Rear derailleur sometimes jumping sprockets
#1
Junior Member
Thread Starter
Rear derailleur sometimes jumping sprockets
I am ok with installing and adjusting front derailleurs, but have never messed with rear derailleurs. I have found an intermittent issue with the rear derailleur. Sometimes when I am on the third gear from the top, then go to switch to the next gear, it makes two shifts at once, putting me in the highest gear. What adjustment is likely out and causing this?
Thanks,
Danny
Thanks,
Danny
Last edited by kaiserschmarrn; 08-12-20 at 09:54 PM.
Likes For trailangel:
#5
Senior Member
I am ok with installing and adjusting front derailleurs, but have never messed with rear derailleurs. I have found an intermittent issue with the rear derailleur. Sometimes when I am on the third gear from the top, then go to switch to the next gear, it makes two shifts at once, putting me in the highest gear. What adjustment is likely out and causing this?
Thanks,
Danny
Thanks,
Danny
#7
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
Probably. Shift to the lowest tension which is usually the highest gear (smallest cog on the back). Check the tension on the cable by plucking it. It should have a little bit of twang but it shouldn’t be as tight as a guitar string. Most of the time the cable is too slack...indicated by being able to pull it away from the frame...but sometimes it is too tight. If it is “twangy”, back off on the barrel adjuster on the rear derailer or on the shifter or frame (depending on what kind of shifter you have). Then run the bike through the gears. One click should move the derailer on gear.
If that doesn’t work, you might have some issues with the outer cable. It might be dragging on the inner cable causing too much tension. Shift the bike to the lowest gear (largest cog, again assuming regular “high normal” derailer). (The pictures below are for a mountain bike but works for road bikes too)
Library - 3391 by Stuart Black, on Flickr
Now, without pedaling, shift up which releases tension on the cable
Library - 3392 by Stuart Black, on Flickr
This will make the cable very slack
Library - 3393 by Stuart Black, on Flickr
You should be able to pull the cable out of the frame
Library - 3394 by Stuart Black, on Flickr
Library - 3395 by Stuart Black, on Flickr
and pull it away from the shifter as well. Put a little grease on your thumb and forefinger and run it up and down the inner cable. Lubricate anything that is under the outer cable.
While you have the cable slack, inspect the ends of the cable and see if there are any wires poking out of the ferrule like this
IMG_1361 by Stuart Black, on Flickr
If there are, this means that the outer cable probably needs replaced since the rods in the outer cable have come loose. The loose wires will cause the inner cable to jam. You should be able to pull most ferrules off the cable housing to look for this kind of stucture
IMG_1362 by Stuart Black, on Flickr
Cable tension and cable lubrication are usually the problem. That should cover 99% of all issues. If that doesn’t work, check the derailer hanger...you can eyeball it to see if the cassette, upper wheel and lower wheel line up. But it’s usually the cable.
If that doesn’t work, you might have some issues with the outer cable. It might be dragging on the inner cable causing too much tension. Shift the bike to the lowest gear (largest cog, again assuming regular “high normal” derailer). (The pictures below are for a mountain bike but works for road bikes too)
Library - 3391 by Stuart Black, on Flickr
Now, without pedaling, shift up which releases tension on the cable
Library - 3392 by Stuart Black, on Flickr
This will make the cable very slack
Library - 3393 by Stuart Black, on Flickr
You should be able to pull the cable out of the frame
Library - 3394 by Stuart Black, on Flickr
Library - 3395 by Stuart Black, on Flickr
and pull it away from the shifter as well. Put a little grease on your thumb and forefinger and run it up and down the inner cable. Lubricate anything that is under the outer cable.
While you have the cable slack, inspect the ends of the cable and see if there are any wires poking out of the ferrule like this
IMG_1361 by Stuart Black, on Flickr
If there are, this means that the outer cable probably needs replaced since the rods in the outer cable have come loose. The loose wires will cause the inner cable to jam. You should be able to pull most ferrules off the cable housing to look for this kind of stucture
IMG_1362 by Stuart Black, on Flickr
Cable tension and cable lubrication are usually the problem. That should cover 99% of all issues. If that doesn’t work, check the derailer hanger...you can eyeball it to see if the cassette, upper wheel and lower wheel line up. But it’s usually the cable.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute: