Normandy Hub Service Help
#1
Junior Member
Thread Starter
Join Date: May 2013
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Normandy Hub Service Help
Hi,
I am trying to service the Normandy front hub on my Raleigh Grand Sport but when I tried to undo the lock nuts on the axle it gets more difficult to turn when it reaches the end of the axle. The axle itself has a slot cut into it and appears to flare to a larger diameter towards the end. I am assuming to retain the nuts so they don't easily come off.
I am hesitant to use force to get the nuts off the axle since I'm not sure if I can damage them or maybe won't be able to easily put them back on. Does anyone have any experience with these Normandy hubs?
Also what size balls should I replace the old ones with? The axle doesn't turn all that smoothly and has a slight play i them.
PS. I was trying to upload some photos but can't do so because I need at least 10 posts here.
Thanks in advance!
- Daniel
I am trying to service the Normandy front hub on my Raleigh Grand Sport but when I tried to undo the lock nuts on the axle it gets more difficult to turn when it reaches the end of the axle. The axle itself has a slot cut into it and appears to flare to a larger diameter towards the end. I am assuming to retain the nuts so they don't easily come off.
I am hesitant to use force to get the nuts off the axle since I'm not sure if I can damage them or maybe won't be able to easily put them back on. Does anyone have any experience with these Normandy hubs?
Also what size balls should I replace the old ones with? The axle doesn't turn all that smoothly and has a slight play i them.
PS. I was trying to upload some photos but can't do so because I need at least 10 posts here.
Thanks in advance!
- Daniel
#2
Senior Member
Join Date: Jul 2014
Location: Central Indiana
Posts: 2,159
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 913 Post(s)
Liked 515 Times
in
344 Posts
Welcome to bikeforums, Daniel.
Your threads are buggered all right.
I would not try to crank the locknuts off. Some judicious filing and using a sacrificial axle nut or chasing die of the appropriate size might salvage the nuts & cones. The axle probably be replaced.
Your threads are buggered all right.
I would not try to crank the locknuts off. Some judicious filing and using a sacrificial axle nut or chasing die of the appropriate size might salvage the nuts & cones. The axle probably be replaced.
#3
Senior Member
Join Date: Jul 2014
Location: Central Indiana
Posts: 2,159
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 913 Post(s)
Liked 515 Times
in
344 Posts
You need to determine what damaged the axle and address that. As far as bearing size, my memory is not what it used to be so I shouldn't guess but someone will be along that knows that. I would have to check tonight.
#4
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,626
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3888 Post(s)
Liked 6,485 Times
in
3,209 Posts
I've done this a thousand times and always used the force of two wrenches to remove the nut. You may need to lock two nuts (cone and locknut) on the other side to apply your second wrench to a fixed spot.
Once you remove the locknuts and clean everything thoroughly, use the same nuts (or different ones of the same threading) to fix the threading of the axle by threading the nut on and off multiple times. This has always worked for me.
Don't overthink it.
Once you remove the locknuts and clean everything thoroughly, use the same nuts (or different ones of the same threading) to fix the threading of the axle by threading the nut on and off multiple times. This has always worked for me.
Don't overthink it.
#5
Member
Agreed, counter lock the cone and nut on the opposite side and go back and forth with the offending nut using wd40 as a lubricant/cutting oil, unless its really screwed up works every time, a brass brushing of the offending threads also helps, they might just be crudded up.
#6
Senior Member
Hi,
I am trying to service the Normandy front hub on my Raleigh Grand Sport but when I tried to undo the lock nuts on the axle it gets more difficult to turn when it reaches the end of the axle. The axle itself has a slot cut into it and appears to flare to a larger diameter towards the end. I am assuming to retain the nuts so they don't easily come off.
I am hesitant to use force to get the nuts off the axle since I'm not sure if I can damage them or maybe won't be able to easily put them back on. Does anyone have any experience with these Normandy hubs?
Also what size balls should I replace the old ones with? The axle doesn't turn all that smoothly and has a slight play i them.
I am trying to service the Normandy front hub on my Raleigh Grand Sport but when I tried to undo the lock nuts on the axle it gets more difficult to turn when it reaches the end of the axle. The axle itself has a slot cut into it and appears to flare to a larger diameter towards the end. I am assuming to retain the nuts so they don't easily come off.
