Stripped Crank Arm
#1
Junior Member
Thread Starter
Join Date: Mar 2024
Location: San Diego
Posts: 126
Bikes: Paramount Track Bike, Colnago Super, Santana Tandems (1995 & 2007), Gary Fisher Piranha, Trek Wahoo, Bianchi Track Bike, a couple of Honda mountain bikes
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 58 Post(s)
Liked 31 Times
in
20 Posts
Stripped Crank Arm
An unnamed knucklehead stripped the threads on my Alivio crank arm (square bottom bracket).
Does anyone know any good tricks for getting it off, or am I going to have to resort to a bandsaw?
TIA, Mike
Does anyone know any good tricks for getting it off, or am I going to have to resort to a bandsaw?
TIA, Mike
#2
Cantilever believer
Join Date: Nov 2021
Location: Phoenix, AZ
Posts: 1,571
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 537 Post(s)
Liked 1,845 Times
in
835 Posts
I feel for you. I've lost a crank or two that way, even after stopping and using lots of penetrant after the pulling got hard. Sometimes the crank threads lose the battle - even sadder when it's a rare and valuable old crank you wanted to save.
I've tried a jaw puller, but with 0% success. What has worked is multiple cuts with an angle grinder, working carefully in case you want to salvage the bottom bracket.
I've tried a jaw puller, but with 0% success. What has worked is multiple cuts with an angle grinder, working carefully in case you want to salvage the bottom bracket.
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Likes For RCMoeur:
#3
Really Old Senior Member
https://www.harborfreight.com/16-in-...iABEgIRmvD_BwE
Of the appropriate size-
Of the appropriate size-
#4
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
Often, removing the mounting bolt and riding around the block a few times is enough to work the arm loose. Don't go too far from home/shop, as once it gets loose you'll want to stop riding and walk back, or risk ruining the crank arm. There are kits to cut new threads into stripped arms; too costly for a one-off job, but perhaps a local shop has one.
Likes For JohnDThompson:
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,098
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4211 Post(s)
Liked 3,881 Times
in
2,316 Posts
One trick is to go ride the bike with a crank arm retaining bolt only finger tight. In time the crank will come loose and the bolt will keep it from falling off the bike while you limp home. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#6
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
Back the bolt off half turn from tight, and do sprint intervals near home. The arm will come free with an audible pop.
If that fails, leave the bolt off and join some friends on a century in the Poconos. (based on experience)
Otherwise, buy a pair of #6 Jacob's Chuck wedges for a few dollars.
Likes For FBinNY:
#7
Senior Member
Join Date: Mar 2012
Posts: 982
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 506 Post(s)
Likes: 0
Liked 639 Times
in
357 Posts
Often, removing the mounting bolt and riding around the block a few times is enough to work the arm loose. Don't go too far from home/shop, as once it gets loose you'll want to stop riding and walk back, or risk ruining the crank arm. There are kits to cut new threads into stripped arms; too costly for a one-off job, but perhaps a local shop has one.
#8
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
Likewise, tapping new threads, would mean a larger size for which you'd need to seek a non-existent remover.
HOWEVER - if one ops to use Jacob's Chuck wedges, the crank can be reused and removed the same way as often as needed. Likewise, with the ride till it comes loose approach, though that would be less convenient.
In summary, I see no need to "fix" or trash the otherwise good crank arm.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#9
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,677
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 839 Post(s)
Liked 1,064 Times
in
747 Posts
One trick I used once was to loosen the bolt a turn or two, get yourself an assistant to hold the bike a few inches off and parallel to the floor by holding onto the crankarm or chainrings and then you use a drift to give a decent smack to the head of the crank bolt. This should move the crank just enough to come loose from the BB axle. Don't get too carried away with the hammer and may take a few hits. Heat to the crank first may help a little but to be safe pour some boiling water over it rather than a flame.
#11
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,098
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4211 Post(s)
Liked 3,881 Times
in
2,316 Posts
JA Stein made (makes currently?) a crank extractor thread repair kit It has an oversized thread tap (pilot too IIRC) and the now oversized extractor/puller.
Bicycle Research and BR offered an extractor thread chaser w/ pilot. here's a shot of it. Andy
Bicycle Research and BR offered an extractor thread chaser w/ pilot. here's a shot of it. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#12
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
#13
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
That's how the VAR kit I mentioned above works. It cuts new, 24mm x 1.5mm threads, and then sell the customer the 24 x 1.5 thread self-extractors for subsequent crank removals.
#14
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
Yes, and BITD we also sometimes retapped cranks to use Stronglight removers. But, IMO, we need to self impose cost limits for saving anything short of a true collectible.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#15
Full Member
One time the outer few threads on a crank arm were buggered up and I just couldn't get the crank puller started. I machined a steel rod to both fit closely into the bolt hole of the bottom bracket axle (so the rod was square) and a close fit on the hole in the crank puller. Once the crank puller was all lined up I was able to get it started. Carefully working it in, I eventually got it all the way seated and had enough threads into the crank arm to allow the puller to work. This is not very helpful advice if you don't have access to a lathe, however. Sorry if this therefore doesn't help!
Likes For joeruge:
#16
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,985
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26427 Post(s)
Liked 10,382 Times
in
7,210 Posts
https://steintool.com/portfolio-item...-system/...175 bucks (ouch).
For the OP, I would just either find a pickle fork, or an angle grinder, destroy that Alivio crank removing it, and replace with something better. But I have stuff that is better.
...
...
__________________
Last edited by 3alarmer; 03-26-24 at 06:15 PM.
#17
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,517
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,401 Times
in
2,058 Posts
Likes For dedhed:
#18
Full Member
Andy, this tool looks essentially like what was trying to describe. I'm guess that the smaller threaded 'stud' screws into the axle of the bottom bracket and it aligns the thread cutting portion. I didn't know they made such a thing. Very cool!
#19
Junior Member
Thread Starter
Join Date: Mar 2024
Location: San Diego
Posts: 126
Bikes: Paramount Track Bike, Colnago Super, Santana Tandems (1995 & 2007), Gary Fisher Piranha, Trek Wahoo, Bianchi Track Bike, a couple of Honda mountain bikes
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 58 Post(s)
Liked 31 Times
in
20 Posts
Thanks everyone!
Riding it with the crank bolt loose sounds promising.
Riding it with the crank bolt loose sounds promising.
#20
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
#22
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,098
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4211 Post(s)
Liked 3,881 Times
in
2,316 Posts
#23
Senior Member
Join Date: Apr 2016
Posts: 1,242
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 504 Post(s)
Liked 436 Times
in
335 Posts
Is it worth the effort for a few uses? Just cut the two threads in some cold rolled round bar - done; you could knurl it or mill flats for easier use. And you'd have to mount the crank on an axle (or mount it on a face plate) and thread that too. People do this stuff for fun, you just have to find them.
Last edited by grumpus; 03-27-24 at 08:48 AM.
#24
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,119
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 659 Times
in
372 Posts
EDIT: Guess it was already mentioned, but I will say +1 to those that say it works well.
Last edited by Dan Burkhart; 03-27-24 at 09:43 AM.
#25
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,820
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 840 Post(s)
Liked 1,262 Times
in
667 Posts
just loosen the bolt and ride around the block a couple times.
/markp
/markp