Tire (not rim) has a hop
#1
Senior Member
Thread Starter
Join Date: Apr 2005
Location: Minneapolis, MN, USA
Posts: 1,152
Bikes: 1990 Burley Bossa Nova, 1992 Paramount PDG-70, 1993 Specialized Stumpjumper, 2005 Jamis Dakar XC Pro, 2007 Rivendell Bleriot
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 28 Post(s)
Likes: 0
Liked 5 Times
in
3 Posts
Tire (not rim) has a hop
maybe i'm over-sensitive to this because i've been eying my newly built wheels for wobble, but i've noticed that my tires both have a 1.5mm hop in them. They are relatively cheap but tough IRC Metro kevlar belted tires with wire beads. There is a spot on each tire that rises about 1.5mm higher than the rest of the tire.. it looks like the rim has a major hop, but the rim is true.
Is this normal? The tires are almost new, and a checked to make sure they were mounted properly.
Is this normal? The tires are almost new, and a checked to make sure they were mounted properly.
#2
Senior Member
Tube's probably pinched between the tyre and rim. Let out all most of the pressure and pull the tyre sideways so you can see down the inside edge of the time. Work your way around the entire circumference and check for the tube being caught. Pushing up on the valve-stem before inflating helps as well.
#3
Senior Member
Thread Starter
Join Date: Apr 2005
Location: Minneapolis, MN, USA
Posts: 1,152
Bikes: 1990 Burley Bossa Nova, 1992 Paramount PDG-70, 1993 Specialized Stumpjumper, 2005 Jamis Dakar XC Pro, 2007 Rivendell Bleriot
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 28 Post(s)
Likes: 0
Liked 5 Times
in
3 Posts
^^ As i said, i checked that and it was fine. The tires are also at at least 65psi, so if the tube _was_ pinched, something dramatic would probably have happened...
#5
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Does the high spot happen to be opposite the valve stem? If so, that's common. Try this:
1. Let most of the air out of the tire.
2. Push the valve stem in toward the hub.
3. Reinflate the tire.
Sometimes the tire beads get pushed up by the thick part of the tube adjacent to the valve stem. When that happens, the nice round tire is pushed so that it isn't concentric with the rim. The high spot will be exactly opposite the valve stem.
1. Let most of the air out of the tire.
2. Push the valve stem in toward the hub.
3. Reinflate the tire.
Sometimes the tire beads get pushed up by the thick part of the tube adjacent to the valve stem. When that happens, the nice round tire is pushed so that it isn't concentric with the rim. The high spot will be exactly opposite the valve stem.
#6
60mph in the 42 ring!
Join Date: Jul 2003
Location: Niagara Frontier, NY
Posts: 546
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I think you should either stop measuring your tires with a micrometer and just ride the blasted thing, or else go out and buy better tires.
#7
Senior Member
Thread Starter
Join Date: Apr 2005
Location: Minneapolis, MN, USA
Posts: 1,152
Bikes: 1990 Burley Bossa Nova, 1992 Paramount PDG-70, 1993 Specialized Stumpjumper, 2005 Jamis Dakar XC Pro, 2007 Rivendell Bleriot
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 28 Post(s)
Likes: 0
Liked 5 Times
in
3 Posts
Originally Posted by Dave Stohler
I think you should either stop measuring your tires with a micrometer and just ride the blasted thing, or else go out and buy better tires.
Heh.. probably good advice.
#8
Senior Member
Thread Starter
Join Date: Apr 2005
Location: Minneapolis, MN, USA
Posts: 1,152
Bikes: 1990 Burley Bossa Nova, 1992 Paramount PDG-70, 1993 Specialized Stumpjumper, 2005 Jamis Dakar XC Pro, 2007 Rivendell Bleriot
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 28 Post(s)
Likes: 0
Liked 5 Times
in
3 Posts
Originally Posted by Retro Grouch
Does the high spot happen to be opposite the valve stem? If so, that's common. Try this:
1. Let most of the air out of the tire.
2. Push the valve stem in toward the hub.
3. Reinflate the tire.
Sometimes the tire beads get pushed up by the thick part of the tube adjacent to the valve stem. When that happens, the nice round tire is pushed so that it isn't concentric with the rim. The high spot will be exactly opposite the valve stem.
1. Let most of the air out of the tire.
2. Push the valve stem in toward the hub.
3. Reinflate the tire.
Sometimes the tire beads get pushed up by the thick part of the tube adjacent to the valve stem. When that happens, the nice round tire is pushed so that it isn't concentric with the rim. The high spot will be exactly opposite the valve stem.
#9
Junk Collector
Join Date: Jun 2005
Location: Chicago IL
Posts: 973
Bikes: 1987 Schwinn Circuit, 2012 Colnago M10, 1990 Schwinn CrissCross
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 34 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Originally Posted by robo
maybe i'm over-sensitive to this because i've been eying my newly built wheels for wobble, but i've noticed that my tires both have a 1.5mm hop in them. They are relatively cheap but tough IRC Metro kevlar belted tires with wire beads. There is a spot on each tire that rises about 1.5mm higher than the rest of the tire.. it looks like the rim has a major hop, but the rim is true.
Is this normal? The tires are almost new, and a checked to make sure they were mounted properly.
Is this normal? The tires are almost new, and a checked to make sure they were mounted properly.