I am hesitant to use force to get the nuts off the axle since I'm not sure if I can damage them or maybe won't be able to easily put them back on. Does anyone have any experience with these Normandy hubs?
Also what size balls should I replace the old ones with? The axle doesn't turn all that smoothly and has a slight play i them.
I would also suggest using lots of lube and trying to force the locknut past the distortion. You can file the end slightly if there's a burr or something. It the axle is too mangled for this, you could run a die on the threads to clean them up. Should be 9x1mm
Keep in mind you only need to undo the lock nut and cone on one side. So pick the one with the least obvious damage.
I've rebuilt a lot of Normandy hubs (BITD). They are super normal in every way. Can't recall the ball size offhand. 3/16" I think but double check.
#7
Senior Member
Join Date: May 2013
Location: Greenwood SC USA
Posts: 2,252
Bikes: 2002 Mercian Vincitore, 1982 Mercian Colorado, 1976 Puch Royal X, 1973 Raleigh Competition, 1971 Gitane Tour de France and others
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 1,395 Times
in
694 Posts
FWIW, the basic classic Normandy Sport, when cleaned and repacked with good bearings and good grease, can be a remarkably smooth running hub. I think they're worth the bother.
I wish there were readily available replacement cones for the fancier Normandy Luxe Competition, though I will note that the nasty pitted ones in my Puch's wheels still run shockingly smoothly.
I wish there were readily available replacement cones for the fancier Normandy Luxe Competition, though I will note that the nasty pitted ones in my Puch's wheels still run shockingly smoothly.
#8
Used to be Conspiratemus
Join Date: Jan 2009
Location: Hamilton ON Canada
Posts: 1,512
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 297 Post(s)
Liked 245 Times
in
163 Posts
3/16" balls for a Normandy front. This is fresh in my memory because I bought one, laced into an MA-2 rim for like 20 bucks about 2 years ago, and took it apart to re-grease it.
Unless the ends of the axle are grossly deformed with chunks out of the threads, much worse than yours appear to be, twisting the locknut off through them with oil or some such should clean them up. Even Campagnolo locknuts resist a little. The hard part is immobilizing the axle so it doesn't turn. Cinch the locknut gently to the cone at the other end of the axle and then hold the far-side cone with a cone wrench. (That way, when you twist the nut counter-clockwise, the far-side cone wants to drive into the far-side locknut, stabilizing it. If you hold the far-side locknut, it will tend to back away from the cone (unless it's cinched tight), de-stabilizing it. For the far side, you're looking at the "back of the clock", right?) The slot in the axle is nice here because if there is old grease and dirt in the threads, the slot will work like the flute of a thread tap to evacuate the crud as you turn the nut...and that may be all you need.
Hint: check the other end of the axle. If the locknut comes off that side easier, just retighten the "bad" side and leave it alone. Remove the nut and cone from the "good" side in this and all future overhauls. Unless the cone on the "fixed" side needs to be replaced, or the axle itself (assuming you can even find replacements), you only need to remove the parts on one end of the axle.
Unless the ends of the axle are grossly deformed with chunks out of the threads, much worse than yours appear to be, twisting the locknut off through them with oil or some such should clean them up. Even Campagnolo locknuts resist a little. The hard part is immobilizing the axle so it doesn't turn. Cinch the locknut gently to the cone at the other end of the axle and then hold the far-side cone with a cone wrench. (That way, when you twist the nut counter-clockwise, the far-side cone wants to drive into the far-side locknut, stabilizing it. If you hold the far-side locknut, it will tend to back away from the cone (unless it's cinched tight), de-stabilizing it. For the far side, you're looking at the "back of the clock", right?) The slot in the axle is nice here because if there is old grease and dirt in the threads, the slot will work like the flute of a thread tap to evacuate the crud as you turn the nut...and that may be all you need.
Hint: check the other end of the axle. If the locknut comes off that side easier, just retighten the "bad" side and leave it alone. Remove the nut and cone from the "good" side in this and all future overhauls. Unless the cone on the "fixed" side needs to be replaced, or the axle itself (assuming you can even find replacements), you only need to remove the parts on one end of the axle.
#9
Senior Member
Join Date: Sep 2015
Location: Left Coast, Canada
Posts: 5,126
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 2236 Post(s)
Liked 1,314 Times
in
707 Posts
Also, wait to see what the bearings look like after a little bath in wd40.
Sometimes old dried grease makes them feel rough but they turn out to be in good shape.
