What to do with a cracked rear dropout?
12-02-11, 10:28 PM
#1
Senior Member
Thread Starter
Join Date: Aug 2010
Posts: 228
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What to do with a cracked rear dropout?
Tried to have this rear right dropout squeezed back after it was spread by the derailleur catching in the spokes. Needless to say, the shop tried and the dropout cracked as you can see near the adjusters.
I had a local framebuilder quote me on these options:
1. Have him tig-weld the dropout after finishing squeezing it together. $40
2. Have him tig-weld the dropout and then retap the dropout so the adjuster can function again: $80
3. If I provide the dropout, replaced the rear dropout with a new one: $150
does this seem reasonable? I'm inclined towards option 1 or 2. It's a nice frame, a 1975 Bob Jackson, but I don't have the time or money right now to do a full replacement.
Pictures:
I had a local framebuilder quote me on these options:
1. Have him tig-weld the dropout after finishing squeezing it together. $40
2. Have him tig-weld the dropout and then retap the dropout so the adjuster can function again: $80
3. If I provide the dropout, replaced the rear dropout with a new one: $150
does this seem reasonable? I'm inclined towards option 1 or 2. It's a nice frame, a 1975 Bob Jackson, but I don't have the time or money right now to do a full replacement.
Pictures:
12-02-11, 10:44 PM
#2
is just a real cool dude
Join Date: Aug 2010
Location: The Thumb, MI
Posts: 3,165
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 32 Post(s)
Likes: 0
Liked 34 Times
in
14 Posts
Do you really need the adjusters? The left one looks pretty roached out so I would just remove both and have drive side TIG welded to completely fill the adjuster hole. Then just retap it or leave it filled up as it would be a little bit stronger.
12-02-11, 11:04 PM
#3
Senior Member
Thread Starter
Join Date: Aug 2010
Posts: 228
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I suppose I don't. I was thinking of making this bike a single speed conversion anyways with a nice tall stem and moustache handlebars.
12-03-11, 09:32 AM
#4
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,402
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,701 Times
in
2,521 Posts
those are very reasonable prices. Unless it's a very special bike, I probably would just go with the minimum.
12-12-11, 07:44 PM
#5
Senior Member
Join Date: Apr 2011
Location: Lancaster,CA the desert north of Los Angeles
Posts: 701
Bikes: 84' Ciocc, 79' Shogun 1000, 76' KHS Gran Sport, 96' Schwinn Super Sport,
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Have it TIG welded, and you can buy the drill and tap cheap whenever you want.
Thread
Thread Starter
Forum
Replies
Last Post
simonaway427
Cyclocross and Gravelbiking (Recreational)
2
08-21-11 07:20 PM
