What's normal air loss for tires?
#1
Unlisted member
Thread Starter
Join Date: Dec 2005
Location: Chicagoland
Posts: 6,192
Bikes: Specialized Hardrock
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1376 Post(s)
Liked 432 Times
in
297 Posts
What's normal air loss for tires?
After a series of flats averaging 10 miles/tube using a Performance Forte Metro tires I replaced both the tire and tube with a WTB slick and another Forte tube. There were some small bits of glass in the tread that couldn't be felt but were pressed into the tube during use, and both the rim and rim strip were new this spring. There's nothing on the rim that I can see that would cause a puncture either. The original tire has been used for years on both the front and rear wheels, and is inflated to a maximum pressure of 60 pounds. I usually check the pressure weekly, and often it seems like I ended up replacing the air lost by checking the pressure. The new tire can be inflated to 85 pounds, and I inflated it to 80 on Wednesday. The first ride I took was Friday morning, and when I got the office the pressure had dropped to 60 pounds. While that's a lot more pressure lost than the previous tires, it's not that different from the losses I'm used to seeing in my GF's tires that are inflated to the same pressure except for the time - she doesn't ride that often and it can be a couple weeks between rides for her and I've never checked the pressure in her tires after a couple of days. Searching the forums here naturally produced a variety of conflicting advice as to whether this is normal or not - am I going to have to top off this tire every couple of days?!?!
#2
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
80 down to 60 in a commute... you have a slow leak somewhere.
normally will go down a couple psi a day.
I check tires and top off before every ride.
A habit from riding tubulars for over 10 years.
normally will go down a couple psi a day.
I check tires and top off before every ride.
A habit from riding tubulars for over 10 years.
#4
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,967
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1839 Post(s)
Liked 1,712 Times
in
988 Posts
To be clear, air loss has nothing to do with the tires. Any air loss is due either to permeability of the inner tube or a leak in the tube
#5
Hack
Join Date: Sep 2015
Location: Ottawa, Ontario, Canada
Posts: 1,274
Bikes: TrueNorth CX bike, 88 Bianchi Strada (currently Sturmey'd), Yess World Cup race BMX, Pure Cruiser race BMX, RSD Mayor v3 Fatbike
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 347 Post(s)
Liked 197 Times
in
135 Posts
I'd say try it again - hope it was the valve not 100% sealed, and it seats better next time. From what you describe, I don't think you checked the pressure before your ride on Friday, so it was really two days and a ride.
I do find that when I put in a new (or patched) tube, I'll see more leak-down for the first week or two than later on. I run 700x28's at 70/75psi, and I only top up once or twice a week, once I'm past that initial period. I top up every day after replacing a tube.
I have a theory as to why, but really need to talk to someone better with fluid dynamics to see if it's remotely plausible.
I do find that when I put in a new (or patched) tube, I'll see more leak-down for the first week or two than later on. I run 700x28's at 70/75psi, and I only top up once or twice a week, once I'm past that initial period. I top up every day after replacing a tube.
I have a theory as to why, but really need to talk to someone better with fluid dynamics to see if it's remotely plausible.
#6
Unlisted member
Thread Starter
Join Date: Dec 2005
Location: Chicagoland
Posts: 6,192
Bikes: Specialized Hardrock
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1376 Post(s)
Liked 432 Times
in
297 Posts
I'd say try it again - hope it was the valve not 100% sealed, and it seats better next time. From what you describe, I don't think you checked the pressure before your ride on Friday, so it was really two days and a ride.
I do find that when I put in a new (or patched) tube, I'll see more leak-down for the first week or two than later on. I run 700x28's at 70/75psi, and I only top up once or twice a week, once I'm past that initial period. I top up every day after replacing a tube.
I have a theory as to why, but really need to talk to someone better with fluid dynamics to see if it's remotely plausible.
I do find that when I put in a new (or patched) tube, I'll see more leak-down for the first week or two than later on. I run 700x28's at 70/75psi, and I only top up once or twice a week, once I'm past that initial period. I top up every day after replacing a tube.
I have a theory as to why, but really need to talk to someone better with fluid dynamics to see if it's remotely plausible.
#7
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,885
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5884 Post(s)
Liked 2,727 Times
in
1,521 Posts
There's no "normal" rate of air loss.
It depends on several factors.
Tire width - wider tires have a higher volume to surface area ratio, so they'll lose air slower
Tire pressure - pressure is the driving force, so the loss rate is roughly proportional to pressure.
Tube material - some materials are more permeable and allow air molecules through more easily.
Tube wall thickness - thicker walls resist bleed better than thinner ones.
While the first three are pretty much fixed by rider choices based on other things factors, the last is often forgotten about and can vary significantly. Different brands have different wall thickness, so a heavier tube of the same size may be preferable. Also consider that the tube stretches to fill the tire. A smaller tube will stretch more, thinning the walls in the process.