Sometimes old dried grease makes them feel rough but they turn out to be in good shape.
#10
Junior Member
Thread Starter
Join Date: May 2013
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thank you everyone for the helpful responses. I totally didn't think of the idea I only have to take off one end to get the hub apart even though I overhauled vintage hubs before =) However this is happening on both ends. Upon really close look it appears the ends of the axle were somehow crushed towards each other so where the threads starts is pushed against the next loop of threads. That's why the nuts hit almost a hard stop at the very tip of the axle when I try to remove them.
Would it be safe to just force the nut off? Assuming the hardness of the nut is higher than that of the threads on the axle? Or should I use a die to fix this?
Would it be safe to just force the nut off? Assuming the hardness of the nut is higher than that of the threads on the axle? Or should I use a die to fix this?
#11
PM me your cotters
Join Date: Jun 2015
Location: ATL
Posts: 3,241
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1137 Post(s)
Liked 590 Times
in
422 Posts
Other than forcing it off and have the nut re-chase the threads, not sure what else to do. Trying to use a die to cut new threads with the nut on there still is far too precarious.
If worst comes to worse, no doubt you can find someone here with a replacement hollow axle. I may actually have one, I donated a new shell to someone here on BF a couple years ago, I think I still have the internals (assuming it wasn't solid axle).
Don't forget: Save your self a lot of pain only unlocking nuts from one side to repack, don't touch the other side. Then there's no second-guessing and adjusting both sides later.
If worst comes to worse, no doubt you can find someone here with a replacement hollow axle. I may actually have one, I donated a new shell to someone here on BF a couple years ago, I think I still have the internals (assuming it wasn't solid axle).
Don't forget: Save your self a lot of pain only unlocking nuts from one side to repack, don't touch the other side. Then there's no second-guessing and adjusting both sides later.
#12
Senior Member
The lock nut should be harder than the axle. I can't see enough detail to gauge the problem. Might be safe, might not be safe. If you feel like you are going to damage the nuts and cones, you can always hack off the ends of the axle, remove the cones etc, and put them on a new axle.
Last edited by Salamandrine; 10-01-19 at 02:29 PM.
#13
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,786
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3588 Post(s)
Liked 3,400 Times
in
1,934 Posts
Yes, the threads look buggered on the axle. A thread file might be able to clean them up. Otherwise, those were common hubs on bike-boom era bikes and replacement axles shouldn't be too hard to find.
Also what size balls should I replace the old ones with?
#15
I never finish anyth
Join Date: Jul 2010
Location: Western KY
Posts: 1,114
Bikes: 2008 Merckx LXM, 2003 Giant XTC mtb, 2001 Lemond Alpe d'Huez, 1997 Lemond Zurich, 1989 Cannondale ST, 1988 Masi Nuovo Strada, 1983 Pinarello Turismo
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 294 Post(s)
Liked 137 Times
in
86 Posts
I would replace the axle. Should be easy to find a replacement of the proper length and likely less than $10. A lot less if you have a local bike co-op. And if you agree about the replacement, just use a grinder or file and form a conical shape on the end of the axle, removing the damaged threads as you make the conical shape.
This way you shouldn't have to force the locknut or the cone off the damaged axle. You may have to do this on both sides, but you'll be saving the cones and locknuts for use on the new axle.
The damaged axle is going to be more trouble than it's worth in the long run - clean, repack the bearings, insert the new axle, adjust the preload, and move on.
This way you shouldn't have to force the locknut or the cone off the damaged axle. You may have to do this on both sides, but you'll be saving the cones and locknuts for use on the new axle.
The damaged axle is going to be more trouble than it's worth in the long run - clean, repack the bearings, insert the new axle, adjust the preload, and move on.
__________________
Dale, NL4T
Dale, NL4T
#16
Used to be Conspiratemus
Join Date: Jan 2009
Location: Hamilton ON Canada
Posts: 1,512
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 297 Post(s)
Liked 245 Times
in
163 Posts
...Upon really close look it appears the ends of the axle were somehow crushed towards each other so where the threads starts is pushed against the next loop of threads. That's why the nuts hit almost a hard stop at the very tip of the axle when I try to remove them....
#17
Senior Member
I can't see clearly from the small pictures, but it looks like it could simply be a burr from cutting the existing axle to length. No need for sharp threads all the way to the edge.
