possible BF pakiT Buy
#1
Senior Member
Thread Starter
Join Date: Apr 2018
Location: West Sacramento CA
Posts: 65
Bikes: Electra Cruiser 7D, Dahon Boardwalk, Sundeal F1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 5 Times
in
4 Posts
possible BF pakiT Buy
What do you all think about a BF pakiT IGH 3spd Sturmey Archder, Ritchie bike post, Kojak Schwalbe with less than 100 miles for $1k or OBO. I am about to pull the trigger and buy it. He says that their is a "rattle" when you back pedal on the coaster brake, but not when you pedal. He is including the "Albatross" bars and I will have to get some new pedals.
#4
Senior Member
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,463
Bikes: Trident Spike 2 recumbent trike w/ e-assist
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1321 Post(s)
Liked 374 Times
in
288 Posts
What do you all think about a BF pakiT IGH 3spd Sturmey Archder, Ritchie bike post, Kojak Schwalbe with less than 100 miles for $1k or OBO. I am about to pull the trigger and buy it. He says that their is a "rattle" when you back pedal on the coaster brake, but not when you pedal. He is including the "Albatross" bars and I will have to get some new pedals.
#5
Senior Member
I'm the seller, I paid $1200 (plus shipping) for it from the original owner last year. It's not a rattle in the hub, it's that the coaster brake creates a reaction in the junction where the rear triangle meets behind the seatpost. There's a smidge of movement there at the quick-release you wouldn't normally notice on a PakiT - it's not there while pedaling or coasting - that the step-on-the-brake setup agitates for some reason. The O-ring cushion in there is present, everything works right, it's just an oddity of putting a coaster brake on that design I guess. They don't seem to have made very many with this arrangement so I couldn't find any other information on it.
#6
Senior Member
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,463
Bikes: Trident Spike 2 recumbent trike w/ e-assist
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1321 Post(s)
Liked 374 Times
in
288 Posts
Ah, if that's the problem it is easy to isolate. Take a bit of tire tube about 3/8 in width and put around the black tube in front of the release pin and then close the rear triiangle. If the noise disappears when you ride and brake, then it is just the slack between the two (which does exist on all pakiTs to some degree). The more you open and close the triange, the more the paint will wear off the black tube portion and the slack will increase. Using a piece of inner tube as a "condom" was the solution that I arrived at with BF when I had this issue, which would happen even using my caliper brake. The tolerances on my replacement triangle are a little tighter so haven't had the need.
Or am I misunderstanding what you're defining as the issue, Joe? And if that's the problem, it's a non-problem and just part of the design tolerances.
Or am I misunderstanding what you're defining as the issue, Joe? And if that's the problem, it's a non-problem and just part of the design tolerances.
#7
Senior Member
Yep Linberl, that's the issue. I probably would have thought of that idea eventually but my riding time has been not-so-great the last year so I never got around to being bothered by it. For the rides I did do I got pretty slick at dragging the brake gently (or not at all) to keep the chatter down and mostly used the front caliper. If I kept the bike I would try your scheme.
#8
Junior Member
Join Date: Mar 2021
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What do you all think about a BF pakiT IGH 3spd Sturmey Archder, Ritchie bike post, Kojak Schwalbe with less than 100 miles for $1k or OBO. I am about to pull the trigger and buy it. He says that their is a "rattle" when you back pedal on the coaster brake, but not when you pedal. He is including the "Albatross" bars and I will have to get some new pedals.