Anyone use their C&V on a trainer? & what to do about surface rust?
#1
Junior Member
Thread Starter
Join Date: Apr 2016
Location: Dallas
Posts: 132
Bikes: Current Stable: 1973 Mercian Vincitore;1985 CIOCC Designer'84;1988 Raleigh "531c USA" ;1990 LeMond Maillot Jaune Z Team; 1991 Fuji Titanium;1996 Calfee LunaPro-Lemond Z team Tribute Replica; 2013 Wilier Zero.Seven
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 47 Post(s)
Liked 31 Times
in
14 Posts
Anyone use their C&V on a trainer? & what to do about surface rust?
Curious is anyone is mounting and using their bike(s) on a trainer? I had my Mercian on a smart trainer for a while and apparently I wasn't too good at wiping the sweat off afterwards and now have some surface rust spots. Sooo, part two of the question what's the best way to deal with surface rust?
#2
Senior Member
Join Date: Oct 2012
Location: Twin Cities, Minnesota, USA
Posts: 1,257
Bikes: 2017 Salsa Carbon Mukluk frame built with XT, 2018 Kona Rove NRB build with Sram Apex 1,2008 Salsa El Mariachi, 1986 Centurion Ironman
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 286 Post(s)
Liked 100 Times
in
65 Posts
I bought an '85 Centurion Ironman for the trainer
It's been working great. I use a RockBros sweat net to keep sweat off the top tube, and I have a hand towel over the front wheel to keep it off the wheel and fork. Both work great. The Ironman, in near showroom condition, cost $85, the trainer, an excellent condition 1-Up, was $40. Picked up a couple Conti trainer tires for $10/each.
#3
Senior Member
Wahoo has yet to release a freewheel adapter for the Kickr so I'm stuck using my modern bikes on the trainer, but sweat is sweat and bad for any bike. I have an air mover in front of me and a smaller fan behind the trainer aimed at my lower back, a sweat catcher on the bike, and I wear a base layer, sweat band, and fingerless gloves to help manage the sweat that does form.
Likes For phenry24:
#4
Full Member
Join Date: Apr 2019
Location: Northern NJ
Posts: 419
Bikes: 1987 Pinarello Montello, 1996 Litespeed Classic, 1996 Colnago Master Light, 1997 Litespeed Ultimate, 2006 Opera Leonardo FP, 2006 Pinarello Paris FP, 1984 Pinarello Record, 89-ish Cornelo Profilo
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 119 Times
in
73 Posts
I use a sweatguard on my trainer bike but still get some corrosion here and there. Simple solution is dont use a good bike - I can count on one hand the number of times any of my road bikes (ie bikes I use on the road) have been on the trainer. I have a cheap Fuji Roubaix dedicated to the purpose. When it decays, I'll replace it with something else cheap.
Likes For CyclingFool95:
#5
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,613
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10956 Post(s)
Liked 7,486 Times
in
4,187 Posts
Bike thong.
Towel that covers bars/wheel/fork.
Fan.
Towel that covers bars/wheel/fork.
Fan.
#6
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,833
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 604 Post(s)
Liked 1,063 Times
in
535 Posts
No brainer, you should have used water pipe insulation on top tube, no sweat issues. At this point I would just spray some LPS 3 on the rust, then get some pipe insulation.
Tim
Last edited by tkamd73; 10-06-19 at 08:37 PM.
Likes For tkamd73:
#7
Banned.
Join Date: Dec 2007
Posts: 27,199
Mentioned: 34 Post(s)
Tagged: 1 Thread(s)
Quoted: 378 Post(s)
Liked 1,409 Times
in
909 Posts
I had a Schwinn Magnadyne and it rusted out. Must have been the wet clothes I hung on it.
I quit using a trainer because I can't hang as many clothes on it as an exercise bike or treadmill.
@speedevil gave me one of those things you use to protect the bike from sweat. I have it on my spin bike.
I quit using a trainer because I can't hang as many clothes on it as an exercise bike or treadmill.
@speedevil gave me one of those things you use to protect the bike from sweat. I have it on my spin bike.
#8
Senior Member
Join Date: Nov 2013
Location: Near Pottstown, PA: 30 miles NW of Philadelphia
Posts: 2,186
Bikes: 2 Trek Mtn, Cannondale R600 road, 6 vintage road bikes
Mentioned: 83 Post(s)
Tagged: 0 Thread(s)
Quoted: 472 Post(s)
Liked 1,028 Times
in
404 Posts
I have my poor old Motobecane Mirage clamped into the mag stationary trainer. Pitiful old bicycle. I modified the mag adjuster to boost the drag so it works well but.....its in my unheated garage and I only use it in winter. Garages here in Pennsylvania can get pretty cold. I do have a terry towel rigged over the TT and cockpit but I don't sweat much. I generally start with 4 layers of clothes, gloves and knit hat. Over time I shed most of the layers but barely sweat and just mop my forehead a bit.
The rig sits in front of a window, looking at the horse pasture. I grind away to tunes on the stereo, watching the horses. They watch me too, probably thinking "WTF is that idiot doing? Works real hard, goes nowhere, don't look happy and they call us dumb animals". I keep the Moto's stem shifters up against 'the fire wall' in top gear and just turn em for 30 minutes or so, then drop the mag drag down and do a bit of one legged cranking. Too boring but I always do better come spring - no saddle sores, better leg endurance, no wrist or shoulder pain from turning couch potato for the winter.
