Filetreads ARE faster!
#1
Senior Member
Thread Starter
Filetreads ARE faster!
It seems obvious but I've tried mine a few times on my yard course and didn't really know how much faster they were.
It seems like I have to pump them up a few PSI firmer than my knobby tires of same diameter.
It's been dry so far this season so I'm being tempted more and more to race my filetreads. I tried them most seriously today so far. They definitely slipped and slided and washed out in the corners more. My course is dry and pretty firm but does have some loamy/leafy corners. Crashed out once.
I tried a few moderate laps on my moderate-knob FMB + Cane Creek sweet wheelset and came in a consistent 3min25sec per lap.
Then I did a few laps on my Challenge filetreads on ancient Yellow Label 36spoke wheels and the laps all clocked in at 3:15.
I could vary my perceived effort and my lap times still came in with those differences. Seems like a noticeable difference! ...But I did have to ride smoother and pay more attention in the corners. And I wasn't really pushing it. At race pace I'm guessing I'd have to take it noticeably easier in tricky corners if there was any looseness to them. But it seems like they do still go faster.
They were fun and I like a skill challenge to try to figure out.
It seems like I have to pump them up a few PSI firmer than my knobby tires of same diameter.
It's been dry so far this season so I'm being tempted more and more to race my filetreads. I tried them most seriously today so far. They definitely slipped and slided and washed out in the corners more. My course is dry and pretty firm but does have some loamy/leafy corners. Crashed out once.
I tried a few moderate laps on my moderate-knob FMB + Cane Creek sweet wheelset and came in a consistent 3min25sec per lap.
Then I did a few laps on my Challenge filetreads on ancient Yellow Label 36spoke wheels and the laps all clocked in at 3:15.
I could vary my perceived effort and my lap times still came in with those differences. Seems like a noticeable difference! ...But I did have to ride smoother and pay more attention in the corners. And I wasn't really pushing it. At race pace I'm guessing I'd have to take it noticeably easier in tricky corners if there was any looseness to them. But it seems like they do still go faster.
They were fun and I like a skill challenge to try to figure out.
#2
Senior Member
While not the most scientific test situation, nice try testing out the different tires! Working up the skill in the corners can only help in the long run. I've been told a few times if you aren't falling you aren't trying hard enough.
That said, I don't think I'd race on file treads on any course that wasn't all grass. Any dirt corners and I'd want more knobs. Especially in racing conditions where 15 seconds does not really matter when all you have to do is beat the guy in front of you.
Add in the risk and extra effort to avoid washing out in a corner? No thanks. Gotta finish the race to win it.
That said, I don't think I'd race on file treads on any course that wasn't all grass. Any dirt corners and I'd want more knobs. Especially in racing conditions where 15 seconds does not really matter when all you have to do is beat the guy in front of you.
Add in the risk and extra effort to avoid washing out in a corner? No thanks. Gotta finish the race to win it.
#3
Senior Member
Thread Starter
I'm confused. 15 secs would let me beat the guy ahead of me.
Anyway, I just messed up my theory. I'd been doing repeatable 3:25 w knobs, 3:15 filetread. Today I did 3:10 with both filetread and knobs. So much for that! Of course I was sliding a bit w both. The knobs were clearly easier in corners but the filetreads felt predictable even if slippy. I like a slippy feeling OK. I'm into skiing so I don't mind cultivating this angle. The filetreads did FEEL faster, like they wind up nice. I like them. If it's dry, I'll for sure do test laps of any event with them! I'll bring various wheels then race what feels best!
Anyway, I just messed up my theory. I'd been doing repeatable 3:25 w knobs, 3:15 filetread. Today I did 3:10 with both filetread and knobs. So much for that! Of course I was sliding a bit w both. The knobs were clearly easier in corners but the filetreads felt predictable even if slippy. I like a slippy feeling OK. I'm into skiing so I don't mind cultivating this angle. The filetreads did FEEL faster, like they wind up nice. I like them. If it's dry, I'll for sure do test laps of any event with them! I'll bring various wheels then race what feels best!
#4
Senior Member
Sure it would. In a TT. But you're just talking about practicing in your own course; 15 seconds in practice seems negligible in the real world condition of a race.
Exactly. This is what I meant about beating the guy in front of you. Timing laps in practice seems like a good idea to build up fitness and work toward beating your previous goal, but not that important since it is so dependent on the individual session. I'd be more worried about power output, heart rate or staying upright in practice and finding out what actually works on race day.
I can get behind this.
I can get behind this.
