Fouled Steerer Threads - Richard Sachs
#1
Zip tie Karen
Thread Starter
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Fouled Steerer Threads - Richard Sachs
Okay, I need help from the collective wisdom. Late 70s Sachs frame recently repainted and entrusted to me for the reassembly. Whoever handled the fork before me buggered up the steerer initial threads.
Last edited by Phil_gretz; 07-10-20 at 02:36 PM.
#2
Zip tie Karen
Thread Starter
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Campy Headset...
with aluminum threaded parts.
It's all beautiful stuff...
It's all beautiful stuff...
#3
Zip tie Karen
Thread Starter
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
The frame and fork are beautiful...
and I don't want to screw this up. It's for a friend.
#4
Zip tie Karen
Thread Starter
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
So, What's next?
I cannot force aluminum threaded parts over those buggered threads. I need to remove the fouling. Chase with a steel headset nut? I'm frozen with fear...
Help?
Help?
#5
Senior Member
Join Date: Oct 2009
Location: Sherwood, OR
Posts: 1,279
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 336 Post(s)
Liked 309 Times
in
180 Posts
My shop has a die for threading steerer tubes, https://www.universalcycles.com/shop...s.php?id=44333
Your best bet is a shop that has been around for a while, or a Co-Op that works on old bikes.
Your best bet is a shop that has been around for a while, or a Co-Op that works on old bikes.
#6
Senior Member
Join Date: Jun 2020
Location: Oregon
Posts: 71
Bikes: Flex, Volkscycle MarkX
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 12 Times
in
5 Posts
Get a small triangular file and carefully chase the threads, it will work. Then thread new nut on. If you have a large steel nut that would be good to run down the threads on after using the file. A die that size is likely to be expensive.
Last edited by quindecima; 07-10-20 at 03:47 PM.
Likes For quindecima:
Likes For fietsbob:
#9
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
I'd go with careful, patient file work; the problem with a die is getting it started properly aligned with the existing threads. Get it wrong and you have made the problem a lot worse.
Likes For dsbrantjr:
#10
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,509
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2745 Post(s)
Liked 3,390 Times
in
2,053 Posts
This. Careful, patient, wear cheaters.
Likes For dedhed:
#11
Zip tie Karen
Thread Starter
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
^ I can do this...
#12
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,037
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 341 Times
in
251 Posts
All the guys I respect say the same thing: use a triangular file to chase just those last few threads. Start with the file in a good thread, get it up near where the crud is, then gently see if you can get the crud off. Observe where the file is cutting and repeat. Easy does it.
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
Likes For WizardOfBoz:
#13
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,984
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26404 Post(s)
Liked 10,374 Times
in
7,203 Posts
.
...I have one of those steerer threading die tools from Hozan, that I got when a local shop closed, but I wouldn't break it out for that.
Even if you're not very good with a file, losing the first thread or so is not a big deal, unless your steerer is pretty short for the headset stack height.
So worst case scenario is that you file it down and lose the thread that's damaged, but it clears enough so your headset parts will thread on square.
Whereas if you're not very good with the threading die, you can get into all kinds of trouble.
After the cleanup, I do think I'd run a steel headset race up and down a time or two before I tried the aluminum stuff, just to make sure everything is clean and unobstructed.
You can still get the transfers for a 70's Sachs from his painter, (Joe Bell, I think, if he's still painting stuff). He gets them made up in batches by someone he calls the "Decal Wizard". It can take a while to get them, but they're about the same price as any other decals. He might want a picture of your frame details to ID it as a genuine Sachs. The frame builder is understandably anxious about counterfeiting.
...I have one of those steerer threading die tools from Hozan, that I got when a local shop closed, but I wouldn't break it out for that.
Even if you're not very good with a file, losing the first thread or so is not a big deal, unless your steerer is pretty short for the headset stack height.
So worst case scenario is that you file it down and lose the thread that's damaged, but it clears enough so your headset parts will thread on square.
Whereas if you're not very good with the threading die, you can get into all kinds of trouble.
After the cleanup, I do think I'd run a steel headset race up and down a time or two before I tried the aluminum stuff, just to make sure everything is clean and unobstructed.
You can still get the transfers for a 70's Sachs from his painter, (Joe Bell, I think, if he's still painting stuff). He gets them made up in batches by someone he calls the "Decal Wizard". It can take a while to get them, but they're about the same price as any other decals. He might want a picture of your frame details to ID it as a genuine Sachs. The frame builder is understandably anxious about counterfeiting.
Likes For 3alarmer:
#14
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,551
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 582 Times
in
399 Posts
There are *METRIC* thread files too!
METRIC THREAD FILE
EDIT: The advantage of this file is that the adjacent good threads guide the file to restore the damaged ones.
METRIC THREAD FILE
EDIT: The advantage of this file is that the adjacent good threads guide the file to restore the damaged ones.
