Frame Pump recommendation
#1
Live Healthy
Thread Starter
Join Date: Jun 2020
Posts: 417
Bikes: Wabi Classic
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 183 Post(s)
Liked 137 Times
in
92 Posts
Frame Pump recommendation
Hey guys I’m looking for a frame pump and hoping to get some advice on which pump works best. Hoping not to spend over $50
#2
Newbie
Likes For Amber1988:
#3
Junior Member
#4
Senior Member
Didn't know you could get pump-up frames now. Do you find it stiff enough?
Likes For jgwilliams:
#5
Senior Member
The Blackburn Road Morph is my favorite pump. You can set the end of the pump on the ground (there is a fold out tab you can put your foot on to hold it steady. I like this pump because it is nearly as small and light as a micro pump, but easily pumps up tires to over 100 psi. Other small pumps (and vintage frame pumps) have to be held with both hands, which is little clumsy, and makes it hard to inflate tires to high pressures.
Likes For 50PlusCycling:
#6
Senior Member
Join Date: Oct 2015
Posts: 15,488
Bikes: 2015 Workswell 066, 2017 Workswell 093, 2014 Dawes Sheila, 1983 Cannondale 500, 1984 Raleigh Olympian, 2007 Cannondale Rize 4, 2017 Fuji Sportif 1 LE
Mentioned: 144 Post(s)
Tagged: 0 Thread(s)
Quoted: 7652 Post(s)
Liked 3,473 Times
in
1,834 Posts
My current favorite is made by Lezyne, maybe called the HP .... it has a detachable flexible hose which makes it easier to operate the pump without stressing the valve. I find I can hit over 100 psi very quickly,, unlike other frame pumps I have used.
#7
Senior Member
Shouldn't that be Topeak Road Morph. Yes, it's a neat piece of design. I think all of my pumps are Topeak except for a couple of Zefal frame fitting pumps which I have on my old steel bikes. Personally I like the Pocket Rocket. It's light enough not to be noticeable but good enough if you do ever need to use out on the road, which I hope never to do. 99% of my pump duties are carried out by the Joe Blow, which is an excellent pump but definitely won't fit on the bike.
Likes For jgwilliams:
#8
-------
Join Date: Jul 2020
Location: Tejas
Posts: 12,795
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 9653 Post(s)
Liked 6,365 Times
in
3,505 Posts
#9
Junior Member
rotors and rapidly moving fingers/hand nearby don't go well together. irritation (fixing a roadside flat), small pump with aching muscles, unbalanced wheel/bike placement, distraction (traffic whizzing by) and other factors may lead to hand/fingers coming in contact with the rotors. Rotors contamination would be the second thing on my mind :wink:
i would try to pump from the other side of rotors. (and personal choice, tube stem at top, pump from above tire, pumping downwards inward angle, but, thats probably because i prefer standing)
i would try to pump from the other side of rotors. (and personal choice, tube stem at top, pump from above tire, pumping downwards inward angle, but, thats probably because i prefer standing)
Last edited by shrimp123; 10-22-20 at 11:42 AM.
#10
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,506
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4348 Post(s)
Liked 3,985 Times
in
2,661 Posts
Seriously do we really need another one of these. TOPEAK ROAD MORPH. It has been said a billion frikkin times here. There are many threads on this and the vote tends to be highest for the Topeak Road Morph because it is a fantastic pump that is easy to use and practical.
Likes For veganbikes:
#11
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,957
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 880 Times
in
527 Posts
Zefal HPX.
Unless you need a compact pump, then just pick one. Topeak is a good product (I have two of them) but I've used a variety of others and they all are ok.
Unless you need a compact pump, then just pick one. Topeak is a good product (I have two of them) but I've used a variety of others and they all are ok.
Likes For Moe Zhoost:
#13
Senior Member
Join Date: Oct 2008
Location: Portland, OR
Posts: 3,842
Bikes: Trek Domane SL6 Gen 3, Soma Fog Cutter, Focus Mares AL, Detroit Bikes Sparrow FG, Volae Team, Nimbus MUni
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 896 Post(s)
Liked 2,063 Times
in
1,081 Posts
I have a Road Morph; gets the job done but bulky and heavy and ugly as sin on my new bike.
It has a hose, so you're less likely to break a valve stem. It has a lever hose end, so you're not going to unscrew your removable core. One end plants on the ground, so you can put your weight into it. It's robust.
On a 1200k brevet, fixing a flat at dusk in the middle of frickin' nowhere eastern Oregon, I was thinking about how much time I had in the bank, how much water was in my bottles and snacks in my pockets, and if my wife was going to freak because my satellite tracker would show me stopped in the middle of frickin' nowhere. One thing I didn't worry about was my pump. Sometimes I think about getting something prettier on the bike, then I think about being on the side of the road where pretty doesn't matter.