#7
Senior Member
No tread is faster
The linked blog post is about winning a 'cross race with 54mm road tires.
https://janheine.wordpress.com/2017/...tage-in-cross/
https://janheine.wordpress.com/2017/...tage-in-cross/
#8
Senior Member
Join Date: Sep 2011
Posts: 4,764
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1975 Post(s)
Liked 232 Times
in
173 Posts
The linked blog post is about winning a 'cross race with 54mm road tires.
https://janheine.wordpress.com/2017/...tage-in-cross/
https://janheine.wordpress.com/2017/...tage-in-cross/
#9
Senior Member
Thread Starter
Ha. Definitely use a tire for its purpose. Dry hardpack with grass.
I raced yesterday damp grass hardpack. In the morning I used intermediate knobs and had 6:45 laps. In the afternoon the course held totally the same. I guess worn in a bit thought. I used filetreads and had 6:15 laps. Others had faster laps, too. But I finished way higher against way better racers. They're definitely LIGHTER and sure felt zippier.
I raced yesterday damp grass hardpack. In the morning I used intermediate knobs and had 6:45 laps. In the afternoon the course held totally the same. I guess worn in a bit thought. I used filetreads and had 6:15 laps. Others had faster laps, too. But I finished way higher against way better racers. They're definitely LIGHTER and sure felt zippier.
#10
Tiocfáidh ár Lá
A file tread tire like the Speed Max has knobs on the sides for cornering so they are actually quite good in the corners. I love file treads and use them probably more then any other tire for the races in the south east which are typically dry.
#11
Senior Member
While not the most scientific test situation, nice try testing out the different tires! Working up the skill in the corners can only help in the long run. I've been told a few times if you aren't falling you aren't trying hard enough.
That said, I don't think I'd race on file treads on any course that wasn't all grass. Any dirt corners and I'd want more knobs. Especially in racing conditions where 15 seconds does not really matter when all you have to do is beat the guy in front of you.
Add in the risk and extra effort to avoid washing out in a corner? No thanks. Gotta finish the race to win it.
That said, I don't think I'd race on file treads on any course that wasn't all grass. Any dirt corners and I'd want more knobs. Especially in racing conditions where 15 seconds does not really matter when all you have to do is beat the guy in front of you.
Add in the risk and extra effort to avoid washing out in a corner? No thanks. Gotta finish the race to win it.
Filetreads work if you are really used to them on an ideal course, but one slip or crash could eliminate all the benefit. I think for most of us, the risk isn't worth it. I always play it conservative and go a touch more aggressive just to have a higher factor of safety in corners.
There are fast local guys that race on mud tires year around and still place well.
My least aggressive tire is Ritchey Shield, works well enough on 90% of dry courses.
With that said it's fun to experiment, not to take anything away from you OP. Have at it....
#12
Senior Member
Join Date: Jul 2010
Location: Michigan
Posts: 4,863
Bikes: too many of all kinds
Mentioned: 35 Post(s)
Tagged: 0 Thread(s)
Quoted: 1147 Post(s)
Liked 415 Times
in
335 Posts
The linked blog post is about winning a 'cross race with 54mm road tires.
https://janheine.wordpress.com/2017/...tage-in-cross/
https://janheine.wordpress.com/2017/...tage-in-cross/
yeah, I took my 60mm slicks mountain biking and obviouslyl they wer a total nightmare if the terrain was just a little bit damp. Forget damp grass or mud.
Interestingly they didn't do great on sandy turns either.
Jan is big on the "tredless thing" and Honest I lean that way too.
What he consistantly misses is that treaded tires slide well. Slicks go down fast and hard. Could he have saved is crash if he had knobs? I know I have been in situations where knobs made all the difference. I even ran knobs on the front and slicks on the back - the rear end obviously gave way in hard turns where sliding was involved.
Fattish tires on straight sand is an unfair advantage. Fattish tires work well if they have the traction (dry course or sand)
He makes a big point of why they sell few treaded tires. Yeah, if you are gravel riding and not going fast enough to get a little sideways they are great (in the dry).
For gravel (non competitive), Personally I run 90% slicks in the summer. In the winter I have tread because I want to be able to catch my bike when it starts to go sideways.
I think a big part of his advantage was flotation in the straight sand sections. The weight disadvantage for me would be significant somewhere around 40mm+
#13
Senior Member
Join Date: Sep 2011
Posts: 4,764
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1975 Post(s)
Liked 232 Times
in
173 Posts
Interesting read, thanks.
yeah, I took my 60mm slicks mountain biking and obviouslyl they wer a total nightmare if the terrain was just a little bit damp. Forget damp grass or mud.
Interestingly they didn't do great on sandy turns either.
Jan is big on the "tredless thing" and Honest I lean that way too.