But, the slot on that axle looks larger than it should be, though it's been decades since I've rebuilt a Normandy hub. I'm thinking this might be some cheap repurposed axle salvaged from an MTB or something. The non cheapskate solution would be a new axle.
Last edited by Salamandrine; 10-02-19 at 11:59 AM.
#18
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,043
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4512 Post(s)
Liked 6,382 Times
in
3,669 Posts
Thank you everyone for the helpful responses. I totally didn't think of the idea I only have to take off one end to get the hub apart even though I overhauled vintage hubs before =) However this is happening on both ends. Upon really close look it appears the ends of the axle were somehow crushed towards each other so where the threads starts is pushed against the next loop of threads. That's why the nuts hit almost a hard stop at the very tip of the axle when I try to remove them.
Would it be safe to just force the nut off? Assuming the hardness of the nut is higher than that of the threads on the axle? Or should I use a die to fix this?
Would it be safe to just force the nut off? Assuming the hardness of the nut is higher than that of the threads on the axle? Or should I use a die to fix this?
A wire wheel can be carefully used to smooth out the threads some, then anti seize for lube doing 1 step forward, 2 steps back turns with the nut can restore the threads if you are diligent, too much force will ruin the nut, go slow and work through it.
A die can work, often they are too sharp and if it doesn't follow the original threads can wipe out too much material. You need a chaser/rethreader and it has to be the correct thread. I make my own for odd ball bike threads and have a couple of big sets for common threads.
Last edited by merziac; 10-02-19 at 12:40 PM.
#19
Junior Member
Thread Starter
Join Date: May 2013
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Hit my 5 post limit yesterday. Gonna try to post the close up photos again. I ordered a thread file and going to try that route first.
#20
Member
You should be able to work your way right through that with the back and forth method described in numerous posts above, don't over think this, if your really worried about the Neanderthal approach, clean up the burr with the file before you start with the nut and lube solution.
#21
Senior Member
Join Date: May 2013
Location: Greenwood SC USA
Posts: 2,252
Bikes: 2002 Mercian Vincitore, 1982 Mercian Colorado, 1976 Puch Royal X, 1973 Raleigh Competition, 1971 Gitane Tour de France and others
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 1,395 Times
in
694 Posts
After seeing the pix, I am curious - is this mangled axle end perhaps an artifact of running a quick release skewer on those thin, thin, stamped dropouts Raleigh used on the Gran Sport? My memory is that I had trouble running a conventional Normandy rear hub with skewer on an ancient Raleigh Lenton when I was trying to run it as a fixed-gear - the amount of axle sticking out past the locknuts was just a whisker too much, and it required using derailleur mounting claws on the dropouts to get the skewer to clamp properly. Is that possibly what caused this problem?
#22
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,154
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2363 Post(s)
Liked 1,749 Times
in
1,191 Posts
^^^^ To the issue @rustystrings61 describes above, I noticed the same on an old Grand Prix with stamped dropouts with no derailleur hanger. Dropouts were thin, but there's the extra thickness of the RD claw on the drive side. So I "offset" the cones/locknuts so that there's more axle sticking out on the drive side.
#23
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,626
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3888 Post(s)
Liked 6,485 Times
in
3,209 Posts
I've been down this path more than a few times, and it's often as much trouble finding a replacement. A new one would cost me at least $18. Then I'd have to hacksaw it. One found at a co-op would cost me an hour or more of hunting and frustration ... and it still may not work. This is why I always try to correct the problem with the current one. Unless it's not long enough after correcting the issue, it's less trouble to merely fix the threads.
#24
Senior Member
Join Date: Nov 2014
Location: Eastern Iowa
Posts: 631
Bikes: 2014 Trek Allant drop bar conversion, modified Schwinn MTN commuter, 2015 Trek 520, Soma ES, Salsa Journeyman, 1980 Trek 414
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 178 Post(s)
Liked 355 Times
in
166 Posts
I would simply remove the boogered up thread ends either with a flat bastard file, or maybe even carefully on a belt sander. Once you remove the damaged last thread, you should be in business....doesnt look like you need that much axle sticking out anyway.
#25
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,435
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 984 Post(s)
Liked 634 Times
in
404 Posts
+1, I think I have the same set as you -- alas, cannot remember where I bought it (Northern Tool? Harbor Freight?) Did not realize for years the difference between "thread chasers" and "tap and die".
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.