It has a hose, so you're less likely to break a valve stem. It has a lever hose end, so you're not going to unscrew your removable core. One end plants on the ground, so you can put your weight into it. It's robust.
On a 1200k brevet, fixing a flat at dusk in the middle of frickin' nowhere eastern Oregon, I was thinking about how much time I had in the bank, how much water was in my bottles and snacks in my pockets, and if my wife was going to freak because my satellite tracker would show me stopped in the middle of frickin' nowhere. One thing I didn't worry about was my pump. Sometimes I think about getting something prettier on the bike, then I think about being on the side of the road where pretty doesn't matter.
#16
jj
Join Date: Jul 2019
Posts: 331
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 140 Post(s)
Liked 110 Times
in
78 Posts
rotors and rapidly moving fingers/hand nearby don't go well together. irritation (fixing a roadside flat), small pump with aching muscles, unbalanced wheel/bike placement, distraction (traffic whizzing by) and other factors may lead to hand/fingers coming in contact with the rotors. Rotors contamination would be the second thing on my mind :wink:
i would try to pump from the other side of rotors. (and personal choice, tube stem at top, pump from above tire, pumping downwards inward angle, but, thats probably because i prefer standing)
i would try to pump from the other side of rotors. (and personal choice, tube stem at top, pump from above tire, pumping downwards inward angle, but, thats probably because i prefer standing)
back OT- I like the Topeak Road Morph for the same reasons mentioned earlier for the first three or four times I use it, but the next fifteen to twenty are a pain due to the rubber growing and not wanting to let the tube valve up into it. Due to having experienced it on one of their regular full length frame pumps I think this is just a Topeak problem. Most bike shops are aware of it being a wear item and have them in stock and ready to sell for a couple bucks.
I also have a Zefal regular full lengther which I haven’t used enough to judge its durability. It works fine and looks nice in black on a black hardware bike.
#17
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,902
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4802 Post(s)
Liked 3,923 Times
in
2,552 Posts
Zephal HPX fan here. I've been using HPXs (and the previous HPs) sine 1973 because they work, reach any pressure I will ever need and are easy to use. (They do take a touch of skill to hold them so you do not damage the valve stem. I find wrapping my fingers around the spokes does the job just fine.)
Yes, hoses are kinder to valve stems. But screwing them on and off gets old. And on some pumps. you have to unscrew the hose as well and stash it. The HPXx are so simple. Press on the head, flip the lever, pump. Flip lever off and remove. Done. The lever means that the chuck is relaxed when engaging and removing and sees far less wear from the valve stem threads. The gasket and pump last years with every day use. (For 10 years I did not own a floor pump; just the HPs on my bikes. Rode sew-ups, raced latex tubes. Those pumps were completely up to the job. The current HPXs are just a little easier to pump.)
On group rides, those Zephals are the pumps that get used when other means fail.
Ben
Yes, hoses are kinder to valve stems. But screwing them on and off gets old. And on some pumps. you have to unscrew the hose as well and stash it. The HPXx are so simple. Press on the head, flip the lever, pump. Flip lever off and remove. Done. The lever means that the chuck is relaxed when engaging and removing and sees far less wear from the valve stem threads. The gasket and pump last years with every day use. (For 10 years I did not own a floor pump; just the HPs on my bikes. Rode sew-ups, raced latex tubes. Those pumps were completely up to the job. The current HPXs are just a little easier to pump.)
On group rides, those Zephals are the pumps that get used when other means fail.
Ben
Likes For 79pmooney:
#19
Senior Member
Join Date: Oct 2015
Posts: 15,488
Bikes: 2015 Workswell 066, 2017 Workswell 093, 2014 Dawes Sheila, 1983 Cannondale 500, 1984 Raleigh Olympian, 2007 Cannondale Rize 4, 2017 Fuji Sportif 1 LE
Mentioned: 144 Post(s)
Tagged: 0 Thread(s)
Quoted: 7652 Post(s)
Liked 3,473 Times
in
1,834 Posts
Zephal HPX fan here. I've been using HPXs (and the previous HPs) sine 1973 because they work, reach any pressure I will ever need and are easy to use. (They do take a touch of skill to hold them so you do not damage the valve stem. .........
Yes, hoses are kinder to valve stems. But screwing them on and off gets old. ......
Yes, hoses are kinder to valve stems. But screwing them on and off gets old. ......
I have a variety of pumps. With lock-on pumps I do what you do---either hold some neighboring spokes, or I lean the wheel on my leg and push the pump-head into my knee. I have bent a couple stem-cores and had a couple break, and that sucks because the tube itself might be fine but without a valve ......
