25 mm diameter seatpost
#1
Senior Member
Thread Starter
Join Date: Jul 2016
Posts: 111
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 55 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
25 mm diameter seatpost
I am having a difficult time finding a 25 mm diameter aluminum seat post for my Look KG281.
The Look original carbon seat post is old and starting slipping due to a poor 2 piece wedge shaped clamp.
I have tried anti slipping carbon paste but it still twists and moves vertically under force.
I am hoping an aluminum post will not be as smooth as the wedge clamps are very much so.
Thanks in advance..
The Look original carbon seat post is old and starting slipping due to a poor 2 piece wedge shaped clamp.
I have tried anti slipping carbon paste but it still twists and moves vertically under force.
I am hoping an aluminum post will not be as smooth as the wedge clamps are very much so.
Thanks in advance..
#3
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
However, below that listing is a 25mm American Classic post for $54 - I had a couple of these BITD - reasonably light, good two-screw angle setting and robust. I ultimately replaced them with a Chorus Ti post and an otherwise-identical Daytona steel post, but that was because I was on a bling quest, not that there was anything wrong with the AC posts. My only concern is that the one listed might not be long enough for a sloping TT frame (couldn't see length listed).
But i do think that eBay is the OPs best friend here - barring obvious trauma, there's not much that can go wrong with an Al seat post.
Last edited by Litespud; 09-11-20 at 11:52 AM.
#4
I’m a little Surly
Join Date: Jan 2010
Location: Near the district
Posts: 2,422
Bikes: Two Cross Checks, a Karate Monkey, a Disc Trucker, and a VO Randonneur
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 699 Post(s)
Liked 1,294 Times
in
647 Posts
three hundred for a seat post?
However, below that listing is a 25mm American Classic post for $54 - I had a couple of these BITD - reasonably light, good two-screw angle setting and robust. I ultimately replaced them with a Chorus Ti post and an otherwise-identical Daytona steel post, but that was because I was on a bling quest, not that there was anything wrong with the AC posts. My only concern is that the one listed might not be long enough for a sloping TT frame (couldn't see length listed).
But i do think that eBay is the OPs best friend here - barring obvious trauma, there's not much that can go wrong with an Al seat post.
However, below that listing is a 25mm American Classic post for $54 - I had a couple of these BITD - reasonably light, good two-screw angle setting and robust. I ultimately replaced them with a Chorus Ti post and an otherwise-identical Daytona steel post, but that was because I was on a bling quest, not that there was anything wrong with the AC posts. My only concern is that the one listed might not be long enough for a sloping TT frame (couldn't see length listed).
But i do think that eBay is the OPs best friend here - barring obvious trauma, there's not much that can go wrong with an Al seat post.
25's were never (drives cost) all that common (Frenchism) if you have a bike that needs one and you want to keep it I'd get a couple of them.
#5
Senior Member
Thread Starter
Join Date: Jul 2016
Posts: 111
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 55 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
25mm diameter seat post
I am having a difficult time finding a 25 mm diameter aluminum seat post for my Look KG281.
The Look original carbon seat post is old and starting slipping due to a poor 2 piece wedge shaped clamp.
I have tried anti slipping carbon paste but it still twists and moves vertically under force.
I am hoping an aluminum post will not be as smooth as the wedge clamps are very much so.
Thanks in advance..
The Look original carbon seat post is old and starting slipping due to a poor 2 piece wedge shaped clamp.
I have tried anti slipping carbon paste but it still twists and moves vertically under force.
I am hoping an aluminum post will not be as smooth as the wedge clamps are very much so.
Thanks in advance..
#6
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 7,662
Bikes: Miyata 618 GT, Marinoni, Kestral 200 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 1610 Post(s)
Liked 2,592 Times
in
1,224 Posts
#7
Banned
I got Campagnolo 25.0 seat posts from the same importer I got my AlAn screwed & glued frame & fork, that used them , in the 80's
Kalloy makes low cost seatposts from 25.0 mm & larger in 0.2 mm increments in aluminum ,
their finish is not highly polished which, in this situation may be an advantage..
Kalloy makes low cost seatposts from 25.0 mm & larger in 0.2 mm increments in aluminum ,
their finish is not highly polished which, in this situation may be an advantage..
#8
Banned
Moderator merge these 2 identical threads?
#9
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,399
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,699 Times
in
2,519 Posts
If you think a moderator should do something, there is a report button at the bottom of every post.
Merged two threads
Merged two threads
#11
Senior Member
Join Date: Sep 2009
Location: Up
Posts: 4,695
Bikes: Masi, Giant TCR, Eisentraut (retired), Jamis Aurora Elite, Zullo, Cannondale, 84 & 93 Stumpjumpers, Waterford, Tern D8, Bianchi, Gunner Roadie, Serotta, Serotta Duette, was gifted a Diamond Back
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 305 Post(s)
Liked 2,038 Times
in
604 Posts
No, at the bottom of your signature section there is a large round button with a red dot and ! in it. Hover over that and it says "report post"