Last edited by sweeks; 07-10-20 at 07:34 PM.
Likes For sweeks:
#15
aka: Dr. Cannondale
Join Date: Jul 2009
Posts: 7,729
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2152 Post(s)
Liked 3,402 Times
in
1,203 Posts
Richard will sell you correct decals directly once provenance is confirmed. They are not cheap, but they are lovely. And correct.
__________________
Hard at work in the Secret Underground Laboratory...
Hard at work in the Secret Underground Laboratory...
#16
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,984
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26404 Post(s)
Liked 10,374 Times
in
7,203 Posts
#17
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,505
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4348 Post(s)
Liked 3,985 Times
in
2,661 Posts
Look I hate to be the bearer of bad news and so sorry that nobody else was brave enough to tell you but the entire frame is trashed and you should send it to me so I can get it to the proper metal recyclers so it doesn't further harm the planet or get anyone killed. I work with some good recycling centers that make sure deadly frames and headsets like that don't wind up in the wrong hands and kill again.
Tell your friend I am saving their life but know I am not a hero for doing this just a regular schmuck trying to do a little good.
Tell your friend I am saving their life but know I am not a hero for doing this just a regular schmuck trying to do a little good.
#18
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,957
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 880 Times
in
527 Posts
All the guys I respect say the same thing: use a triangular file to chase just those last few threads. Start with the file in a good thread, get it up near where the crud is, then gently see if you can get the crud off. Observe where the file is cutting and repeat. Easy does it.
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
Likes For Moe Zhoost:
#19
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
#20
Senior Member
Join Date: Jun 2020
Location: Maryland
Posts: 1,380
Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 668 Post(s)
Liked 529 Times
in
355 Posts
I've had mixed luck with files for jobs like that. A thread chase is risky because you first need to thread it on. With a screwed up first thread there is a high chance of cross threading.
With the picture you have a pointed awl might help you reshape that first thread. Just drag it though the root of the thread
Don't know that I would use a thread restoring file for just the top thread.
Like someone else said if you have sufficient thread engagement you can generally afford to lose the first thread or so. I have a small belt sander used for sharpening knives. With a light touch and fine grit you can probably *taper* off that first thread so you can get to the clean one below it. I would only do that after cleaning it up with the awl.
Excellent read
https://www.parktool.com/blog/repair...hread-concepts
With the picture you have a pointed awl might help you reshape that first thread. Just drag it though the root of the thread
Don't know that I would use a thread restoring file for just the top thread.
Like someone else said if you have sufficient thread engagement you can generally afford to lose the first thread or so. I have a small belt sander used for sharpening knives. With a light touch and fine grit you can probably *taper* off that first thread so you can get to the clean one below it. I would only do that after cleaning it up with the awl.
Excellent read
https://www.parktool.com/blog/repair...hread-concepts
Last edited by Pop N Wood; 07-12-20 at 10:01 AM.
Likes For Pop N Wood:
#21
Banned
All the guys I respect say the same thing: use a triangular file to chase just those last few threads. Start with the file in a good thread, get it up near where the crud is, then gently see if you can get the crud off. Observe where the file is cutting and repeat. Easy does it.
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
..
I would NOT use a die to chase those threads.
BTW, you could also use a thread restoring file (probably a 24 tpi one) as below:
..
#23
Senior Member
Join Date: Mar 2010
Posts: 1,659
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1248 Post(s)
Liked 1,323 Times
in
674 Posts
I was a tool and die maker by trade and I would strongly suggest not to start fooling around its files and misc. thread files. Find a bike a bike shop with proper head tube die threader to clear up the fork. I work as a mill right as well and still it would be a last choice to start fooling around with a needle file.
#24
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,509
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2745 Post(s)
Liked 3,390 Times
in
2,053 Posts
I was a tool and die maker by trade and I would strongly suggest not to start fooling around its files and misc. thread files. Find a bike a bike shop with proper head tube die threader to clear up the fork. I work as a mill right as well and still it would be a last choice to start fooling around with a needle file.
Likes For dedhed:
#25
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
Isn't it just the first thread that is boogered up? Just file that away with a flat bastard file or lightly touch it on a belt sander with the belt running toward the inside of the tube. A belt sander on a stand would be my preference, then a flat file, then a hand held belt sander. Heck even a strip of emery cloth.
A die will be an issue because this is on the starting thread of the tube. A thread file will be an issue because you don't need to remove any material but that ugly burr on the first thread. You might can get away with a triangular file, but you will be removing material of the thread that is not messed up too. If you use a triangular file, use it like you would a flat file or sanding belt and go across from outside to inside.
A die will be an issue because this is on the starting thread of the tube. A thread file will be an issue because you don't need to remove any material but that ugly burr on the first thread. You might can get away with a triangular file, but you will be removing material of the thread that is not messed up too. If you use a triangular file, use it like you would a flat file or sanding belt and go across from outside to inside.