Can someone help me understand adjusting a Dura Ace AX derailleur.
#1
Senior Member
Thread Starter
Join Date: Jun 2018
Location: NW Ohio
Posts: 1,142
Bikes: 1983 Univega Super Strada, 1986 Panasonic DX5000, 1984 Fuji Team 85 Univega Gran Turismo, 1984 Lotus Unique, 1987 Centurion Expert, 1987 Centurion Ironman Master,
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 677 Post(s)
Liked 459 Times
in
182 Posts
Can someone help me understand adjusting a Dura Ace AX derailleur.
I have the instructions but can't seem to understand which screw is which on the diagram.
Is the gold screw in the photo the center adjustment screw? And then there is a select screw.
I can only find one other screw on the derailleur and it is the one right above the center adjustment
screw> It looks in a different place in their diagram. Here is a photo and the diagram.
Is the gold screw in the photo the center adjustment screw? And then there is a select screw.
I can only find one other screw on the derailleur and it is the one right above the center adjustment
screw> It looks in a different place in their diagram. Here is a photo and the diagram.
#2
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,837
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 805 Post(s)
Liked 706 Times
in
377 Posts
The screw in the upper body of the derailleur is the high-gear limit screw. Adjust the upper and lower limit screws, attach the cable, then use the "select screw" to fine tune the adjustments on the cogs.
I think. It's been nearly 40 years since I worked on one of those.
I think. It's been nearly 40 years since I worked on one of those.
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
#3
Senior Member
Thread Starter
Join Date: Jun 2018
Location: NW Ohio
Posts: 1,142
Bikes: 1983 Univega Super Strada, 1986 Panasonic DX5000, 1984 Fuji Team 85 Univega Gran Turismo, 1984 Lotus Unique, 1987 Centurion Expert, 1987 Centurion Ironman Master,
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 677 Post(s)
Liked 459 Times
in
182 Posts
The screw in the upper body of the derailleur is the high-gear limit screw. Adjust the upper and lower limit screws, attach the cable, then use the "select screw" to fine tune the adjustments on the cogs.
I think. It's been nearly 40 years since I worked on one of those.
I think. It's been nearly 40 years since I worked on one of those.
#4
Blamester
Not to be flippant but if there are only two screws turn them and see what happens.
And if nothing happens turn them untill something does happen.
Be careful and take the weight of the screw by moving the derailleur by hand to a different position.
Use a good screwdriver because you don't want to strip those.
Bye the way I have never worked on one of these.
And if nothing happens turn them untill something does happen.
Be careful and take the weight of the screw by moving the derailleur by hand to a different position.
Use a good screwdriver because you don't want to strip those.
Bye the way I have never worked on one of these.
#5
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,986
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,809 Times
in
3,317 Posts
There may not be any limit screws. But not certain. This is pre-indexed shifting and small cassette stack width.
Not sure but one of those screws you are talking about is the hold fast for the cable, isn't it? The smaller might be controlling how the pulley wheel springs back to a different position with shifting.
This type DR design was a one-off thing for Shimano back in the day. Probably just being ready to go in different directions if DR's of a different brand and design seemed to be the markets leaning.
This is the AX II. Not sure how helpful it is for yours........
https://si.shimano.com/pdfs/si/SI-M-86-000-00-ENG.pdf
Not sure but one of those screws you are talking about is the hold fast for the cable, isn't it? The smaller might be controlling how the pulley wheel springs back to a different position with shifting.
This type DR design was a one-off thing for Shimano back in the day. Probably just being ready to go in different directions if DR's of a different brand and design seemed to be the markets leaning.
This is the AX II. Not sure how helpful it is for yours........
https://si.shimano.com/pdfs/si/SI-M-86-000-00-ENG.pdf
Last edited by Iride01; 09-02-20 at 10:57 AM.
#6
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,624
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1324 Post(s)
Liked 927 Times
in
640 Posts
IIRC, one of those screws sets the derailleur to one of a number of # of cogs. It can be adjusted for 6 or 7 cogs. Also, I believe it was sort of index in theat the indexing was in the derailleur not the shifter.
