Are all canti brakes the same?
#1
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Are all canti brakes the same?
I just picked up a bike with cantilever brakes, a first for me.
Looking to upgrade to a nice set and I've noticed that outside of the arm geometry/angle and straddle wires, there's nothing mentioned about the size.
Do all canti's have the same relationship to boss/pivot, pad location, etc? Or am I missing something? Like when side or centerpulls talk about reach...
Looking to upgrade to a nice set and I've noticed that outside of the arm geometry/angle and straddle wires, there's nothing mentioned about the size.
Do all canti's have the same relationship to boss/pivot, pad location, etc? Or am I missing something? Like when side or centerpulls talk about reach...
#2
Pedalin' Erry Day
Yep, the size and positioning of cantilever studs are standardized - you can swap in whatever cantis you like and they will work. There are differences in shapes, angles, pad style, and there are slight differences in the adjustment procedure between the different kinds of cantilevers, but they all use the same studs.
If you want a recommendation for modern, new canti's, I like the Tektro CR720's: they work well, are relatively easy to setup, look good, affordable, and they come with nice pad holders that use standard road pads and are easily adjusted.
If you want a recommendation for modern, new canti's, I like the Tektro CR720's: they work well, are relatively easy to setup, look good, affordable, and they come with nice pad holders that use standard road pads and are easily adjusted.
#3
Aspiring curmudgeon
Join Date: Aug 2014
Location: Saint Louis
Posts: 2,486
Bikes: Guerciotti, Serotta, Gaulzetti
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Likes: 0
Liked 26 Times
in
13 Posts
I will second the plug for Tektro 720s. Very nice brakes for the coin.
__________________
"Party on comrades" -- Lenin, probably
"Party on comrades" -- Lenin, probably
#4
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yep, the size and positioning of cantilever studs are standardized - you can swap in whatever cantis you like and they will work. There are differences in shapes, angles, pad style, and there are slight differences in the adjustment procedure between the different kinds of cantilevers, but they all use the same studs.
If you want a recommendation for modern, new canti's, I like the Tektro CR720's: they work well, are relatively easy to setup, look good, affordable, and they come with nice pad holders that use standard road pads and are easily adjusted.
If you want a recommendation for modern, new canti's, I like the Tektro CR720's: they work well, are relatively easy to setup, look good, affordable, and they come with nice pad holders that use standard road pads and are easily adjusted.
#5
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#6
Still learning
#7
Senior Member
I highly recommend measuring your spacing on the studs before buying new brakes if the bike is from the 80s.
#8
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
This isn't the whole story. The spacing between the posts has changed. Touring bikes from the 80s tend to have the studs spaced 65mm or so while mountain bikes and modern hybrids, cx and touring bikes seem to be in the 80+mm area. For example on a bianchi randonneur i had the only brakes that would work were vintage dia-compe becuase the posts were placed for 27" wheels. Modern cantis also didn't work on miyata 1000 because the posts were too close together. The shimano altus cantis are the only modern brakes I can think of that would work.
I highly recommend measuring your spacing on the studs before buying new brakes if the bike is from the 80s.
I highly recommend measuring your spacing on the studs before buying new brakes if the bike is from the 80s.
#9
Senior Member
It probably doesn't suffer from close spacing, I had a 90s miyata tricross that was able to take modern cantis no problem. Easy enough to double check with a ruler if the wheel is off.
#10
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#11
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,844
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2297 Post(s)
Liked 2,047 Times
in
1,253 Posts
Rim width factors into canti performance too. The typically wide Araya mtn rims from the 80's don't play well with modern canti's. Similar problem as the narrow post placement.
#12
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#13
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,749 Times
in
937 Posts
As I continue to replace everything on the bike that must have gone around the planet two or three times...
...I found that the Dia Compe cantilever brakes were badly worn. Not the pads, but the bushings that fit the posts. They were incredibly sloppy fitting. So...
Having only one set of cantilevers on hand, an old set of Weinmanns, I tried a swap. No problem. The Weinmanns fitted just perfectly. I can, however, have a set of Dia Compes off of a couple of scrap bicycles at B4H. I must ask to do so and, these days, I always give a nice donation for anything that I get.
I plan to do some picture taking today. I will snap a shot or two of this fix.
...I found that the Dia Compe cantilever brakes were badly worn. Not the pads, but the bushings that fit the posts. They were incredibly sloppy fitting. So...
Having only one set of cantilevers on hand, an old set of Weinmanns, I tried a swap. No problem. The Weinmanns fitted just perfectly. I can, however, have a set of Dia Compes off of a couple of scrap bicycles at B4H. I must ask to do so and, these days, I always give a nice donation for anything that I get.
I plan to do some picture taking today. I will snap a shot or two of this fix.
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#14
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,644
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2607 Post(s)
Liked 1,696 Times
in
935 Posts
This isn't the whole story. The spacing between the posts has changed. Touring bikes from the 80s tend to have the studs spaced 65mm or so while mountain bikes and modern hybrids, cx and touring bikes seem to be in the 80+mm area. For example on a bianchi randonneur i had the only brakes that would work were vintage dia-compe becuase the posts were placed for 27" wheels. Modern cantis also didn't work on miyata 1000 because the posts were too close together. The shimano altus cantis are the only modern brakes I can think of that would work.
I highly recommend measuring your spacing on the studs before buying new brakes if the bike is from the 80s.
I highly recommend measuring your spacing on the studs before buying new brakes if the bike is from the 80s.
The difference between different brakes is the difference in being able to make them work or not. This is especially evident when going from 27" to 700c.
FWIW- the front bosses on my Voyageur SP Are spaced at 50mm. For real.
#15
Keener splendor
I agree with the points @clasher points out.
In addition, the brakes themselves have a different relationship between the mounts, the pads and the frame. Clearance for the frame varies by brake manufacturer and model. With pads attached, some brakes will clear the frame/fork easily. Others will not. As far as I know, there is no reporting of this measurement.
In addition, the brakes themselves have a different relationship between the mounts, the pads and the frame. Clearance for the frame varies by brake manufacturer and model. With pads attached, some brakes will clear the frame/fork easily. Others will not. As far as I know, there is no reporting of this measurement.
#16
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,605
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10947 Post(s)
Liked 7,474 Times
in
4,181 Posts
#17
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Glendale, WI
Posts: 238
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I don't like them, they're ugly (no offense), looking to spruce it up.
#18
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,644
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2607 Post(s)
Liked 1,696 Times
in
935 Posts
I think they're pretty spiffy looking when they're cleaned up- but then again, the XC Pro cantis are my favorite brake.
If you're lucky, the Tektro 720 will work on there, unless you want to hunt down some XC Pros...