Tire overall diameter vs width
#1
Junior Member
Thread Starter
Join Date: Mar 2010
Posts: 22
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 15 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
Tire overall diameter vs width
Lets say a 700x28c tire has 6mm clearance between seatstays and chainstays, but only 4mm clearance to the seattube. If one chooses a 32c tire, that should add 2mm to each side, still giving 4mm clearance. But, does the overall diameter increase by 4mm, or is it more like half just like each side so increase by 2mm? Would it theoretically touch the seattube?
Thanks.
Thanks.
#2
Senior Member
Join Date: Oct 2006
Location: Orange County, CA
Posts: 4,770
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 630 Post(s)
Likes: 0
Liked 369 Times
in
206 Posts
There is no definite answer as it depends on the tire, rim, and air pressure. But here's a general rule of thumb:
https://www.bikecalc.com/wheel_size_math
Based on that, 700x28 is 678mm diameter, 700x32 is 786mm diameter. The increase is 8mm diameter or 4mm radius so it will be very tight
https://www.bikecalc.com/wheel_size_math
Based on that, 700x28 is 678mm diameter, 700x32 is 786mm diameter. The increase is 8mm diameter or 4mm radius so it will be very tight
#3
Senior Member
Join Date: Mar 2010
Location: Seattle, WA
Posts: 23,208
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 18883 Post(s)
Liked 10,646 Times
in
6,054 Posts
You won't really know for sure until you try it. Some tires measure big for their size, some small, and then the rims you put them on have a big effect too.
#4
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
Over all diameter increases by 8mm. But different makes and models of tire YMMV. It's just an estimate. You do only get roughly 4mm closer to the seat post, brake caliper or whatever is of the most concern on your bike.
The formula to estimate tire diameter is Wheel diameter = rim bsd + tire width * 2
The formula to estimate tire diameter is Wheel diameter = rim bsd + tire width * 2
#5
just another gosling
Join Date: Feb 2007
Location: Everett, WA
Posts: 19,531
Bikes: CoMo Speedster 2003, Trek 5200, CAAD 9, Fred 2004
Mentioned: 115 Post(s)
Tagged: 0 Thread(s)
Quoted: 3886 Post(s)
Liked 1,938 Times
in
1,383 Posts
Only way to tell is to borrow or buy a candidate tire. Issue with really tight to the fork is that bits of gravel etc. picked up by the tire will scar the fork's crown. No big deal if alu, but not so good if carbon. Seen that happen.
__________________
Results matter
Results matter
#6
Senior Member
Join Date: Jan 2010
Location: TC, MN
Posts: 39,520
Bikes: R3 Disc, Haanjo
Mentioned: 354 Post(s)
Tagged: 1 Thread(s)
Quoted: 20810 Post(s)
Liked 9,456 Times
in
4,672 Posts
Your direct question has been answered, so to chip in I'll add this: when most manufacturers specify that a frame will clear a certain tire size, it's typically with ~4mm clearance on all sides - that's generally the minimum that they want for clearing debris and whatnot. With that in mind, you may want to ask yourself why manufacturers want that clearance and whether or not you're comfortable going with a thinner margin for error.
#7
Senior Member
If your clearance is tight, you might find it gets tighter as your tire gets older and thinner as the tire will balloon out as it gets more flexible.
#9
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
(the wheelset has an inner width of 15mm)
Last edited by Iride01; 07-24-19 at 07:35 PM.
#10
Senior Member
Join Date: Apr 2011
Location: Alpharetta, GA
Posts: 15,280
Bikes: Nashbar Road
Mentioned: 71 Post(s)
Tagged: 0 Thread(s)
Quoted: 2934 Post(s)
Liked 341 Times
in
228 Posts