The rig sits in front of a window, looking at the horse pasture. I grind away to tunes on the stereo, watching the horses. They watch me too, probably thinking "WTF is that idiot doing? Works real hard, goes nowhere, don't look happy and they call us dumb animals". I keep the Moto's stem shifters up against 'the fire wall' in top gear and just turn em for 30 minutes or so, then drop the mag drag down and do a bit of one legged cranking. Too boring but I always do better come spring - no saddle sores, better leg endurance, no wrist or shoulder pain from turning couch potato for the winter.
#9
Senior Member
Join Date: Aug 2013
Posts: 2,321
Mentioned: 35 Post(s)
Tagged: 0 Thread(s)
Quoted: 767 Post(s)
Liked 1,898 Times
in
889 Posts
DO these come in bib form? It's for a friend...
(kidding, kidding)
I try to be aggressive when it comes to surface rust on my bikes. My Ironman had it at the cable guides on the top tube.
I used a sanding/wire brush combo and then touched up with primer and paint.
As long as I get the rust off and covered with something to protect the steel - paint, oil, grease, etc. - I'm good.
One can always repaint or powder coat down the road. But stop that rust in its tracks.
(kidding, kidding)
Curious is anyone is mounting and using their bike(s) on a trainer? I had my Mercian on a smart trainer for a while and apparently I wasn't too good at wiping the sweat off afterwards and now have some surface rust spots. Sooo, part two of the question what's the best way to deal with surface rust?
I used a sanding/wire brush combo and then touched up with primer and paint.
As long as I get the rust off and covered with something to protect the steel - paint, oil, grease, etc. - I'm good.
One can always repaint or powder coat down the road. But stop that rust in its tracks.
#10
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,396
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,696 Times
in
2,517 Posts
As far as rust goes, I spray down the frame with camelia oil occasionally. T9 or some other rust protecting spray would probably work just as well. The Semipro was full chrome, so somewhat more resistant to rust than many bikes.
#11
Full Member
I'm using on my trainer an aero Kettler Strato from the mid-'80s. Glued aluminum frame, has not yet begun to rust, but I keep my eyes on it. Of course, with a shimano ax 6300 set for minimal air resistance.:
#12
Junior Member
Join Date: Jul 2019
Location: far western MD
Posts: 98
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 41 Post(s)
Likes: 0
Liked 39 Times
in
24 Posts
Don't use a bike you care about. Years ago I totally destroyed my "bought new in 1973" Fugi S10S on a trainer.
I had it set up with a big fan blowing air and a TV to watch. Reminded me of being at work testing vehicles on a chassis dyno with a "video drivers aid" ( for the test cycle) and cooling fan.
I had it set up with a big fan blowing air and a TV to watch. Reminded me of being at work testing vehicles on a chassis dyno with a "video drivers aid" ( for the test cycle) and cooling fan.
#13
Old Legs
Join Date: Nov 2016
Location: Mass.
Posts: 1,212
Bikes: '80 Strayvaigin, '84 Ciocc Aelle-Shimano 105, '90 Concorde Astore /Campy Triple ,85 Bridgestone 500/Suntour, 2005 Jamis Quest, 2017 Raleigh Merit 1, Raleigh Carbon Clubman
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 302 Post(s)
Liked 33 Times
in
22 Posts
Here's my '90 Concorde, setup. The gray cover on top tube, is from a Blackburn trainer. Never had an issue with sweat, but the bike gets a wipe down and lube, before going back on the road, in the Spring.KB
#14
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,874
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1856 Post(s)
Liked 664 Times
in
506 Posts
Wahoo has yet to release a freewheel adapter for the Kickr so I'm stuck using my modern bikes on the trainer, but sweat is sweat and bad for any bike. I have an air mover in front of me and a smaller fan behind the trainer aimed at my lower back, a sweat catcher on the bike, and I wear a base layer, sweat band, and fingerless gloves to help manage the sweat that does form.
#15
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,874
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1856 Post(s)
Liked 664 Times
in
506 Posts
Oh, and I use a bike bathrobe on most of my CVs.
#16
Junior Member
Thread Starter
Join Date: Apr 2016
Location: Dallas
Posts: 132
Bikes: Current Stable: 1973 Mercian Vincitore;1985 CIOCC Designer'84;1988 Raleigh "531c USA" ;1990 LeMond Maillot Jaune Z Team; 1991 Fuji Titanium;1996 Calfee LunaPro-Lemond Z team Tribute Replica; 2013 Wilier Zero.Seven
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 47 Post(s)
Liked 31 Times
in
14 Posts
Guys,
thanks for all of the comments and suggestions. I think that one of the things that I've concluded (because I sold my old Tempo and it was my old "trainer" bike), the quality of the painting and paint prep? of a 1970s English bike is probably no where as good as say a mid 80s Japanese frame (my Tempo was a Panasonic Tange2 frame and never a hint of rust). I think, I might be finding myself in the market for a new "trainer" bike
thanks for all of the comments and suggestions. I think that one of the things that I've concluded (because I sold my old Tempo and it was my old "trainer" bike), the quality of the painting and paint prep? of a 1970s English bike is probably no where as good as say a mid 80s Japanese frame (my Tempo was a Panasonic Tange2 frame and never a hint of rust). I think, I might be finding myself in the market for a new "trainer" bike