Stripped hex bolt of my SPD, anyway to change the bolt out?
#2
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,601
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 427 Post(s)
Liked 700 Times
in
436 Posts
You could expoxy a hex wrench in there. And unless it's a very long hex wrench than you can cut some off of, use a "sacrificial wrench". Of course, be certain not to get expoxy where you don't want it! Could also see if a torx wrench might have enough "grab: to turn it out.
#3
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
A very common 1st attempt is to hammer in a slightly oversized Torx bit.
I’ve had good luck welding a nut onto stripped screws, but the size and depth of recess makes that a less than ideal option here. Drilling the head off should work a treat, but only If you also can remove that part later to get to the shank of the screw to remove the rest later.
I’ve had good luck welding a nut onto stripped screws, but the size and depth of recess makes that a less than ideal option here. Drilling the head off should work a treat, but only If you also can remove that part later to get to the shank of the screw to remove the rest later.
Likes For dabac:
#4
Senior Member
Can't help with how to replace it, but keeping all the pivet points clean and lubed on these pedals will help them last and last, and help avoid the stiffness that may have caused this happening.
Once in a while I use a rag and screwdriver to clean out debris and lube. Chain oil, wd40, it all works. Wd40 is good because the spray gets into crevices and can flush stuff out.
I'm always amazed how my early 90s shimano spd's still function.
Good luck. I rarely adjust the tension, prefer the lower setting anyway, so after cleaning well to reduce friction, you might get away with one of the techniques mentioned and then just leave it.
Is it tensioned too tight or too loose? If too tight, a general good clean and lube may all that is needed.
Once in a while I use a rag and screwdriver to clean out debris and lube. Chain oil, wd40, it all works. Wd40 is good because the spray gets into crevices and can flush stuff out.
I'm always amazed how my early 90s shimano spd's still function.
Good luck. I rarely adjust the tension, prefer the lower setting anyway, so after cleaning well to reduce friction, you might get away with one of the techniques mentioned and then just leave it.
Is it tensioned too tight or too loose? If too tight, a general good clean and lube may all that is needed.
Likes For djb:
#5
Senior Member
Join Date: Jan 2013
Posts: 2,681
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 584 Times
in
410 Posts
I would first try a torx, then epoxy in a hex, and if that somehow did not work then an Easy Out screw extractor.
#6
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,516
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,401 Times
in
2,058 Posts
#7
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,810 Times
in
3,318 Posts
What's stripped, the threads or the hex socket?
If the socket, then are you trying to use a ANSI size hex key that almost fits in a metric socket? Use the correct metric size.
If the threads, then you do realize that is a captive bolt and that it will not come out of that hole. So maybe not stripped. But if it is stripped, you are going to have to remove the top plate. Then take a small screwdriver or something and wedge underneath the opposite end of the screw while you turn the screw with the hex key.
But you are unlikely to find a proper replacement for that screw unless you have other of the same pedals that are scrapped.
If the socket, then are you trying to use a ANSI size hex key that almost fits in a metric socket? Use the correct metric size.
If the threads, then you do realize that is a captive bolt and that it will not come out of that hole. So maybe not stripped. But if it is stripped, you are going to have to remove the top plate. Then take a small screwdriver or something and wedge underneath the opposite end of the screw while you turn the screw with the hex key.
But you are unlikely to find a proper replacement for that screw unless you have other of the same pedals that are scrapped.