So, one way to slow bleed is to buy the largest, heaviest tube that fits rather than a smaller one used near the upper limit of it's range.
It depends on several factors.
Tire width - wider tires have a higher volume to surface area ratio, so they'll lose air slower
Tire pressure - pressure is the driving force, so the loss rate is roughly proportional to pressure.
Tube material - some materials are more permeable and allow air molecules through more easily.
Tube wall thickness - thicker walls resist bleed better than thinner ones.
While the first three are pretty much fixed by rider choices based on other things factors, the last is often forgotten about and can vary significantly. Different brands have different wall thickness, so a heavier tube of the same size may be preferable. Also consider that the tube stretches to fill the tire. A smaller tube will stretch more, thinning the walls in the process.
So, one way to slow bleed is to buy the largest, heaviest tube that fits rather than a smaller one used near the upper limit of it's range.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#8
Senior Member
Join Date: Jun 2009
Location: Silicon Valley, CA
Posts: 3,209
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 139 Post(s)
Liked 33 Times
in
20 Posts
I ride 25c tires at 100 psi. Usually commute 28 miles per day, MTThF. I fill up on Monday and again on Thursday. Tires are often down to 85-90 psi. I'll also fill up if I ride on the weekend. Weight with back pack and clothing is probably close to 170.
Generally, the higher the pressure, the rate of air leak is greater.
I agree that I think you have a slow leak. Odd that you are still seeing issues on both wheels with new tires and tubes, though. I can tell when I have an issue when I see either front/back having a much different pressure than the other.
Are you measuring tire pressure with the same device? You aren't losing a lot of air measuring pressure by misaligning the connector and losing air? I do that sometimes. Your situation seems somehow strange and I wonder what else is going on.
Generally, the higher the pressure, the rate of air leak is greater.
I agree that I think you have a slow leak. Odd that you are still seeing issues on both wheels with new tires and tubes, though. I can tell when I have an issue when I see either front/back having a much different pressure than the other.
Are you measuring tire pressure with the same device? You aren't losing a lot of air measuring pressure by misaligning the connector and losing air? I do that sometimes. Your situation seems somehow strange and I wonder what else is going on.
#9
Senior Member
Join Date: May 2017
Location: Etobicoke, Ontario, Canada
Posts: 162
Bikes: 2018 Trek Emonda SL w/Vision metron 40 wheelset, ultegra gruppa. 2010 Intense Tracer VP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 69 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Since it hasn't been asked...What are you filling your tires with? Ambient air? Nitrogen? Co2? or? Different gasses will cause different pressure drops.
I use nitrogen, 125psi drops to 100psi in a week, so I top it up once a week.
Matt
I use nitrogen, 125psi drops to 100psi in a week, so I top it up once a week.
Matt
Last edited by awesomeame; 09-02-17 at 05:07 PM.
#10
Senior Member
Join Date: May 2017
Location: Etobicoke, Ontario, Canada
Posts: 162
Bikes: 2018 Trek Emonda SL w/Vision metron 40 wheelset, ultegra gruppa. 2010 Intense Tracer VP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 69 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Matt
#11
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,885
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5884 Post(s)
Liked 2,727 Times
in
1,521 Posts
No, you'll never find wall thickness listed anywhere for two reasons.
The first is that the thickness will vary according to how the tube stretches when filled, and the second is that nobody cares.
But you can get a sense of the relative thickness by weighing the tube. The actual uninflated width also counts and this is probably more to the point. A wider tube stretches less in use, so ens up with thicker walls. So look for the widest size that will fit, ie. for a 38c tire, you want a tube marked fits 38-48mm rather than one marked fits 28-40mm.
Unfortunately, the markings on the box can be a bit deceiving. There's only a very loose connection between the marked "fits XXXX" and the actual width, so your best bit is to open the box and look at the actual width of the rolled tube. The actual uninflated width will be roughly 1.5 times the flat width, so working backward, you want a tube 2/3rds (tolled up flat) the tire's width so there's minimum stretch when installed and inflated.
Note, wider tubes can sometimes be a bit harder to mount without pinching, so if you run into mounting issues, buy something a bit smaller next time.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#12
Unlisted member
Thread Starter
Join Date: Dec 2005
Location: Chicagoland
Posts: 6,192
Bikes: Specialized Hardrock
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1376 Post(s)
Liked 432 Times
in
297 Posts
I'm filling the tire with ambient air. I checked this afternoon before the first ride since the post and had only lost about 5 pounds of air according to the same Topeak floor pump I last used to top it off. I'm going to keep checking for a while and hope thing settle down - it's been a while since I had to replace a tube and think I'm just forgetting how I had to do this before.
