History of Dura Ace
#26
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,180
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1561 Post(s)
Liked 1,284 Times
in
855 Posts
Not saying that other gruppos on other bikes can't be similarly improved, but there are many setup details that can make a NR gruppo work far better than it typically did back in the day.
A lot of this has to do with choice of chain and freewheel, with possible axle position consideration and/or B-tension mods to match (especially if the freewheel is smallish).
Then there is the cable's run, with modern lined derailer housing and plastic noodle at the bottom bracket area (I use only silicone/Teflon lubricants on the cable)
Lastly the shift lever should be lubricated internally, and then kept adjusted to move as freely as permissible.
Sedisport chain is a good choice because it is stiffer than modern chain while still narrow enough for 7s cog spacing.
9s chain can also work well on the right freewheel or cassette, it's thinner so less likely to want to overshift onto bigger sprockets than wanted.
A lot of this has to do with choice of chain and freewheel, with possible axle position consideration and/or B-tension mods to match (especially if the freewheel is smallish).
Then there is the cable's run, with modern lined derailer housing and plastic noodle at the bottom bracket area (I use only silicone/Teflon lubricants on the cable)
Lastly the shift lever should be lubricated internally, and then kept adjusted to move as freely as permissible.
Sedisport chain is a good choice because it is stiffer than modern chain while still narrow enough for 7s cog spacing.
9s chain can also work well on the right freewheel or cassette, it's thinner so less likely to want to overshift onto bigger sprockets than wanted.
#27
Senior Member
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,082
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1440 Post(s)
Liked 1,383 Times
in
757 Posts
I had first gen Dura-Ace on my Volare. I needed new rear cones. I found something almost identical, but it didn't deal properly against the dust cap, so they tend to leak grease. When you look at the two tires of cones it's clear there is a subtle difference. It's not just a matter of slightly different tolerances.
#28
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,001
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4334 Post(s)
Liked 2,977 Times
in
1,614 Posts
Well that's a bit of an exaggeration. But yes, all of us had to get over the concept that bike parts should be maintainable and rebuildable and last forever.
#29
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,146
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2361 Post(s)
Liked 1,745 Times
in
1,189 Posts
Until this video, I had no idea I was mispronouncing Shee-mano.
#30
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1607 Post(s)
Liked 2,213 Times
in
1,103 Posts
I really liked the 740x parts on the Pinarello. DT 8V levers and all. Very nice. What is not nice is not being able to replace a worn rear hub cone. Not any easier than finding the same for a Helicomatic hub! That and my bias from my early 20;s, in converting the bike to Campagnolo 8V
DA is a product unto itself, then there is the ret of Shimano products.
Recently rebuilt a pair of 10V Ergo's from 1997. Same parts as Chorus for economy of scale in production. Try doing that with DA STI's!
DA is a product unto itself, then there is the ret of Shimano products.
Recently rebuilt a pair of 10V Ergo's from 1997. Same parts as Chorus for economy of scale in production. Try doing that with DA STI's!
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#31
Senior Member
I had original Crane derailleurs in long and short cage versions, original Dura Ace brakes, Dura Ace hubs, all kinds of stuff. There is nothing wrong with any of it, In fact, it was all quite good.
After a decade of various "upgrades", I went back to Nuovo Record and remain there to this day.
#32
Senior Member
Join Date: Oct 2017
Posts: 2,040
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 837 Post(s)
Liked 1,080 Times
in
521 Posts
How were you pronouncing it? “Shuh-mano”? If so that’s close and probably how the majority use it in english.
Its ok, we don’t say ramen, tsunami, sayonara or Honda correctly either.
Its ok, we don’t say ramen, tsunami, sayonara or Honda correctly either.
Last edited by polymorphself; 09-25-20 at 10:58 PM.
#33
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,146
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2361 Post(s)
Liked 1,745 Times
in
1,189 Posts
#35
Senior Member
Join Date: Nov 2004
Posts: 23,223
Mentioned: 654 Post(s)
Tagged: 1 Thread(s)
Quoted: 4722 Post(s)
Likes: 0
Liked 3,036 Times
in
1,874 Posts
Likes For T-Mar:
#36
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,001
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4334 Post(s)
Liked 2,977 Times
in
1,614 Posts
At least it's better than the current logo and trend for Campagnolo's top group which is a combination of upper and lower case letters. To be correct, I should type it as rECOrD or rEcorD (I'm not sure if the 'C' and 'O' are upper or lower case). By 2050 they'll probably be using some backwards and/or upside down letters!
Likes For DiabloScott:
#37
Bike Butcher of Portland
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,630
Bikes: It's complicated.
Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4677 Post(s)
Liked 5,790 Times
in
2,279 Posts
#38
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,146
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2361 Post(s)
Liked 1,745 Times
in
1,189 Posts
At least it's better than the current logo and trend for Campagnolo's top group which is a combination of upper and lower case letters. To be correct, I should type it as rECOrD or rEcorD (I'm not sure if the 'C' and 'O' are upper or lower case). By 2050 they'll probably be using some backwards and/or upside down letters!
#39
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,029
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4507 Post(s)
Liked 6,373 Times
in
3,665 Posts
#40
Me duelen las nalgas
Join Date: Aug 2015
Location: Texas
Posts: 13,513
Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel
Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4559 Post(s)
Liked 2,802 Times
in
1,800 Posts
Dura Ace will eventually pull a SyFy and rename itself DURACE. Decades from now users will argue over whether it's pronounced "do race."
#41
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,146
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2361 Post(s)
Liked 1,745 Times
in
1,189 Posts
Likes For madpogue:
#42
Senior Member
Join Date: Nov 2004
Posts: 23,223
Mentioned: 654 Post(s)
Tagged: 1 Thread(s)
Quoted: 4722 Post(s)
Likes: 0
Liked 3,036 Times
in
1,874 Posts
Based on preponderance of spellings and pronunciation, that Italian company's name should have been changed to Campagnola, or maybe even Campy/Campi/Campee, at least as far back as the early 1970s. Of course, in the Commonwealth, it would have been Campag.
#44
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,146
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2361 Post(s)
Liked 1,745 Times
in
1,189 Posts
The poor folks at Schwinn would have to change their name on a weekly basis.