New SPD cleats stick
#1
Senior Member
Thread Starter
New SPD cleats stick
My wife got a new pair of shoes yesterday and when we went out today she could barely get her shoe out of the pedal. She could unclip by turning her heel into the bike but would have to really jam it outwards to break loose. I took a close look at the new cleats with the old ones next to them and noticed that the inside shoulder on the side that engages the front of the pedal clip appeared to have a slight bulge compared to the cleat on her old shoe. I swapped the cleats out and problem solved. I have never run into this before. If we were just starting out with clipless I don't know if we would have solved it. We would probably just think clipping out is hard. I guess a bike store tech might have seen the problem right away but it was not obvious unless you compared the old and new cleats next to each other.
#2
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,627
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3870 Post(s)
Liked 2,563 Times
in
1,577 Posts
There are a couple different kinds of cleats -- shoes often come with the easy-release type (SH56), but the ones sold separately are generally the single-direction ones that hold better (SH51)
#3
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
@ThermionicScott is right.
There are two different cleats - SH56 "Multi Release" and SH51 "Single Release." Single release are for aggressive riding and racing. Multi release are for casual riding and touring.
See https://forum.cyclinguk.org/viewtopi...=94258#p868063 for a very good explanation and photos of the differences.
There are two different cleats - SH56 "Multi Release" and SH51 "Single Release." Single release are for aggressive riding and racing. Multi release are for casual riding and touring.
See https://forum.cyclinguk.org/viewtopi...=94258#p868063 for a very good explanation and photos of the differences.
#4
Senior Member
Thread Starter
Thanks for the info re 56 v 51. The old ones were 56 and the new 51. But something else was wrong since the 51s jammed in the direction shown and released in the inward direction (on the right side only; thne left side was OK). The cleats were not upside down although that would be a humorous cause.
i think we will just stick with the old cleats for now on my wife's shoes. I don’t even know what I have on mine. The number is worn off from walking around. Time for me to get new ones I guess.
i think we will just stick with the old cleats for now on my wife's shoes. I don’t even know what I have on mine. The number is worn off from walking around. Time for me to get new ones I guess.
Last edited by donheff; 05-25-18 at 05:51 AM.
#5
Senior Member
In addition to the difference in the Shimano cleats, there are cleats from other manufacturers that are similar to Shimano but are just a little different, such as Welgo. Some of the cleat\pedal combs work fine, others not so much.
And what I usually do for folks new with clipless is to set the release tension to the minimum, it can be increased later if desired. But not one ever asks for that to happen. I do it on my own bikes, and almost never increase it.
And what I usually do for folks new with clipless is to set the release tension to the minimum, it can be increased later if desired. But not one ever asks for that to happen. I do it on my own bikes, and almost never increase it.
#6
Newbie
Join Date: May 2017
Location: Texas
Posts: 74
Bikes: Spec Roubaix, Trek Superfly
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Liked 0 Times
in
0 Posts
Agree with above. While not as much of a fix, try a bit of WD-40 or chain lube on the pedals.