But whatever. Three or four bent or broken cores in five decades of riding .... not a thing.
And how often do you get flats, that you get tired of screwing on a valve? Seven or eight flats per ride? You claim that you have so many flats that threading the pump on wears out your valves? Really?
I really don't care what pump anyone else uses ... but some of the reasons why are fairly amusing.
What I care about is how many strikes it takes to get to 100-120 psi. That is pretty much the issue. Beyond that i can adapt.
Likes For Maelochs:
#20
Senior Member
Join Date: Jan 2010
Posts: 39,232
Mentioned: 211 Post(s)
Tagged: 1 Thread(s)
Quoted: 18409 Post(s)
Liked 15,530 Times
in
7,326 Posts
Notorious RMG. Use it for touring and commuting, but I don’t mount it to the frame for the reasons mentioned above. Also, the gauge is hard to read unless you have a hawk’s vision.
#21
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,528
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3664 Post(s)
Liked 5,410 Times
in
2,748 Posts
Where is the psycho thread where the OP insisted the Road Morph was/was not a "frame" pump? That was a classic.
#22
Senior Member
Join Date: May 2012
Location: western Massachusetts (greater Springfield area)
Posts: 699
Bikes: Velosolex St. Tropez, LeMond Zurich (spine bike), Rotator swb recumbent
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 67 Post(s)
Likes: 0
Liked 67 Times
in
32 Posts
I have Blackburn (or old Nashbar knockoff) pumps on my bikes. They have the lever heads, and handles that open up into a T. I lock the head on the valve, lean the wheel over almost horizontal on the ground with the pump head on a rock, curb, root or whatever, and I can lean into it with no risk of breaking the valve. It is almost like a floor pump; much faster than a mini pump, and I get more than 2 tries like with CO2. I get back up to 110-120 PSI in short order. My bikes all have straight tubes; might be a problem where to mount it on a swoopier ride.
#23
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,902
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4802 Post(s)
Liked 3,923 Times
in
2,552 Posts
Breaking off the valve stem core doesn't get old?
I have a variety of pumps. With lock-on pumps I do what you do---either hold some neighboring spokes, or I lean the wheel on my leg and push the pump-head into my knee. I have bent a couple stem-cores and had a couple break, and that sucks because the tube itself might be fine but without a valve ......
But whatever. Three or four bent or broken cores in five decades of riding .... not a thing.
And how often do you get flats, that you get tired of screwing on a valve? Seven or eight flats per ride? You claim that you have so many flats that threading the pump on wears out your valves? Really?
I really don't care what pump anyone else uses ... but some of the reasons why are fairly amusing.
What I care about is how many strikes it takes to get to 100-120 psi. That is pretty much the issue. Beyond that i can adapt.
I have a variety of pumps. With lock-on pumps I do what you do---either hold some neighboring spokes, or I lean the wheel on my leg and push the pump-head into my knee. I have bent a couple stem-cores and had a couple break, and that sucks because the tube itself might be fine but without a valve ......
But whatever. Three or four bent or broken cores in five decades of riding .... not a thing.
And how often do you get flats, that you get tired of screwing on a valve? Seven or eight flats per ride? You claim that you have so many flats that threading the pump on wears out your valves? Really?
I really don't care what pump anyone else uses ... but some of the reasons why are fairly amusing.
What I care about is how many strikes it takes to get to 100-120 psi. That is pretty much the issue. Beyond that i can adapt.
HPX - around 100 strokes to get to well over 100 psi in say 25c tires.
#24
Senior Member
I still have a couple of old Zefal HPXs from 25-30 years ago, but these days I only carry Road Morphs.
#25
Senior Member
Join Date: Nov 2010
Location: Along the Rivers of Pittsburgh
Posts: 1,255
Bikes: 2011 Novara Forza Hybrid, 2005 Trek 820, 1989 Cannondale SR500 Black Lightning, 1975 Mundo Cycles Caloi Racer
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 258 Post(s)
Liked 291 Times
in
157 Posts
My daughter has a Crank Bros. Gem pump. Kinda interesting design that can change from high volume or high pressure with a turn of the base of the pump. I have never used it but I find it intriguing.
I have a Topeak Road Morph that has saved me from the phone call of shame a few times. Being able to put the base on the ground makes all the different in getting up to full pressure.
Here's a link to the Gem:
https://www.crankbrothers.com/produc...nt=53958772039
I have a Topeak Road Morph that has saved me from the phone call of shame a few times. Being able to put the base on the ground makes all the different in getting up to full pressure.
Here's a link to the Gem:
https://www.crankbrothers.com/produc...nt=53958772039