What he consistantly misses is that treaded tires slide well. Slicks go down fast and hard. Could he have saved is crash if he had knobs? I know I have been in situations where knobs made all the difference. I even ran knobs on the front and slicks on the back - the rear end obviously gave way in hard turns where sliding was involved.
Fattish tires on straight sand is an unfair advantage. Fattish tires work well if they have the traction (dry course or sand)
He makes a big point of why they sell few treaded tires. Yeah, if you are gravel riding and not going fast enough to get a little sideways they are great (in the dry).
For gravel (non competitive), Personally I run 90% slicks in the summer. In the winter I have tread because I want to be able to catch my bike when it starts to go sideways.
I think a big part of his advantage was flotation in the straight sand sections. The weight disadvantage for me would be significant somewhere around 40mm+
yeah, I took my 60mm slicks mountain biking and obviouslyl they wer a total nightmare if the terrain was just a little bit damp. Forget damp grass or mud.
Interestingly they didn't do great on sandy turns either.
Jan is big on the "tredless thing" and Honest I lean that way too.
What he consistantly misses is that treaded tires slide well. Slicks go down fast and hard. Could he have saved is crash if he had knobs? I know I have been in situations where knobs made all the difference. I even ran knobs on the front and slicks on the back - the rear end obviously gave way in hard turns where sliding was involved.
Fattish tires on straight sand is an unfair advantage. Fattish tires work well if they have the traction (dry course or sand)
He makes a big point of why they sell few treaded tires. Yeah, if you are gravel riding and not going fast enough to get a little sideways they are great (in the dry).
For gravel (non competitive), Personally I run 90% slicks in the summer. In the winter I have tread because I want to be able to catch my bike when it starts to go sideways.
I think a big part of his advantage was flotation in the straight sand sections. The weight disadvantage for me would be significant somewhere around 40mm+
#15
Senior Member
Join Date: May 2015
Posts: 84
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It makes me sad to see he couldnt ride that bike with fat tires in that sand. I agree with redlube, definetley a case of sandbagging.
#17
Senior Member
#21
Senior Member
Thread Starter
Now, now... all these posts about Jan are LAME on the face of them. So knock it off. Or start your own jealous wannabe thread.
He's lucky he got to do a race! We have no idea how well he did or if he had a good time at his latest sufferfest. All I know is that I finally get to do one this weekend -- it's been weeks. I'm in withdrawal.
...And if it's not wet it's GONNA BE FILETREADS coz they're faster and awesome! I'd much rather try to use more skill in the corners and enjoy all that free speed and lightness. Actually, I notice that the only extra skill I've had to use has -- like all skill -- been enjoyable. I do try to corner more smoothly. Heck, I was also having issues w my intermediates when I wasn't paying attn while cornering. Also, I enjoy some sliding, but I find when I pay attn that I don't. Sniff.
He's lucky he got to do a race! We have no idea how well he did or if he had a good time at his latest sufferfest. All I know is that I finally get to do one this weekend -- it's been weeks. I'm in withdrawal.
...And if it's not wet it's GONNA BE FILETREADS coz they're faster and awesome! I'd much rather try to use more skill in the corners and enjoy all that free speed and lightness. Actually, I notice that the only extra skill I've had to use has -- like all skill -- been enjoyable. I do try to corner more smoothly. Heck, I was also having issues w my intermediates when I wasn't paying attn while cornering. Also, I enjoy some sliding, but I find when I pay attn that I don't. Sniff.
#22
Senior Member
Join Date: Aug 2014
Location: PNW
Posts: 197
Bikes: Cutthroat, Scalpel, Roubaix, Sequoia, SuperX, Diverge
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 51 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I did that race with my Salsa Cutthroat, 2.3" Renegade MTB tires which blow up almost to 2.4" on the i30 Roval Traverse wheels.
Couldn't make it through the 2 sand sections because they turned. Moment there was a turn, all advantage was lost. The disadvantage around every turn due to the extra weight greatly reduced any minor advantage in that short, 10-15ft straight sand pit that pretty much everybody could blow through
Couldn't make it through the 2 sand sections because they turned. Moment there was a turn, all advantage was lost. The disadvantage around every turn due to the extra weight greatly reduced any minor advantage in that short, 10-15ft straight sand pit that pretty much everybody could blow through
#23
Senior Member
The problem with a 2" tire on super-loose sand is that it can be too floaty to slice through the surface, but not floaty enough to float. Then it just sort of wallows, aimlessly and sluggishly. I use that tire on my gravel bike, it's blazing fast on anything that doesn't break up very badly beneath it, but there's not really any way to get it to behave well on mud or bad sand... it wouldn't really surprise me if it was a significant overall advantage on that particular course.