A learning curve question!
#1
Senior Member
Thread Starter
Join Date: Dec 2011
Location: NE Ohio
Posts: 2,595
Bikes: 1992 Serotta Colorado II,Co-Motion Speedster, Giant Escape Hybrid, 1977 Schwinn Super Le Tour
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 455 Post(s)
Likes: 0
Liked 112 Times
in
85 Posts
A learning curve question!
I have read about some you fellows building your own racks out of ss tubing. I have access to tig welding.
How much of a learning curve would you say for a complete novice to fabricate pannier racks?
Our Tubus ones,black , regular maintenance and I like the look of ss.
Thanks
How much of a learning curve would you say for a complete novice to fabricate pannier racks?
Our Tubus ones,black , regular maintenance and I like the look of ss.
Thanks
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,052
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4193 Post(s)
Liked 3,837 Times
in
2,295 Posts
To make a nice rack I suspect you'll spend close to what a new rack costs in materials. The skills to TiG SS well, and on such small and thin walled tubing, will take a bunch of practice. A bunch. Then there's the tools besides the TiG machine and the back purge gas and it's fittings. (Far more common is brazing the SS tubes but still has costs).
I just finished my 4th full sized rack, it has a couple of tail light brackets and wire clips built on. I didn't track my time but I bet I have well over 20 hours in it. Maybe 10 feet of tubing along with various other bits, some self made and some bought.
Expect to go through the same "next time I should do it this/that way" moments a number of times. And that's after getting the basic fabrication skills thing down. Andy
I just finished my 4th full sized rack, it has a couple of tail light brackets and wire clips built on. I didn't track my time but I bet I have well over 20 hours in it. Maybe 10 feet of tubing along with various other bits, some self made and some bought.
Expect to go through the same "next time I should do it this/that way" moments a number of times. And that's after getting the basic fabrication skills thing down. Andy
__________________
AndrewRStewart
AndrewRStewart
#3
Senior Member
Thread Starter
Join Date: Dec 2011
Location: NE Ohio
Posts: 2,595
Bikes: 1992 Serotta Colorado II,Co-Motion Speedster, Giant Escape Hybrid, 1977 Schwinn Super Le Tour
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 455 Post(s)
Likes: 0
Liked 112 Times
in
85 Posts
Thanks for your reply! Chalk that off my list!
#4
Banned
I took a liking to the metalsmith Art department classes at the Community College for a few years,
and had workshop access.
then I tackled a DIY Frame.. brazed, lugs...
But I moved away long since..
....
and had workshop access.
then I tackled a DIY Frame.. brazed, lugs...
But I moved away long since..
....
#5
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,832
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2336 Post(s)
Liked 2,808 Times
in
1,534 Posts
check out some posts by @gugie he does a lot of racks..... I think he brazes.....not sure if that would be easier than tig or not.......not my area of expertise....yet
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#6
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,385
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,686 Times
in
2,509 Posts
the setup for the first rack is expensive, no matter what the joining tech is. I use silver on SS racks, so that's some money right up front. And you can't buy one rack's worth of silver. I suppose you could figure out how to bend tubing with a cheap bender or even make the bender yourself out of pulleys, for example. But I still see getting to the point where you could build a usable first rack as being about equal to what it costs to buy a SS rack from Tubus
#7
Senior Member
Thread Starter
Join Date: Dec 2011
Location: NE Ohio
Posts: 2,595
Bikes: 1992 Serotta Colorado II,Co-Motion Speedster, Giant Escape Hybrid, 1977 Schwinn Super Le Tour
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 455 Post(s)
Likes: 0
Liked 112 Times
in
85 Posts
I think Tubus has discontinued their SS front racks.
#8
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,385
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,686 Times
in
2,509 Posts
that would be too bad, I was never too impressed by the black ones
#9
Senior Member
Thread Starter
Join Date: Dec 2011
Location: NE Ohio
Posts: 2,595
Bikes: 1992 Serotta Colorado II,Co-Motion Speedster, Giant Escape Hybrid, 1977 Schwinn Super Le Tour
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 455 Post(s)
Likes: 0
Liked 112 Times
in
85 Posts
I have been re-painting ours every year after our tours. This time added Gorilla tape at the wear points.
#10
Banned
abrasion patches were already thought of.. : https://www.tubus.com/produkte/zubeh...folienset/#ass