, pumped each back up to about 90 PSI, bounced the tire off the ground a few times, spun it, etc... Rode one of the wheel sets about 25 miles but couldn't ride all three...
I know going flat overnight isn't acceptable but what is the approximate amount of air loss in a tubeless setup overnight? I checked the set I'd ridden and they were down about 3PSI the next day.
Thanks.
#2
Senior Member
I find some air loss is common after first setting up, but it dissipates after a ride or two as the sealant has an opportunity through riding to distribute.I wouldn’t worry about three pounds, you may have lost that much just via the act of using a pressure gauge.
But if you are going completely flat, something isn’t right. Two common causes of a failure to seal are taping issues and valve stem not being fully seated. Make sure the tape you are using is wide enough to fully seal spoke holes (assumingyour rim has holes) — it should be wide enough to cover from bead channel to bead channel. For the stem, when installing, press hard from inside of the rim while tightening the valve nut with fingers. Some wheels require more effort to get the valve to fully seat than others.
But if you are going completely flat, something isn’t right. Two common causes of a failure to seal are taping issues and valve stem not being fully seated. Make sure the tape you are using is wide enough to fully seal spoke holes (assumingyour rim has holes) — it should be wide enough to cover from bead channel to bead channel. For the stem, when installing, press hard from inside of the rim while tightening the valve nut with fingers. Some wheels require more effort to get the valve to fully seat than others.
Last edited by DOS; 05-19-20 at 09:14 PM.
#3
Full Member
I've had these issues before (and right now with a rear wheel on my gravel bike) and it's usually been the result of the tire not completely seating on the rim. The fix that's worked for me has been to put a tube in before setting up tubeless, go for a ride (or two), then pull out the tube. You have to carefully remove the tube, trying to maintain one side of the rim-tire setup, but this works pretty well. I guess I was feeling cocky (lazy?) with my gravel bike recently, but I have to go back and run it with a tube.
#4
Non omnino gravis
#5
Senior Member
Join Date: Oct 2009
Location: Further North than U
Posts: 2,000
Bikes: Spec Roubaix, three Fisher Montare, two Pugs
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 39 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Slosh it
I just mounted three sets of tubeless tires on three separate wheel sets. Added 2oz of sealant per wheel to the 700x28C tires and about 3oz of sealant to the 700x32C tires.
On all three sets one of the two tires was pretty much flat the next morning. Added a little more sealant to each tire that had lost most of it's pressure, pumped each back up to about 90 PSI, bounced the tire off the ground a few times, spun it, etc... Rode one of the wheel sets about 25 miles but couldn't ride all three...
I know going flat overnight isn't acceptable but what is the approximate amount of air loss in a tubeless setup overnight? I checked the set I'd ridden and they were down about 3PSI the next day.
Thanks.
On all three sets one of the two tires was pretty much flat the next morning. Added a little more sealant to each tire that had lost most of it's pressure, pumped each back up to about 90 PSI, bounced the tire off the ground a few times, spun it, etc... Rode one of the wheel sets about 25 miles but couldn't ride all three...
I know going flat overnight isn't acceptable but what is the approximate amount of air loss in a tubeless setup overnight? I checked the set I'd ridden and they were down about 3PSI the next day.
Thanks.