#14
Senior Member
Join Date: Dec 2004
Location: Middle of da Mitten
Posts: 12,487
Bikes: Trek 7500, RANS V-Rex, Optima Baron, Velokraft NoCom, M-5 Carbon Highracer, Catrike Speed
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1514 Post(s)
Liked 735 Times
in
456 Posts
If nitrogen really did leak out more slowly than other gasses, the 70% nitrogen in atmospheric air would naturally distill as other gasses leaked out of the tube, eventually leaving you with all nitrogen. But it doesn't work that way, does it? Nitrogen inflation might make a small difference in aviation, where getting rid of all moisture matters, but not in bike tires.
I've found that tire thickness also has a bearing on air loss. While it's the tube that mostly holds the air, apparently the tire walls can also help to impede leakage.
I've found that tire thickness also has a bearing on air loss. While it's the tube that mostly holds the air, apparently the tire walls can also help to impede leakage.
#15
Junior Member
Join Date: Jul 2017
Location: Lafayette
Posts: 6
Bikes: Trek 7200
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How about a soap test? Water + dishwashing liquid, swab it on the tire a small section at a time and look for bubbles. The air valve is a good place to start.
#17
Banned
Join Date: Apr 2010
Location: Lincoln Ne
Posts: 9,924
Bikes: RANS Stratus TerraTrike Tour II
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 3352 Post(s)
Liked 1,056 Times
in
635 Posts
All tubes lose air. Thats why I top off the pressure before every ride. The main reason is that you can track abnormal air loss which would indicate a puncture. Generally I ride every other day. The normal loss I see is maybe 5 pounds. If it is a lot more, I remove the tire and check the tube in water. If there is a leak, then of course I check the inside of the tire for what caused the leak.
#19
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,946
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2623 Post(s)
Liked 1,964 Times
in
1,230 Posts
It might be worth you while to inflate the patched tubes (until they balloon up a little bit) and check for leaks in the kitchen sink full of water. If it bubbles, mark it and patch it.
Boo, hiss.....
#20
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,566
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 984 Post(s)
Liked 589 Times
in
404 Posts
Actually it's 78% (ie, close to 80%! reference: https://en.wikipedia.org/wiki/Atmosphere_of_Earth). The rest is correct! When the conversation turns to car tire inflation and nitrogen, I always mention that I fill my tires with 80% nitrogen; very few people are aware that it's just *air*.
Steve
Steve
#21
Senior Member
The thorn-resistant tubes I have bought listed their thicknesses. I've seen some tubes advertised as extra-light, which means thinner.
I didn't notice that the thorn-resistant retained pressure all that much better, but I didn't measure closely.
I didn't notice that the thorn-resistant retained pressure all that much better, but I didn't measure closely.
#23
Senior Member
Join Date: Jun 2013
Location: Bozeman
Posts: 4,094
Bikes: 199? Landshark Roadshark, 198? Mondonico Diamond, 1987 Panasonic DX-5000, 1987 Bianchi Limited, Univega... Chrome..., 1989 Schwinn Woodlands, Motobecane USA Record, Raleigh Tokul 2
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1131 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If nitrogen really did leak out more slowly than other gasses, the 70% nitrogen in atmospheric air would naturally distill as other gasses leaked out of the tube, eventually leaving you with all nitrogen. But it doesn't work that way, does it? Nitrogen inflation might make a small difference in aviation, where getting rid of all moisture matters, but not in bike tires.
I've found that tire thickness also has a bearing on air loss. While it's the tube that mostly holds the air, apparently the tire walls can also help to impede leakage.
I've found that tire thickness also has a bearing on air loss. While it's the tube that mostly holds the air, apparently the tire walls can also help to impede leakage.
#24
Senior Member
Join Date: Feb 2009
Location: Southwest MO
Posts: 782
Bikes: (2) 1994 Cannondale R900, red, Silver Trek hybrid
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 69 Post(s)
Liked 4 Times
in
4 Posts
The difference I saw was a lot. Latex tubes leaked down a lot faster than butyl rubber.
I don't recommend them unless you like refilling tires a lot.
With butyl tubes over a week I see a loss of about 15 lbs from 110 lbs on a 700x23c tire. I saw that much overnight on latex.
I don't recommend them unless you like refilling tires a lot.
With butyl tubes over a week I see a loss of about 15 lbs from 110 lbs on a 700x23c tire. I saw that much overnight on latex.
#25
Senior Member
Join Date: Dec 2004
Location: Middle of da Mitten
Posts: 12,487
Bikes: Trek 7500, RANS V-Rex, Optima Baron, Velokraft NoCom, M-5 Carbon Highracer, Catrike Speed
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1514 Post(s)
Liked 735 Times
in
456 Posts
The difference I saw was a lot. Latex tubes leaked down a lot faster than butyl rubber.
I don't recommend them unless you like refilling tires a lot.
With butyl tubes over a week I see a loss of about 15 lbs from 110 lbs on a 700x23c tire. I saw that much overnight on latex.
I don't recommend them unless you like refilling tires a lot.
With butyl tubes over a week I see a loss of about 15 lbs from 110 lbs on a 700x23c tire. I saw that much overnight on latex.