How to restoring classic caliper brakes?
#1
Junior Member
Thread Starter
How to restoring classic caliper brakes?
Hi guys. Can you please help me on how to remove these stains from a classic caliper brake to make it oh so shiny again? Its from a 1989 bridgestone roadman. Thanks guys!
#2
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,844
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2297 Post(s)
Liked 2,047 Times
in
1,253 Posts
Make two more posts and you can upload pics
#3
Senior Member
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,433
Bikes: A bunch of old bikes and a few new ones
Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5888 Post(s)
Liked 3,471 Times
in
2,079 Posts
First deal with any dirt with a simple wash. If necessary try something stronger like simple green or a citrus based solvent.
Second if dealing with rust, evaporust does the job.
Once the calipers are clean try a polish like mothers
Second if dealing with rust, evaporust does the job.
Once the calipers are clean try a polish like mothers
Last edited by bikemig; 09-11-20 at 02:34 PM.
Likes For bikemig:
#5
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,844
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2297 Post(s)
Liked 2,047 Times
in
1,253 Posts
So tell me what model calipers you have.
#6
Junior Member
Thread Starter
Finally able to upload photos. Haha.
Its a dia-compe. I have very little knowledge on bikes. Apologies if this arw silly questions.
Its a dia-compe. I have very little knowledge on bikes. Apologies if this arw silly questions.
#8
Senior Member
Join Date: Jul 2014
Posts: 1,486
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 1081 Post(s)
Liked 681 Times
in
438 Posts
Nothing a little elbow grease won't take care of. I'd use Mother's Mag and Aluminum polish, which is sold all over. You can make those look like new again.
If you have a buffing wheel it would take 5 minutes. By hand, a little longer.
If you have a buffing wheel it would take 5 minutes. By hand, a little longer.
Likes For Jeff Neese:
#9
Senior Member
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,433
Bikes: A bunch of old bikes and a few new ones
Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5888 Post(s)
Liked 3,471 Times
in
2,079 Posts
You may want to replace those brake pads; kool stops are very good.
#10
Senior Member
Mothers mag and aluminum works great !!
#11
Senior Member
Join Date: May 2011
Location: Seattle WA
Posts: 2,841
Bikes: 2009 Handsome Devil, 1987 Trek 520 Cirrus, 1978 Motobecane Grand Touring, 1987 Nishiki Cresta GT, 1989 Specialized Allez Former bikes; 1986 Miyata Trail Runner, 1979 Miyata 912, 2011 VO Rando, 1999 Cannondale R800, 1986 Schwinn Passage
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 522 Times
in
367 Posts
New pads - too after the calipers are all cleaned up and springs lightly lubed, Kool Stop is a good choice.
#12
Senior Member
It's light oxidation, AKA aluminum rust. It'll come right off with metal polish and a rag and elbow grease, like everyone says. They'll shine like chrome. I typically use Simichrome. Mothers will work, or Wenol, or probably about a dozen others.
FYI those are Bridgestone self centering brakes, made by Dia Compe. Neat design.
It is easiest to polish them if you take them apart. But don't do that unless you're confident in your mechanical skills. They'll clean up well enough if you leave them together. Give the pivot points a drop of oil when you're done.
FYI those are Bridgestone self centering brakes, made by Dia Compe. Neat design.
It is easiest to polish them if you take them apart. But don't do that unless you're confident in your mechanical skills. They'll clean up well enough if you leave them together. Give the pivot points a drop of oil when you're done.
Likes For datord:
#14
Senior Member
Join Date: Jan 2016
Posts: 3,442
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 872 Post(s)
Liked 2,272 Times
in
1,274 Posts
I use Mothers Polish and on those you my need super fine steel wool first. I think taking them apart will render the best result. But as Salamandrine says be sure you have the skill to correctly reassemble. If not put together right then modulation can be off. They will look like chrome when finished. I usually do it while watching tv. I have done a few sets of side pull and center pull.
#15
Senior Member
Join Date: Mar 2015
Location: Western MI
Posts: 2,767
Mentioned: 45 Post(s)
Tagged: 0 Thread(s)
Quoted: 655 Post(s)
Liked 467 Times
in
301 Posts
All good polishes mentioned above. They’ll clean up the first pic but I doubt they’ll get rid of the spots. 2 or 3 stage wet sand followed by the polish will make them pop. 300/1000 grit (or approximate) for a nice shiny finish. 300/1000//2500 for a high polish finish. All able to be done by hand.
#16
Senior Member
Don't spend too much on chrome cleaner. The cheap stuff works just as good as anything else.
https://www.turtlewax.com/en-us/our-...-rust-remover/
https://www.turtlewax.com/en-us/our-...-rust-remover/
#17
Senior Member
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
ooh, nice - Dia Compe SCs!! (self centering that really works!) i have two sets of these in use and I think they're kinda great brakes. They always seem to turn up on Bridgestones.
Another cleaning idea is to toss the whole caliper into an Oxalic acid bath - that will take the rust off the steel bits, but will also clean the (unanodized) aluminum back to a brighter, pale grey - from which point the polishing becomes much easier. (I use Blue Magic for raw aluminum, with a scotchbrite pad when tackling the peppering you have here)
You may also want to check & lube everything as part of the clean up - the mechanism is simple and clever, but it does require that parts can turn against each other in a tight "friction fit". a decade or three sitting outside can often end up killing the "SC" part of things until a refurb.
Another cleaning idea is to toss the whole caliper into an Oxalic acid bath - that will take the rust off the steel bits, but will also clean the (unanodized) aluminum back to a brighter, pale grey - from which point the polishing becomes much easier. (I use Blue Magic for raw aluminum, with a scotchbrite pad when tackling the peppering you have here)
You may also want to check & lube everything as part of the clean up - the mechanism is simple and clever, but it does require that parts can turn against each other in a tight "friction fit". a decade or three sitting outside can often end up killing the "SC" part of things until a refurb.
Last edited by niliraga; 09-11-20 at 05:42 PM.
#18
Senior Member
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,748
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 702 Post(s)
Liked 671 Times
in
419 Posts
1) disassemble
2) green scotch pad and water
3) metal polish and micro-fiber cloth
4) grease pivots
5) assemble
6) Kool-Stop pads
7) ride
8)
2) green scotch pad and water
3) metal polish and micro-fiber cloth
4) grease pivots
5) assemble
6) Kool-Stop pads
7) ride
8)
Likes For branko_76:
#19
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1607 Post(s)
Liked 2,214 Times
in
1,103 Posts
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
Likes For SJX426:
#20
Junior Member
Thread Starter
Hey guys! Here's how my brakes look like now. I used 3M metal polish and sanded the parts that didn't come off.
Thanks for all the help.
Thanks for all the help.
#21
Senior Member
Join Date: Mar 2015
Location: Western MI
Posts: 2,767
Mentioned: 45 Post(s)
Tagged: 0 Thread(s)
Quoted: 655 Post(s)
Liked 467 Times
in
301 Posts
Looking good. Now make the call on how shiny you want them. Polish and leave as is, hit them with wet 1,000 grit and polish or go all the way by following up with wet 2,500 grit and polish. They’ll end up like this which is hard to believe until you’ve done it.
DSCN2438 (600x450)
DSCN2438 (600x450)
Likes For plonz:
#22
Junior Member
Thread Starter
Looking good. Now make the call on how shiny you want them. Polish and leave as is, hit them with wet 1,000 grit and polish or go all the way by following up with wet 2,500 grit and polish. They’ll end up like this which is hard to believe until you’ve done it.
DSCN2438 (600x450)
DSCN2438 (600x450)