When I set mine up, I used one screw to limit the travel to the largest cog but not beyond. I believe it's the small screw up near the mounting bolt. The other screw sets the # of cogs. Six cogs were the original Dura Ace AX number.
Cheers
When I set mine up, I used one screw to limit the travel to the largest cog but not beyond. I believe it's the small screw up near the mounting bolt. The other screw sets the # of cogs. Six cogs were the original Dura Ace AX number.
Cheers
#7
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,845
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,822 Times
in
1,541 Posts
There may not be any limit screws. But not certain. This is pre-indexed shifting and small cassette stack width.
Not sure but one of those screws you are talking about is the hold fast for the cable, isn't it? The smaller might be controlling how the pulley wheel springs back to a different position with shifting.
This type DR design was a one-off thing for Shimano back in the day. Probably just being ready to go in different directions if DR's of a different brand and design seemed to be the markets leaning.
This is the AX II. Not sure how helpful it is for yours........
https://si.shimano.com/pdfs/si/SI-M-86-000-00-ENG.pdf
Not sure but one of those screws you are talking about is the hold fast for the cable, isn't it? The smaller might be controlling how the pulley wheel springs back to a different position with shifting.
This type DR design was a one-off thing for Shimano back in the day. Probably just being ready to go in different directions if DR's of a different brand and design seemed to be the markets leaning.
This is the AX II. Not sure how helpful it is for yours........
https://si.shimano.com/pdfs/si/SI-M-86-000-00-ENG.pdf
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#8
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,513
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,394 Times
in
2,056 Posts
#9
Senior Member
Thread Starter
Join Date: Jun 2018
Location: NW Ohio
Posts: 1,142
Bikes: 1983 Univega Super Strada, 1986 Panasonic DX5000, 1984 Fuji Team 85 Univega Gran Turismo, 1984 Lotus Unique, 1987 Centurion Expert, 1987 Centurion Ironman Master,
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 677 Post(s)
Liked 459 Times
in
182 Posts
Seems different in that you adjust the derailleur pully for each individual gear even though it is a friction derailleur.
#10
Senior Member
Thread Starter
Join Date: Jun 2018
Location: NW Ohio
Posts: 1,142
Bikes: 1983 Univega Super Strada, 1986 Panasonic DX5000, 1984 Fuji Team 85 Univega Gran Turismo, 1984 Lotus Unique, 1987 Centurion Expert, 1987 Centurion Ironman Master,
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 677 Post(s)
Liked 459 Times
in
182 Posts
The instructions I posted don't make sense... If you adjust the pully for each gear doesn't each adjustment change all previous adjustments?
#11
Banned
take it off hold it in your hand and try to understand what the screws do.
RD really have a inner & outer stroke limit screw..
some have a B screw that forces it to rotate to increase inner clearance over low gear cog...
Found any more source material on this your self, yet?
1st bike you worked on? If so, it's an odd one to begin with ..
pick up Lennard Zinn's road bike mechanics book and a few more titles.. to understand the basics..
...
RD really have a inner & outer stroke limit screw..
some have a B screw that forces it to rotate to increase inner clearance over low gear cog...
Found any more source material on this your self, yet?
1st bike you worked on? If so, it's an odd one to begin with ..
pick up Lennard Zinn's road bike mechanics book and a few more titles.. to understand the basics..
...
#12
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,513
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,394 Times
in
2,056 Posts
#13
Senior Member
Thread Starter
Join Date: Jun 2018
Location: NW Ohio
Posts: 1,142
Bikes: 1983 Univega Super Strada, 1986 Panasonic DX5000, 1984 Fuji Team 85 Univega Gran Turismo, 1984 Lotus Unique, 1987 Centurion Expert, 1987 Centurion Ironman Master,
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 677 Post(s)
Liked 459 Times
in
182 Posts
I would call a notch in the derailleur itself no click in the shifter and not a strong notch
but you can tell when it hits the next gear. Kind of between a pure friction and an indexed
system. I haven't ridden it enough to tell if I really like it. I do like friction shifting though.